HCL 10.4.8

From OSx86
Revision as of 13:38, 9 October 2013 by Poco (Talk | contribs)

Jump to: navigation, search
macOS 10.4.8
Hardware Compatibility

This is a component level hardware compatibility list. We want to keep it as accurate as possible, but please, do not entirely rely on this list when buying hardware. Add which parts you have working in the categories listed below, or create a new category. Please keep alphabetical order inside the categories. The categories themselves are ordered by popularity. Please list any caveats or problems as well.

  • ONLY add hardware that you have TESTED. Don't add hardware just because you think it might work.
  • Please add hardware into tables.
  • This is for 10.4.8 builds only.

For how to edit the Wiki, please see this thread. Thank you!

You're looking for an Installation guide? see here

Contents

Motherboard

A comprehensive list of possible Intel chipsets

PLEASE INCLUDE THE SOUTH BRIDGE TOO Also please note which CPU you are using

AMD

Abit

Hardware Name (socket type) Chipset Notes Fully working without patching
KN9 Ultra Nvidia nForce MCP55-Ultra (nForce 570 Ultra) Works: almost everything.
  • USB2 - works without patching
  • FireWire - works without patching
  • SATA - works (only read, write in the works) with AppleNForceSATA patch (Not for me! Bertdd)
  • PATA - works (For DMA and disks larger than 128GB follow these Instructions)
  • audio - ALC883 - works with 2.0 audio and 5.1 audio, with patch ALC883Audio, digital out not tested, but should work
  • nForce 570 Gigabit LAN does not work
  • suspend, poweroff - works
JaS 10.4.8 DVD for AMD SSE3
AN52 NVIDIA nForce 520 single chip Works: almost everything.
  • USB2 - works without patching
  • SATA - SATA Harddisk does not work
  • PATA - works (For DMA and disks larger than 128GB follow these Instructions)
  • audio - ALC883 - works with 2.0 audio and 5.1 audio, with patch ALC883Audio, digital out not tested, but should work
  • nForce 520 Gigabit LAN does not work
JaS 10.4.8 DVD for AMD SSE3
AX8 VIA K8T890 (South Bridge VT8237)
  • USB - fails except keyboard/mouse (fix on the way?).
  • Onboard Ethernet (Marvell) - Does not work.
  • Onboard AC97 sound - (Works, some config needed).
  • SATA - Works
  • PATA - Works
No
AV8 VIA K8T800 Works with JaS; no onboard ethernet (Marvell), no onboard AC97 sound, USB intermittently fails except keyboard/mouse (reboot to fix) Yes
NF-M2 nView Nvidia nForce 4300
  • Onboard Ethernet (Realtek RTL8111B) - Does not work
  • Onboard Sound (Realtek ALC883) - Works
  • Onboard GeForce 6150 - Does not work (only VESA, not Natit or Titan)
  • SATA - Not tested
  • PATA - Works
Yes, Uphuck 1.2 and 1.3 with sound driver
NF8-V2 (S 754) Nvidia nForce3 250

No patches

  • SATA works
  • PATA works
  • Sound 2 channels work (5 ch buggy), input n/tested
  • LAN works
  • All USB work

Sleep doesn't work

Yes, JaS 10.4.8 (10.4.9 ok)

BIOSTAR

Hardware Name (socket type) Chipset Notes Fully working without patching
K8M800-M7A VIA K8M800 (South Bridge VT8237R
  • USB 2.0 - Works
  • Onboard Realtek ALC655 6-Channel AC97 sound - Works
  • Onboard Ethernet (Realtek RTL8201BL) - Does not work.
  • SATA - Untested
  • PATA - Works
JaS 10.4.8 for Intel & AMD SSE3 PPF1 & PPF2

DFI

Hardware Name (socket type) Chipset Notes Fully working without patching
LANParty UT NF4 Ultra-D NForce 4 Ultra Both IDE & SATA working, ALC850 on-board audio works, Both NICs work (Marvell & Nvidia), USB has to be plugged in after its booted. JaS 10.4.8 AMD INTEL SSE2 SSE3 beta 2 DVD w/ semthex 8.8.1 and extra drivers (Azalia, NATIT, etc.)
SLI-DR Expert NForce 4 Ultra IDE and SATA Working, Audio Unknown, Marvell LAN Works, Nvidia Ethernet works, USB Devices must be unplugged then plugged back in at boot (or install USB 2.0 driver from the Forums). Jas install DVD AMD 10.4.8 SSE 3 TEST 1
Infnity RS482 ATI SB450 IDE Seems to have problems during installation proccess after finishing a install. Unknown working status as follows... Realtek ALC850, Northbridge ATI Radeon Xpress 200 and SATA does not work. NIC onboard Realtek RTL8110SB Gigabit onboard works. Nope

Digitron

Hardware Name (socket type) Chipset Notes Fully working without patching
DG-760GX SiS 760GX/SiS 964 Sound and vdeo not tested (using vdeo Geforce2 Mx400). Ethernet SiS 900 doesn't work. IDE works perfectly. USB 2.0 also perfectly. Sata not tested. JaS 10.4.8 AMD.Intel SSE2.SSE3 defiant diskutil biker880 ICH7-R patch integrated.iso

ECS

Hardware Name (socket type) Chipset Notes Fully working without patching
760GX-M (V1.1) (Socket 754) SiS 760GX/964 Base devices work (USB, Firewire, PS/2). Must disable legacy USB devices in BIOS for PS/2 mouse and keyboard to work.
  • Sound: Requires SiS 7012 Driver for correct line out/mic in.
  • Ethernet: Requires Realtek 8139 Driver.
  • ATA: Requires SiS Driver for all ATA channels to be active. All drives will appear as SATA devices, including DVD+-RW.
  • SATA: Works when set to IDE mode in BIOS and ID 0x01801039 added to Info.plist in above driver in "IOPCIPrimaryMatch" under "VIA SATA Controller".
  • Video: Basic VESA 3.0 framebuffer. AGP enabled with AGPGart.kext version extracted from this package. On board graphics are quite fast, but no QE/CI or OpenGL. Note: If AGPGart.kext is not modified QE AND CI are supported with nitan_uni.install.
  • Sleep: Does not wake from sleep.
Tubgirl: OSX_1048_AMD.iso (requires patches listed in Notes)
NFORCE4M-A (v3.0) (Socket AM2) nForce4-4X (nForce4) PS2 devices not tested - may need to disable legacy USB in BIOS.
  • IDE out-of-box supported
  • USB out-of-box supported
  • Onboard Ethernet Realtek RTL8201CL 10/100 Mbps out-of-box supported
  • CLICK HERE - SATA not tested
  • Audio Realtek AC'97 ALC655 6-Channel audio w/ MIC In/Out w/at least 2-Channel out-of-box supported
  • Serial Port out-of-box detected in System Preferences under Networking
Mac OS X 10 4 8 - JaS AMD Intel SSE2 SSE3 incl PPF1 <-(Semthex 8.8.1)
NFORCE4-A939 (V1.0) (Socket 939) nForce4-single chip PS2 devices not tested - may need to disable legacy USB in BIOS.
  • IDE out-of-box supported
  • USB out-of-box supported
  • Onboard Ethernet Marvell 88E1111 Giga LAN PHY out-of-box supported
  • SATA not working
  • Realtek ALC655 6-Channel audio CODEC audio w/at least 2-Channel out-of-box supported
  • Runs perfect w/ PNY 7300GT PCI-e, full CI/QE
Almost; SATA not working, but IDE fine. Jas 10.4.8. AMD Intel SSE2 SSE3 incl PPF1 <-(Semthex 8.8.1)

eVGA

Hardware Name (socket type) Chipset Notes Fully working without patching
eVGA 123-K8-NF47-AX

(939)

nForce 4 Ultra SLI You have to disable USB Keyboard/Mouse in the BIOS for PS/2 and USB keyboard/mice to work.
  • nForce audio out working, in not tested yet.
  • ATA Works out of the box
  • SATA works with nForce4 patch.
  • USB, Firewire, PS/2 work.Marvel Gigabit LAN works out of the box, didn't even bother with nforce LAN..never used it
Jas 10.4.8 AMD.Intel.SSE2.SSE3

Foxconn

Hardware Name (socket type) Chipset Notes Fully working without patching
6100K8MA - RS / Acer FC51GM nForce 410 / 430 Audio working 2.0 mode, 5.1 is bugged. IDE works fine, SATA can be activated but will cause crash. onboard GeForce 6100 untested <<please test!>>. Onboard Ethernet does not work as described in note, using 10.4.8 AMD SSE3 test1 DVD
6150K8MD nForce 410 / 430 Audio Works with an azalia installer of the forums, onboard graphics untested, onboard ethernet works, onboard USB works. IDE works, sata untested. Using JaS 10.4.8 AMD.Intel.SSE2.SSE3.dvd
NF4SK8AA nForce 4 Ultra Sli Everything works, NForce SATA works, SiI SATA not tested Using Tubgirl 10.4.8
760GXK8MC SIS 760GX Audio AC97 ( ADI AD1888 ) Does not work , Built in Ethernet (SIS 900 ) Does not work. Onboard Graphics work , but not well. USB works fine. IDE works. Using JaS 10.4.8 AMD.Intel.SSE2.SSE3.dvd

Gigabyte

Hardware Name (socket type) Chipset Notes Fully working without patching
GA - M57SLI-S4 NForce 570 SLI(AM2) onboard audio(only tested standard, none of the surround stuff), lan, usb and firewire all work. SATA works. Read this to fix the problem with IDE drives larger than 128GB [1] Yes, Tubgirl 10.4.10 AMD SSE3 (Be patient, gray screen stays up for 5-10mins before install loads). Select the Nforce4 drivers during install
GA - M55SLI - S4 NForce 4 (AM2) audio works (no s/pdif tho), onboard network does not work(although I havn't tried to add any drivers), sata untested, usb working No, JaS Update 10.4.8 AMD SSE3 only
GA-M56S-S3 NForce 560 (AM2) Everything except Ethernet (Realtek 8211BL) works without patching, tried every driver I could find on the Internet, net card recognized, but can't get IP from DHCP. No, Kalyway 10.5.2 combo
GA - K8NXP - 9 nForce4 Ultra IDE, SATA nForce4, USB, Firewire, Audio stereo, W-LAN PCI card work. Reboot doesn't work. Not tested: SATA Silicon 10.4.8 AMD DVD SSE3 (Semthex kernel)
GA- K8N-SLI nForce4 SLI IDE, Sata Nforce4, USB, Audio stereo mic line in, reboot work, Sata work, lan work,No mark the option istall a nvidia natit driver. After installing restart and choice a safe mode e install nvidianv40.pkg. JaS 10.4.8 AMD Intel SSE2.SSE3
GA-K8NF-9 nForce4 works OOTB: IDE,nForce4 LAN,Realtek AC97 audio,USB,reboot works

works with patch: nForce4 SATA(it can even install on it with medevil patch,search forum) Not Tested: Firewire(but recognize in system)

Jas 10.4.8 AMD Intel SSE2.SSE3
GA-K8N51GMF nForce 410 works OOTB: IDE,Realtek AC97 audio,USB: nForce4 410 SATA(10.4.8 SATA not working, in Tubgirl AMD Final 10.4.9 SATA READABLE writing UNTESTED), onboard nforce lan not working, onboard video nvidia 6100 runs in VESA mode only,reboot shuts down but computer and fans still running. Not Tested: Firewire(but recognized in system profiler) Tubgirl AMD 10.4.8
GA-K8NS Nforce 3 Everything works,About this mac not working for me but who knows maybe u can figure that out.no sound/network with 10.4.6/10.4.7 all ok with 4.8 release...Not working at all Jas 10.4.8 AMD.Intel.SSE2.SSE3
GA-K8N Pro (Socket 754) Nforce 3 Default installation has video working (NO QE/CI but 1024x768), onboard Audio AC'97 (Realtek ALC658 Audio AC'97 Codec) works, onboard ethernet(Realtek 8110S Gigabit Ethernet controller)does NOT work. JaS AMD installation with SSE2 SSE3 patch off the DVD had OS X showing correct CPU speed and Ram. Jas 10.4.8 AMD.Intel.SSE2.SSE3
GA-M51GM-S2G nForce430 Works fine. I upgrade my bios with S3G file for overclocking but it doesn't matter. Audio: not fully work. Onboard network: NO. SATA: NO. Onboard Video: 1024x768. Current nitat and titan not supported. JaS 10.4.8 AMD.Intel SSE2.SSE3+ppf1.iso
GA - 945GZM - S2 Intel 945GZ Video is great with JAS 10.4.8, make sure to install the Intel 950 support. Driver for Audio, Driver for Network. IDE works perfectly, SATA works too. JaS 10.4.8 AMD Intel SSE2.SSE3+ppf1.iso + Audio + Network
GA-K8N PRO SLI F-9 nForce4 ULTRA SATA WORKS DIRECTLY , GIGABYTE 6600 ULTRA WORKS , FIREWIRE WORKS, PATA WORKS , SOUND WORKS

REBOOT WORKS ALL OUT OF THE BOX WITH TUBGIRL 10.4.9 AMD

TUBGIRL 10.4.9 AMD
GA-8S661-FXM-775 rev.1.x SiS 661FX/964L Core board works fine, but no integrated peripherals. Onboard audio: NO. Onboard network: NO. Onboard SATA: NO. Onboard USB-2: works as USB 1.1. Onboard Video: not tested. Using Radeon 9600 Pro AGP (shows as PCI), QE CI and OpenGL working out of the box, but video has some issues, must change monitor resolution using boot parameters, mouse tearing artifact, no monitor color calibration. Parallel ATA works but needs Bikedude880's patched APPLEVIAATA.kext to get full speed (it shows as SATA in System Profiler after the patch, needs flag -f at boot parameters). CPU Celeron D 351 3.2GHz shows as "Unknown CPU 3.2GHz". JaS 10.4.8 AMD.Intel SSE2.SSE3 defiant diskutil biker880 ICH7-R patch integrated.iso

MSI

Hardware Name (socket type) Chipset Notes Fully working without patching
K8N Neo3
(Socket 754)
nForce4 - 4X AMD Sempron 3000+, Socket 754, Realtek ALC656 audio works, Ethernet does not work, PATA works, GeForce 7300GT Titan + original kext Yes, AMD ISO SSE3 10.4.8, kernel 8.8.1, original 10.4.8 kexts, Titan
K8N Neo4-F
(Socket 939)
nForce4 - 4X AMD Opteron 175, Socket 939, Realtek AC97 audio works, Ethernet working with 10.4.7 IONetworkingFamily.kext + forcedeth, PATA works, PS/2 doesn't work, GeForce 7300LE Titan + original kext Yes, OSX_AMD_1048 iso, kernel 8.8.1, original 10.4.8 kexts, Titan
K8N Neo4-FI
(Socket 939)
nForce4Ultra - 4X AMD Athlon 3800+ X2, Socket 939, USB & Firewire works, Realtek AC97 audio works, Ethernet working, SATA works with nForce4 SATA patch, Shutdown works, Reboot doesn't Yes, almost perfect with OSX_AMD_1048 SSE2 SSE3 with ppf1+ppf2 iso, kernel 8.8.1 only SATA needs patching
K8N Neo4 Platinum
(Socket 939)
nForce4 Ultra AMD Athlon64 3000+, Socket 939. On-board: Realtek ALC AC97 audio, PATA, Marvell-Yukon Gigabit LAN, all work. PS2 keyboard with USB Mouse disables keyboard. Disabled USB Support in BIOS and used PS2 adapter on mouse as a temporary fix. Haven't found the right driver/hack to make them coexist yet (probably on the forums somewhere). Also, possibly due to nforce4 issues, DVD drive must be set to MASTER and target hard drive to SLAVE (mine was on other IDE channel) for the installation disc to load the Installer. In most other configurations, I was getting stuck during boot (of the DVD) with "IOATA/waiting for root" errors. Nvidia LAN, SATA, and RAID controllers not yet tested. Related components: Hawking HWP54G Wirelesss Card (with Ralink.com Mac Driver for PCI/mpci/CB RT256x/RT266x), Nvidia 6600GT (not fully tested, but functions). Yes, with mentioned tweaks and untested exceptions. Used Mac OS X 10.4.8 JAS Intel-AMD-SSE2-SSE3 with PPF1 and PPF2.
RS482M4 - IL ATI Radeon xPress200 / SB450 All works, but the network card. Firewire not yet tested JaS 10.4.8 DVD for Intel SSE3 (reseed)
K8T Neo-FSR VIA K8T800/VIA VT8297 Bios AMI 7.1 / AMD Athlon 64 2800+ (Newcastle), Socket 754 / SSE2 max, no SSE3, but Maxxus patches for SSE3 Emu on SSE2 work fine (on DVD) / Realtek 8169 GbEnet works with patch (insanelymac.org) / Realtek/VIA8297 AC'97 audio works with Azalia extra on DVD (Mic and 2ch out only) / M-Audio MobilePre USB audio (M-Audio installer from website) works excellent with full features / TexInst Firewire PCI gives full FW400 out of the box / USB 1.1 works only (not 2.0) / SATA not tested / NVIDIA GeForce FX 5200 works with Titan extra (DVD), no CG/QE, but 5200-specific installer (insanelymac.org) gives 5200 full features, including Core Graphics and Quartz Extreme - really beautiful Mostly / JaS/Semthex 8.8.1 AMD Intel Defiant 10.4.8 / Only a couple easy patches to make almost fully working - Just no USB2.0, a real problem. Run 2.0 devices through 1.1 hub and they mount ok
K8T Neo - FIS2R VIA K8T800 Bios AMI 7.1, AMD Sempron 3400+, Socket 754, Realtek 8110C ethernet works, audio Ac97 ALC655 works, USB works, SATA works, Nvidia XFX 5500 Titan + original kext Yes, AMD ISO SS2 10.4.8, kernel 8.8.1, original 10.4.8 kexts, Titan
K8N Neo2 - FX NForce3 AMD Sempron 3200+, Socket 939, all works well, SATA not tested, Nvidia FX5700 (Asus) - works fully w/Natit kexts, need to change card ID in .plist JaS AMD Intel ISO 10.4.8, kernel 8.8.1, w/Natit kexts
K8N Pro-SLI nForce4 SLI MCPs AMD Sempron 3200+, Socket 939, Everything worked (except S-ATA) out of the box, including onboard networking, and sound. Drivers for video card needs patching for Nvidia NX8800GT (MSI) but will work regardless in 1024x768 mode. Note: Did not install natively on the system (through bios and booting to the system) but it did install through VMWare to an extra hardrive, then fully booted natively after that, the kexts for video that came with it caused issues so heads up. JaS OS X 10.4.8, AMD/Intel, SSE2, SSE3 with PPF1
K9N Platinu=m nForce 570 AMD Athlon 64x2 4200, Socket AM2, GeForce 6600 works fully with Titan extensions as long as you add the device and vendor id, Buffalo WL12-PCI-G54S wireless card, SATA needs meDevil/bikedude nForce4 kext and is readonly JaS AMD Intel ISO 10.4.8, kernel 8.8.1, w/Titan kexts, needs additional kext for SATA
K9VGM-V
(Socket AM2)
VIA K8M890 AMD 64 +3800, Onboard Video (VIA Chrome9), no QE/CI, USB works, Audio needed ALC883Audio.pkg, LAN needed VIA Rhine driver, SATA works editing AppleVIAATA.kext with 0x05911106. Jas 10.4.8 AMD INTEL SSE3 SSE2, ppf1 and Deviant ppf applied, needed kexts for audio and ethernet
K8N NEO PLATINUM
(Socket 754)
nForce3 250Gb AMD Sempron64 2800, Radeon x1600pro AGP with QE/CI enabled (fast OpenGL but a bit slow Finder performance), USB works, ALC850 Audio works, integrated LAN works out of the box (Although as 100mbps, not GbLAN), SATA not tested, Firewire works. JaS 10.4.8 AMD Intel SSE2 SSE3.Defiant diskutil fix.iso, no other patch applied, fully working system

PC Chips

Hardware Name (socket type) Chipset Notes Fully working without patching
M861G(V1.6A) (Socket 754) VIA K8M800/8237 Almost everything without problems
  • Sound and SATA works fine
  • boots up with SATA HD
  • LAN is dead at first but works with VIA Rhine Driver
  • PATA works with a DVD Drive
  • USB works fine, even with USB stick
  • Change resolution this way
OSX_1048_AMD.iso

Tyan

Hardware Name (socket type) Chipset Notes Fully working without patching
[2] Tyan Thunder K8WE (S2895) Almost everything without problems
  • Only sees 2 cores
  • When 4 sticks of 1GB are installed, says 4 sticks of 8GB
  • Sound and Ethernet Work Fine
  • Does not recognize SATA
  • PATA works with HD and DVD Drive
  • USB works fine, even with USB stick
  • Change resolution this way
OSX_1048_AMD.iso (BikeRider and Medevil Patched)

Intel


Abit

Hardware Name (socket type) Chipset Notes Fully working without patching
AL8 945P/ICH7 Works : FULLY FUNTIONAL system in 30 minutes (EVERYTHING BUT ETHERNET AND SOUND NEED UPDATED AFTER INSTALL) jaS 10.4.8 AMD/INTEL Patched SSE2 SSE3
Ai7 Intel 865PE / ICH5R) Works: Everything. USB2 with developer patch, Lan 10/100, 1394, Realtek AC97 Audio I/O, SPDIF Out, MIC. SATA/PATA. ATI 9600XT QE/CI Callisto/AGPGart, OC Prescott 3.5GHz. S1 Sleep is OK JaS 10.4.8 DVD for Intel SSE3 (reseed) Semthex 8.8.1 Beta 8
IG-80 Intel 915G / ICH6 Works: Video with GMA 900 & 950 (both required) video is clean, no tearing, no artifacts QE/CI listed as unavailable (PCI-E not tested). USB with no patches (tested with 1Gb key & bluetooth), onboard ethernet does NOT yet work (listed as IC Plus IP1000 Gigabit ethernet (VEN:13f0 DEV:1023), no go so far. shows up in system profiler, ifconfig does NOT see the interface), 1394 not tested, Audio stereo only tested (Realtek AC97), SATA #1 functional (3 others not tested), PATA functional, Suspend not tested. Issues: Nothing shows on PCI bus, Realtek 8169 Ethernet is plugged in but not recognized on PCI bus, but is recognized (used RTL1xxx_1.02.pkg), will panic if plugged in or used for a bit -odd. Will update when more info is available. NOT fully functional but tested with JaS 10.4.8 DVD AMD/Intel SSE2 SSE3
IC7-G Intel 875P (MCH) / 801ER (ICH5R) Works: Everything. USB2 with USB developer patch - 261.4.2-Log, GigE Lan - Intel CSA, 1394, Realtek AC97 Audio, SATA/PATA. Minor Issues: S1 suspend only works when done manually from keyboard hook. JaS 10.4.8 DVD for Intel SSE3 (reseed)
AW9D-MAX Intel 975X Firewire,SATA&ATA work without patch.

Dual GBit ethernet & AudioMAX 7.1 works after patch. Can't use external USB2.0 Hard drives.Patches are available to fix that issue,just haven't tested them myself.

Jas 10.4.8 SSE3 Semthex 8.8.1 kernel
IL9 Pro Intel 945P/ICH7 Works with JaS 10.4.8 Intel SSE3. Onboard ethernet (Realtek) works after installing drivers from here, no onboard sound (ALC883 - detected after applying patch for ALC883Audio--Sound Works Fine after patching with Azalia driver..).
[Update: Installs fine with Jas 10.4.8 AMD INTEL SSE2.SSE3 pf1+defiant+bikedude880ICH7, but will not boot (Repeatedly shows grey screen with "Reboot your computer ..." message, no matter what config you install). Booting with -v option shows ACPI-related errors resulting in kernel panic.]
Yes, for JaS.10.4.8.Intel.SSE3
AB9 Pro Intel 965P/ICH8R Installation via VMWARE 5.5. Boot from JaS.10.4.8.Intel.SSE3 into Terminal and then run Installer from Jas 10.4.8 AMD INTEL SSE2 SSE3 pf1+defiant+bikedude880ICH7. Sound in 2 channel mode worx with ALCInject, Dual Ethernet with Realtek R1000 Patch. SATA+ATA from ICH8R and/or JMicron (IDE or AHCI) works by modifying AppleVIAATA.kext (for IDE support) or AppleAHCIPort.kext for (AHCI) and inserting dev-ids: 2363197b for JMicron, 28208086 + 28258086 for Intel ICH8R. Firewire works when USB2 is disabled in BIOS. Tough, but once configured it stays stable... No.
AW8D 975X/ICH7-R Works : Everything except Silicon Image Sata Controller
  • Sound : Audiomax ALC882M works with Taruga's Apple HDA Solution v04b
  • Lan : Dual Realtek 8111B Gigabit Lan : recognized as Built-in-Ethernet with realtek installer from here
  • usb, sata, ide, fw, all work
needs the two installers mentioned

Albatron

Hardware Name (socket type) Chipset Notes Fully working without patching
PX865PE7C Pro Intel 865PE/ICH5 If you have had this tested please edit and let us know Not tested yet
PX865PE Intel 865PE Everything works, except LAN. Get a cheap Realtek PCI LAN Card. Yes

AOpen

Hardware Name (socket type) Chipset Notes Fully working without patching
SIS-s661Fxm (s478) s661Fx Works: USB2, MIC. SATA/PATA., Prescott 3.0GHz. S1.

Not Works: Net, Audio

JaS 10.4.8 DVD for Intel SSE3 (reseed)

ASRock

Hardware Name (socket type) Chipset Notes Fully working without patching
4CoreDX90-VSTA VIA P4M900 Works with plenty of fiddling (just follow the 4CoreDual-VSTA & 775Dual-VSTA instructions): Audio (needs ALC883 installer), Network (needs this pinxue driver). VIA Chrome9 HC no Core, no Quartz 1024x768 Max. Not tested: SATA.. No, 10.4.8 (JaS AMD-Intel-SSE2-SSE3)
4CoreDual-SATA2 VIA PT880 Works out of the box: PATA, USB. Network (needs this pinxue driver). Not tested: SATA, Audio No, 10.4.8 (JaS AMD-Intel-SSE2-SSE3)
4CoreDual-VSTA VIA PT880 Works out of the box: PATA, USB. Works with easy patching: Audio (needs ALC888 installer), Network (needs this pinxue driver). Not tested: SATA No, 10.4.8 (JaS AMD-Intel-SSE2-SSE3)
775TwinsHDTV ULi 1573 Video OnBoard has not been tested since an alternate PCIX card has been used (GeForce 7300LE 256MB) and worked fine. No Onboard LAN, No Sound. USB works if USB Legacy is disabled within BIOS. Maybe editing config files using "sudo" from terminal might help get LAN and Sound. However got LAN working on installing an extra Realtek 8139 PCI card. Looking for Realtek AC 97 Audio ALC850 kext. Disk access speed very low (2MB/sec) No
775Dual - VSTA VIA PT880 Pro/Ultra Will not boot with private (original) seed, error "still waiting for boot device." Use reseed, make sure to check the VIA ULi SATA patch. Upon FIRST reboot, I installed Apple's latest USB patch, deleted extensions.mkext and extensions.kextcache, repaired disk permissions, THEN reboot. Otherwise, it will not boot again giving the "still waiting for root device error." Network patched with Rhine II driver (pinxue). Likely the same apply for 4CoreDual-VSTA. No, patched on 10.4.8 (Semthex) reseed
775i945GZ i945G Manually updated from 10.4.6 to 10.4.8 Semthex Kernel Beta 5, everything works fine, sometimes it takes a few minutes to get graphics back on after sleep mode. Mind the BIOS-settings! No patching needed
775i945GZ i945G Installed with Jas 10.4.8 disc, everything worked out of the box except from audio alc888 (just install Azalia.kext from skippyretard, no plist edition is needed but you'll get only 2 channels out, the one made especially for alc888 won't work). Everything else is working, ATA, SATA2, core 2 Duo E4300 (also tryed celeron D), video QE and CI, LAN, memory dual channel, USB2.0, event internal USB2.0. You'll get problems with midi if you try to update to jas 10.4.9 and you'll need to disable cpu limit in bios. You also will have to fix the apple file sharing. Almost, only audio.
ConRoe945G-DVi Intel 945G Everything but sound & network jack worked out of the box. See JAS install instruction for enabling the sound and the network jack. Started at 10.4.6 and updated using the Kiki Combo Updater. Got an error after installing the updater, but all was working after the reboot. NOTE: Display does not wake up after sleep (on-board video). Use 10.4.7 if it's an important feature for you.

Only the USB ports directly on the MB works. Not the ones that you connect to the pin connectors.

No
ConRoe1333-DVI/H Intel 945G Everything but sound & network worked out of the box, installed painlessly with JAS 10.4.8 SSE2/SSE3 Intel/AMD DVD, be sure to select Intel 950 graphics options. Followed instructions for network and audio under Conroe945G-DVI link (above), both work fine now. Front USB ports and dual video (VGA + DVI-D) both work. 10.4.9 hackintosh upgrade works fine with 8.9.1 kernel. 10.4.10 not tried. Won't wake from sleep. No. Requires DaemonES R1000 network drivers and manual audio kext fix (see Conroe 945G-DVI link).
ConRoe XFire-eSataII Intel 945P / ICH7R Everything works, only needs network drivers. Sound does not work. No
775i65 Intel 865G / Intel ICH5 USB, Audio (line out as output), SATA, IDE, Onboard Video (1024x768 w/o QE+CI), LAN are working well straight out of the box. Careful with AGPGart (Version 1.2 works!). Good performance (Celeron 2,66 -> 90Pts. @ XBench). Sound seems to be scratchy in videos. No
P4I65G Intel 865G / Intel ICH5 Ethernet works. USB works. Sounds works but sound enhancement must be turned off in itunes for high bit rate mp3 files to not cut out. SATA works. X-Bench Result 95.63 Jas 10.4.6 SSE2/SSE3 + Apple 10.4.8 combo + eGWan Intel.SSE3 10.4.8 combo using DaemonES 8.8.1 + 10.4.9 SSE3
P4I65G Intel 865G / Intel ICH5 Everything works (Prescott SSE3 CPU, Nvidia GFX Card). SATA and Onboard GFX untested. When installing uphuck, use : Universal Kernel 2, loginwindow patch, IOATAFamily from 10.4.8 (may be unnecesary), Remove CPUPowerManagement and RemoveThermalKexts. Add Natit 0.2 for an Nvidia Graphics Card - dual output works, which is sweet! uphuck 10.4.9 v1.3
P4VT8 VIA PT800 / 8237 southbridge With Prescott CPU : Haven't played with this too much, but i couldn't get the sound to work (this mobo seems to have a strange feature wherby the onboard sound is disabled if another device with the same PCI class - ie sound card - is present, and i couldn't be bothered to yank out my SB Live!) .ViaRhine kext didn't like the onboard ethernet. USB is also a problem (although i haven't tried the developer drivers). With these problems didn't consider it worth too much investigation. Tried a 10.4.6 release too (forget which one), but this didn't boot at all. No (10.4.8 JaS Reseed)
P4V88 VIA PT880/VT8237 Working without pacthing: SATA, USB(only 1.1, 2.0 not support), ATA. AC97 works with AppleAC97.kext fixed, dual channel. LAN works with VIARhine.kext. Very Nice Board, works perfectly with Pentium 4 CPU No, Jas Mac 10.4.8 with Semthex 8.8.1
P4VM890 VIA Northbridge Via P4M890 / Southbridge VIA VT8237R Plus / Pentium 4 2.8A Prescott (no HT) Working without pacthing: USB 2.0 fully functional, PCI-X Card NVIDIA Geforce 6200 LE supported natively (update! VGA working - DVI out not working-no dual display, in system preferences), LAN works with VIARhine.kext, no sound waiting for Realtek ALC653 patch. SATA Untested.
P4VM800 VIA Northbridge Via P4M800 / Southbridge VIA VT8237 / Intel Celeron D 315, 2266 MHz Working without pacthing: USB (2.0 not tested), LAN works with VIARhine.kext, Sound - 2 channels with patch for AppleAC97AudioVia.kext, intergraded video s3unichrome as VESA3.0 (no QE,CI). SATA Untested. PATA Maxtor 40GB ok, HL-DT-ST DVDRAM GSA-4167B ok Jas 10.4.8 SSE2/SSE3, patching needed
AM2NF3-VSTA NVIDIA® nForce3 250 Everything works. No Mac OS X 10.4.8 [JaS AMD-Intel-SSE2-SSE3 with PPF1]
775VM800 VIA P4M800
  • SATA works
  • USB works
  • Onboard sound works
  • Onboard video works at 1024x798
  • LAN works using the VIA Rhine driver
Yes, Jas 10.4.8 AMD/Intel SSE2 SSE3

Asus

Hardware Name (socket type) Chipset Notes Fully working without patching
P4B266-C (Socket 478) Intel 845D Install using JAS 10.4.8 Don't istall any audio, video, network drivers Works fully, but you need cmi8738.kext for audio and natit.kext for video card. Network works out of box.
P5VD2-MX (socket 775) VIA P4M890 VIA VT8237A Everything works perfect except SATA and Audio needs to be modified. For the VIA 8237A SATA this link worked fine. Haven't tested the JMicron Controller. For the AD 1986A Audio only this solution link seemed to work.

Haven't tested the onboard Graphic Card.

No - The SATA and Audio needs patching.
P5GPL (socket 775 Intel 915PL Motherboard worked out of the Box with JaS OS 10.4.8 Intel AMD iso. Gigabit Ethernet, USB, Audio (output only, if someone knwo a fix, please add it here). Haven't tested SATA but IDE disk works fine. Uses a Sapphire Radeon X1300 512MB card, worked out of the box with the installere, thanks to the patches included on the DVD. YES - Jas 10.4.8 with Semthex 8.8.1 kernel /no patching needed, but Output ONLY
P4VP-MX (Socket 478) VIA P4M266A JAS 10.4.8 installs and boots. During installation, only Intel package and Base Package installed. USB Mouse works, PS2 Keyboard works. Did not test integrated ProSavage Graphics Card. Audio seems to work. Network does not work out of the box but works perfect with ViaRhine.kext. System will only boot into Safe Mode if ATI Drivers for AGP installed during setup, it is advised not to install that driver in this release of OS. (Graphics card used in test system - PowerColor X1600 Pro 512MB). When in Safe Mode, sound does not work. Test System used Celeron D 330 (SSE3 support). Network needs kext installed. Sound works in normal mode, but not in Safe Mode.
P4P800 SE Intel D865 (478) Mainboard is OK, Geforec FX 5200 Ok

Lan Marvell is nothing and the same with USB Controller

YES - Jas 10.4.8 with Semthex 8.8.1 kernel / sound needs patching
P4PE Intel D845 (478) Works with ATI X1600 Pro.

Had to modify ad198x file for audio, and use a modified driver for LAN.

YES - Jas 10.4.8 Intel AMD SSE2 SSE3 / sound and lan needs patching
P5GL-MX i915GL (478) Everything works except video driver requires Diabolik GMA 900 patch.
  • Do not install GMA900 driver upon install, once its installed (res:1024*768), run Diabolik GMA 900 and then open Disk Utility and repair disk permissions.
  • Audio works wit Azalia driver bundled with the DVD.

" in my sysem ethernet is not woking/

  • 10.4.9 compo installed over 10.4.8 system crashed
No
P4S333-M SiS645 (478) Everything works except sound needs SiS 7012 AC97 driver [3]
  • Nvidia GeForce FX 5200 (CI/QE enabled) using Titan kext
  • installed Intel SSE2 patched from dvd installer
  • upgraded to Semthex 8.8.1 kernel from dvd installer
  • installed about mac fix just incase
  • Everything almost works out of the box except sound but can be easily fixed
YES - Jas 10.4.8 with Semthex 8.8.1 kernel / sound needs patching
P4C800-E i875 (478) All work (Semthex kersdfn.), LANsdf, ausdffdio in/out, Sata, Graphics card x1600pro AGP work with NeoPheus patch YES 10.4.8 DVD
P4P800 Deluxe i865PE (478) IDE, Sound All working, LAN works with Marvel Youkon Driver, SATA/RAID not tested. JaS 10.4.8 DVD SSE2/3 Intel/AMD with PPF, Semthex 8.8.1
P4S800 SiS648FX Still waiting for root device, incompatible chipset NO
P4S800D-X SIS655FX (478) Everything but the SATA (SIS 180 RAID) & onboard LAN -added PCI Intel8255. Patched Audio with [4] SIS7012.zip Also patched USB with USB DEBUG KIT 261.4.2
  • P4 2.8 HT
  • Nvidia Geforce 6800 GS OC BFG / dual head DVI-VGA 1280X1024
No, JaS 10.4.8 DVD SSE2/3 Intel/AMD with PPF1, Semthex 8.8.1 need patching & audio no input -output through input
P5P800-SE Northbridge Intel i865PE / Southbridge ICH5 Cpu is always seen as 4.0 GHz, Every component works, only for the audio output, connect speakers to the mic jack No, all components work from 10.4.6 to 10.4.8
P5P800-MX Intel 865GV chipset I am running a Celeron 2.66Ghz D, recognized no problem. Onboard Video, Onboard Sound, Onboard LAN, all working without extra patches. Haven't tested other things such as USB yet. But the most important things are working just fine. Yes, JaS 10.4.8 w/ PPF2.0
[(P4b-533-e deluxe)] Intel 845 chipset "Jas 1048 intel/amd SSE2/SSE3 ppf1+diskutil fix" USB/LAN/Firewire working, audio working with dogberts ac97 kext, highpoint raid not working Yes, JaS 10.4.8 w/ppf1 + diskutil
PTGD1-LA Northbridge Intel i915G / Southbridge ICH6 Built-in GMA900 video patched using B512's AppleIntel915.kext, some mouse tearing and artifacts still visible. Onboard sound ALC880 HD Audio patched using AppleAzaliaAudio.kext, 2 channel output only; no line-in or mic. Onboard NIC patched using AppleRTL8139Ethernet.kext JaS 10.4.8 DVD for Intel SSE3 (reseed) Semthex 8.8.1
P4P800 VM

ASUS Page

Intel 865G GMCH / ICH5 Everything seems to works smoothly, SATA, network, USB. Audio works stereo, but output jack is mic in by default but but you can fix it by modifying the file:
/System/Library/Extensions/AppleAC97Audio.kext
/Contents/PlugIns/AppleAC97CodecAD198x.kext
/Contents/Info.plist
  1. Change any one of them (ADS75 ADS74 ADS73 ADS72) to ADS70
  2. The next step is load the AppleAC97CodecAD198x.kext

With the 10.4.6 myz install disc + jaz 10.4.7 update: video with VESA 3.0 driver, no CI, no QE (no kext load, not even if editing the 830.kext). On szed as an ADP2,1 (development platform).

Yes
P5B Northbridge Intel P965 / Southbridge Intel ICH8 To install: plug a DVDreader un usb,or use a SATA DVD Driver. Turn off jmicron controller. Plug a sata HD on ich8 sata ports, and select AHCI mode in bios. After install: renable jmicron...it works for eide and sata (but not for boot) - Usb need apple patch - Audio need editing of appleazalia.kext - LAN realtek 8111 need [5] JaS 10.4.8 DVD for Intel and AMD
P5B Premium Vista Edition Northbridge Intel P965 / Southbridge Intel ICH8 2nd lan chip not working. marvel lan and audio needs patching. audio only one channel. untested yet: iremote, jmicron, firewire JaS 10.4.8 SSE3 Intel.Only.iso
P5B-E Northbridge Intel P965 / Southbridge Intel ICH8R Works: USB, Firewire, SATA
Needs Patching: Sound, JMicron PATA controller
Doesn't work: Attasic L1 LAN (How to fix this ?)
JaS 10.4.8 DVD for Intel SSE3 (reseed)
P5B-E Plus Northbridge Intel P965 / Southbridge Intel ICH8R Works: USB, Firewire, SATA (ICH8R)
Needs Patching: Sound (Refer to P5B guide), Lan Port Marvell 1Gb (Use AppleYukon Patch)
Doesn't work: Resume (Powermanagement function sleep seems to work)
JaS 10.4.8 Intel.AMD SSE2.SSE3 +PPFv1 (0ef2904e0aad1864c69b2ac67e050255)
P5B Deluxe WiFi Northbridge Intel P965 / Southbridge Intel ICH8R Works: USB, Firewire, SATA (ICH8R)
Needs Patching: Sound (Line-out only), JMicron PATA controller, One Lan Port
Doesn't work: 2nd lan port, WiFi
JaS 10.4.8 DVD for Intel SSE3 (reseed)
P5B Deluxe Northbridge Intel P965 / Southbridge Intel ICH8R Works: USB, Firewire, SATA (ICH8R)
Needs Patching: Sound (Line-out only), JMicron PATA controller, One Lan Port
Doesn't work: 2nd lan port
JaS 10.4.8 DVD for Intel SSE3 (reseed + 1st seed)
P5GPL-X Northbridge Intel 915PL / Southbridge Intel ICH6 intel gigabit lan:working natively , HD working natively on SATA or EIDE, USB:ok , audio: edit appleazalia.kext. Jas 10.4.8 intel+amd release
P5GPL-X SE Northbridge Intel 915PL / Southbridge Intel ICH6 Works: SATA and PATA, USB 2.0

Needs Patching: Gigabit Ethernet: use Marvell Yukon 88E8001 driver, Audio Out: use AppleAzaliaAudio.kext Not Working: Audio In

JaS 10.4.8 Intel.AMD SSE2.SSE3 DVD
P5GD1-VM Northbridge Intel i915G Jas 10.4.8 intel re-seed, there is a bug with install of GMA900 video drivers to get QE/CI : need to remove AppleIntelGMA950*.kext and /System/Library/Frameworks/OpenGL.Framework, then apply GMA900 drivers package from dvd again. Onboard sound work using AzaliaAudio.pkg, output channel only ; no line-in spdif or mic. JaS 10.4.8 DVD for Intel SSE3 (reseed)
P5GD2 (Socket 775) i915 / ICH6 Marvell Yukon LAN (WORKING), HD Audio (Working Mostly) with Azalia Patch on DVD (Volume control from menu doesn't work, but volume is adjustable in apps / Have not tested anything but sound out). eVGA GeForce 6600 256MB PCI-e working well with Natit Drivers. USB / SATA / IDE All Working. JaS 10.4.8 Intel.AMD SSE2.SSE3+PPFv1 + Defiant's PPFv2 DVD
P5GV-MX

ASUS page

Intel 915G Everything work with 10.4.7 GMA900 patch (for 10.4.8 or 10.4.9 I did the following [steps]here: Yes
P5GZ-MX

[6]

Intel 945GZ Everything works; Intel 950 GMA graphics work at install; Marvell Yukon LAN works with this, HD Audio (ALC883) works with this. Note that if you want to use a PCI-E graphics card instead of onboard graphics, this board only supports PCI-E x4 and a limited set of compatible cards. Yes, JaS 10.4.8 Intel.AMD SSE2.SSE3+PPFv1 + Defiant's PPFv2 DVD
P5LD2 Intel 945P / ICH7R Work: HD Sound ALC882: line-in & line-out fully supported with new AppleHDA from Taruga.

Doesn't work: SATA Ports in RAID or AHCI mode, ITE8211 ATA Ports

JaS 10.4.8 SSE3 original seed (running on 200Mhz FSB) (10.4.7 + upgrade) as well as 10.4.8 SSE3 original seed reinstall, all with kernel semthex 8.8.1
P5LD2-VM Intel 945G Everything works perfect. Sound ALC882: line-in & line-out fully supported with new AppleHDA from Taruga :) JaS 10.4.8 SSE3 reseed with kernel semthex 8.8.1
P5LD2-VM Intel 945G See above. A note about the sound: you've got a choice of line-in/line-out and dirty sound (AppleHDA) OR a clean sound with no line-in/line-out (AppleAzalia). Tested both. JaS 10.4.8 SSE3 reseed with kernel semthex 8.8.1
P5LD2-VM (socket 775) Intel 945G/ICH7 All working except red IDE port (no worries since I'm using a SATA II hard drive). Must connect DVD drive to blue IDE port. Used JaS 10.4.8 AMD/Intel SSE2 SSE3 reseed w/semtex 8.8.1 kernel. I had problems with it not loading USB drivers on boot (after 1st install), fixed after customizing installation and unchecked printer drivers and checked most common hardware. Fixed sound w/Taruga's 0.4b HDA patch. There is a full how-to guide on the Asus P5LD2-VM on insanelymac forum. This is a motherboard which you can make into a fully functional Mac. Yes, patched sound
P5LD2-VM Intel 945G / ICH-7 Works right out of the box. E-IDE does not work. Set BIOS Correctly for GbE LAN to Work properly. ALC882 Fix with Taruga HDA patch V.04. Refer to the Asus P5LD2-VM How-To Guide in the Genius Bar. JaS 10.4.8 SSE3.Intel Only.iso or JaS 10.4.8 AMD/Intel SSe2.SSe3.v2.iso
P5LD2-VM DH Intel 945G / ICH7 (DH) BIOS version:0602 Work: Everything work with 10.4.8 Jas install DVD/semthex kernel. HD Audio (Realtek 882) working with this guide (line out (2 channels), spdif (digital out), line in, mic in). Doesn't work: SATA Ports in RAID or AHCI mode, ITE8211 ATA Ports Yes -sound needs patch
P5LD2-VM SE

ASUS page

Intel 945G Everything work with 10.4.8 Jas install DVD/mifki kernel (sata,network,gma950 all work straight out the box, NOTE this is the SE "no raid" board - sound requires modified appleHDA.kext gives line out, spdif (digital out), line in, mic in Yes -sound needs patch
P5L-VM 1394 Intel 945G / Intel ICH7 Work: Everything works except for Attansic ethernet chip. HD Audio (Realtek 883) only 2 channels working with some modifications (ALC883) you need to follow this guide.

Doesn't work: line in, ADD2 card

JaS 10.4.8 SSE3 reseed with kernel mifki 8.8.1
P5L-MX Intel 945G As with P5L-VM, everything works (SATA, USB, IDE) except for the Attansic ethernet chip. Note: you need an IDE HD connected to boot the JaS DVD, otherwise you get "Still waiting for root device". (Note this is fixed with the ICH7/ICH8 biker880 ppf). Analog Devices/Intel HD Audio (AD1986A) works on 2 channels out with Vendor and Device ID edit in AppleAzaliaAudio.kext. Procedure here. PCI-IDs Ven:11d4 Dev:1986 (Soundmax 1986) and Dev:27d8 Ven:8086 (Intel ICH7 HD Audio Controller). Follow the usual AC97 guide to have it working. No mic. Sound out on back panel only. GMA950 works on this board with QE+CI (Install JaS package from 10.4.8 DVD. JaS 10.4.8 with mifki or semthex 8.8.1 Kernel
P5PE-VM i865G (775) Fully working except onboard LAN, which needs skge.kext, sound on mic jack 10.4.8 DVD
P5V800-MX Northbridge VIA P4M800 / Southbridge VIA VT8251 Works: Video VGA and network (Realtek PHY adapter in chipset) after installing ViaRhine driver USB No Longer Broken In 10.4.9 SSE3

Doesn't work: remaining Southbridge facilities: no sound, no SATA

JaS 10.4.8 DVD for Intel SSE3 (reseed)
P5VDC-X Northbridge VIA P4M880 Ultra / Southbridge VIA VT8237A Works: Network after installing ViaRhine driver,USB works out of the box.
Doesn't work: Sound, SATA(Can be realised by editing AppleVIAATA.kext and adding device ID) as far as I can see there is no AGP accelleration
JaS 10.4.8 DVD for Intel SSE3 (reseed)with Semthex kernel and Loginwindow patch
P5VDC-MX Northbridge VIA P4M800 PRO / Southbridge VIA VT8251 Works: Network after installing ViaRhine driver, USB works after installing this driver.
Edit AppleVIAATA.kext using ID:0x33491106 for full SATA support
(still) doesn't work: Sound (AC97 VT8233 ALC655)
JaS 10.4.8 DVD AMD Intel SSE2 SSE3
P5WD2 Northbridge Intel P955x / Southbridge Intel ICH7R
  • Works: Dual Core Pentium D, USB 2.0, PATA, SATA
  • Needs Patching: ALC882 Sound (works with ALC882_AppleHDA_v0.4b.mpkg.zip), Marvell Yukon 8001 LAN card (works with skge.kext.zip - unzip, copy to /System/Library/Extensions/ and reboot.)
  • Not working: PS/2 connectors. Have to use USB KBD and mouse.
JaS 10.4.8 Intel/AMD SSE2/SSE3 PPF1 PPF2, semthex:/nebukadnezar kernel from Dec 9, 2006, LoginWindow patch.
P5WD2 - Premium Northbridge Intel P955x / Southbridge Intel ICH7R Works: USB, Firewire, SATA

Needs Patching: Sound, Doesn't work: Marvelle Lan, reading of sensors other than on HD for temp

JaS 10.4.8 DVD for Intel SSE3 w/semthex
P5W DH Deluxe Intel 975X / ICH7R Work: Everything works perfect. HD Audio (Realtek 882) all function with ALC AppleHda v 0.4 digital out in and mic line OK.

JaS 10.4.8 DVD for Intel SSE3 w/semthex. And probe 10.4.10 koolkal 10.4.10 combo update intel sse3 and very good function all. with 10.4.10 audio install applehda and AC97 in package kool and reinstall applehda v 0.4. (koolkal 10.4.10 combo update intel sse3 only.mpkg.zip). Wireless (RTL 8187) Doesn't work: Remote. webcams whith macam driver.

Jas install DVD 10.4.8 SSE 3,see Installed ALC882_AppleHDA_v0.4b.mpkg.zip
P5W DH Deluxe Intel 975X / ICH7R Everything works, except sleep. Out of the box I didn't got sound and NIC, but replaced the AppleNetworkingFamily kext with a 10.4.7 version. Audio works with 2 channels and mic + headphones (front) and line-in. Used Jas install DVD 10.4.8 SSE3 + Semthex 8.8.1 Beta 8
P5W64 WS Intel 975x / ICH7R Everything works, except stand-by (it goes to sleep, but it doesn't wake up - reboot required).
  • Lan Marvell Yukon 8052 working with modified Yukon.kext
  • Lan Marvell Yukon 8001 working with skge.kext
  • Integrated Audio working with modified AppleAzaliaAudio.kext copied in Extensions directory, modified ID for ADI1988b and modified ID for ICH7 soutbridge (original ICH6)
Jas 10.4.8 with Samthex 8.8.1 Kernel
P5WDG2 - WS 975x Audio working but it is scratchy, follow the guide, could not get Marvell ethernet drivers to work but I've read that other people have successfully used it in previous builds. Yes JaS Update 10.4.8
P5N-E SLI Nvidia nForce 650i SLI Everything works expect for Ethernet. SATA untest but shows up in system info. Reboot does not work. HD Audio fully works after applying [ALC883Audio.mpkg patch ][IMPORTANT: you have to select Costomize and choose 3ports_digital or else you going to screw it up!]

EVGA Geforce 7900GS work perfect with Macvidia driver. D-Link DGE-530T PCI Gigabit LAN works after applying the [skge.kext patch] and edit info.plist with 0x4C001186.

Jas 10.4.8 SEE2/SEE3 Intel AMD DVD with Semthex kernel 8.8.1
P5N32-SLI Premium Nvidia nForce 590 SLI Everything works expect for Ethernet and SATA. Reboot does not work. On-board audio works with ASUS driver.

Geforce 7600GT work perfect.

Jas 10.4.8 SEE2/SEE3 Intel AMD DVD

Biostar

Hardware Name (socket type) Chipset Notes Fully working without patching
915P-A7 Combo Intel 915P Audio full supported without patching, Ethernet need patching, video full supported with Natit Driver (7300 GT) JaS 10.4cccd.8 DVD for Intel SSE3
T-Force 965PT Intel 965 Everything Works W/ Minor Editing No, JaS 10.4.8 DVD
945GZ Micro 775 Intel 945 Everything Works W/ Minor Editing No, JaS 10.4.8 DVD
945G Micro 775 SE Intel 945 GMA950 video, LAN, USB2 (front too), SATA, PATA worked out of the box. PS2 was not working at time of install, have not tried to fix. JaS 10.4.8 DVD, netkas, PascalW 10.4.10 update. Full sound worked easily by duplicating ICH6 section of /System/Library/Extensions/AppleAC97Audio.kext/Plugins/AppleAC97AudioIntelICH.kext/Contents/Info.plist and changing key to "ICH7 AC97 Audio", ICH Type to "7", and IOPCIPrimaryMatch to "0x27de8086". "27de" is the device ID for ICH7. Need a SPDIF header, but SPDIF appears in Sound preferences so I think it will work. My E4400 OCs to 2.6ish with stock Vcore on this board.
945P A7A Intel 945 Everything Works W/ Minor Editing (everything but audio out of the box, audio needs patched AppleAC97Audio.kext) No, JaS 10.4.8 DVD
U8668d Ver 7.A Via VT8751 Apollo P4M266 No Works. Still Waiting for root device. No, JaS 10.4.8 DVD

DFI

Hardware Name (socket type) Chipset Notes Fully working without patching
INFINITY 975X/G Northbridge Intel 975X / Southbridge Intel ICH7R Realtek HD audio works fine (with AppleHDA patch) with minor dropouts but I believe this was due to several thing happening whilst playing the music. Gigabit ethernet fully working (with realtek driver). USB fully working. firewire & video port not tested. JAS 10.4.8, SSE2 SSE3 Intel and AMD, Semthex 8.8.1 kernel
LANPARTY PRO 875B Intel 875P Chipset Tested with P4 2.6Ghz HT 800FSB SSE2, ATI AIW X800XT 8X AGP. Audio works. AGP works. ATA, SATA, USB all work. Intel 82547EI Gigabit LAN works. Firewire & MIDI Port not tested. RAID should work, but not tested. uphuck 10.4.9 v1.2 or v1.3 Installation DVD (universal Intel/AMD x86) (uphuck.com) Remove CPUPowerManagement kext for nophet, sse2, or amd cpu (included setup option).

ECS

Hardware Name (socket type) Chipset Notes Fully working without patching
P4M800 PRO-M Version 2.0 Via P4M800Pro / VT8237R LAN works with pinxues Viarhine.kext. Sound and USB 1.0 work natively, but installing patch on Jas 10.4.8 for USB 2.0 seems to break it. PATA & SATA work. Has some issues with multiple partitions. Had some issues with root device not found error, but -f will boot. Sound doesn't work in safe mode. Sound out was only in the left speaker, but works perfectly with Realtek ALC655 patched kext. Haven't tested line-in. For some reason USB audio devices (Logitech headphones & iMic) will randomly give off garbled sound. Geforce 7800GS,6200 & 5500 work with titan.kext QE and CI supported. PCI works fine. No, JaS 10.4.8 DVD for Intel SSE3 (reseed) - Currently running 10.4.9 with the latest version (4/24/07) of the koolkal 8.9.1 kernel. Previous kernel revisions wouldn't boot past BIOS.
865PE-A Intel 865PE Audio working (only line out and mic tested), usb working, onboard network working, IDE working, sata untested Almost,R8139 kext from JaS 10.4.7 DVD for network
915P-A v1.2 [7] Intel 915P + ICH6
  • PS2 out-of-box supported (even cheap keyboard with power button works perfect.
  • IDE & S-ATA out-of-box supported
  • USB & USB2 out-of-box supported
  • Onboard Ethernet Realtek RTL8110S 10/100/1000 Mbps. It should work in 10/100base as it worked with ALL previous versions that I tested but alas it doesn't.
  • Audio C-Media CMI9880 8-Channel audio: Only 2-Channel out-of-box supported
  • DVD burning tested with ATA-burner
Mac OS X 10 4 8 - JaS Intel SSE3. LAN-card needs the RTL1xxx_1.02.pkg for 10/100base. No Gigabit-Lan speeds.
945P-A 1.0 Intel 945P Ethernet, USB, SATA, IDE work without patching. Haven't been able to get ALC880 audio working even with patches. Tested with JaS 10.4.7 Intel Only SSE2/SSE3 and JaS 10.4.8 Intel/AMD SSE2/SSE3. Almost - no audio
945GZT-M Intel® 945GZ & ICH7 LAN Works, on board video works, sound works with skippyretards HD Audio drivers, SATA Will work as well. Installed with

Mac OS X 10.4.8 [JaS AMD-Intel-SSE2-SSE3 with PPF1 & PPF2 and everything worked out of the box except the audio which was very easy to install. Also the upgrade to 10.4.9 using the latest walk through here on the wiki worked great.

Audio needs to be patched but that's it.
P4M890T-M2 Via P4M890 / VT8237R LAN works with pinxues Viarhine.kext. Sound and USB 1.0 work natively, but installing patch on Jas 10.4.8 for USB 2.0 seems to break it. PATA & SATA work. Has some issues with multiple partitions. Had some issues with root device not found error, but -f will boot. Sound doesn't work in safe mode. Sound out was only in the left speaker, but works perfectly with Realtek ALC655 patched kext.. Geforce 7300GT works with titan.kext QE and CI supported. PCI works fine. Will not work with BIOS firmware newer than the October 2006 version. Mac OS X 10.4.8 [JaS AMD-Intel-SSE2-SSE3 with PPF1 & PPF2 and everything worked out of the box except the audio and LAN
nForce 570 SLIT-A nforce 4 Lan works with forcedeth if you patch his .plist to inlcude your device id (026910DE), Realtek 883 works with patch found on mac forum. SATA works after you install MeDevils nforce4 SATA patch, so install on an IDE first. Boots first time with the 10.4.8 PPF1 and PPF2 JaS dvd. nVidia 7900 GS KO works perfectly, both displays. SATA, audio, and LAN need to be patched
PT890T-A V1.0 VIA PT890/8237S LAN works with pinxues Viarhine.kext. USB works natively but there seems to be a problem if too many devices at once or a flashdrive in slot at boot. Add devices after boot ..one at a time and wait for recognition. PATA works, but I haven't tried SATA. Unable to get MB sound working, but CT4810 SB card works with Tubgirl disk. Had to use USB sound with JAS disk. Geforce 7300LE works with titan.kext QE and CI supported. Haven't tried tv out. PCI works fine. Mac OS X 10.4.9 (Tubgirl AMD 10.4.8. patched with PPF for 9) and JAS 10.4.8 SSE2 and SSE v3. Everything worked except sound and net out of the box.

Epox

Hardware Name (socket type) Chipset Notes Fully working without patching
915P Epox Ep-5EDAI Intel 915P Audio full supported without patching, Ethernet need patching JaS 10.4cccd.8 DVD for Intel SSE3
Intel 915 Everything Works W/ Network has Problems JaS 10.4.8 DVD
EP-5ELA3I (775) Intel 915PL Audio & network supported without patching. SATA, ATA, USB work too. JAS 10.4.8, SSE2 SSE3 Intel and AMD
EP-5EPA+ (775) Intel 915G SATA, ATA, USB, Audio worked out of the box. Network needed 88E8001 patch to work. JaS 10.4.8 SSE/SSE3/Intel&AMD

eVGA

Hardware Name (socket type) Chipset Notes Fully working without patching
680i SLI socket 775 nForce 680i SLI Audio working via AzaliaAudio.pkg.zip (2channel out), IDE/USB/Firewire works natively; no SATA, no ethernet (will try nforce4sata; punted on ethernet and bought a linksys LNE100TX add-in card w/tulip drivers) (Make sure to install titan or you will get screen that promotes you to reset your computer) JaS DVD 10.4.8 (SSE2/SSE3/PPF1/PPF2) (had unable to find root device issues with earlier JaS 10.4.8 release)

Foxconn

Hardware Name (socket type) Chipset Notes Fully working without patching
865G7MF-SH Socket 775 Intel 865G Audio and Ethernet working, SATA Support not tested JaS DVD 10.4.8
945G7MC-KS2HV Intel 945G Chiset/ GM950 video/ Realtek HDA Audio
  • Install method: TOH 10.4.8
  • Video onboard works fast and perfectily
  • Audio does not work (needs patch)
  • LAN: does not work
  • IDE works fine with CD and DVD
  • SATA not tested
  • I used offboard USB audio (c-media) and d-link USB wifi adapter
  • TOH 10.4.8 install DVD
  • Just video

Gigabyte

Hardware Name (socket type) Chipset Notes Fully working without patching
GA-965GM-S2 Intel G965 ICH8 Uncheck everything except Intel patches Then use the Natit drivers for video, and these instructions for network card and sound. For walk through. JaS 10.4.8 AMD Intel SSE2.SSE3
GA-965P-S3 rev 1.0 Intel i965 ICH8 Using F8 BIOS & non-semthex 8.8.1 kernel. Tested/Working: IDE, SATA0/1(Purple), AHCI0/1 (Orange), USB1.1/2.0, GBEthernet, ALC883 Multichannel Audio (analog) - up to 7.1/Mic/Line-In Not Working: AHCI4/5 (Orange). Installed with USB2.0 DVD drive, very fast, very stable. For more info, visit this step-by-step guide. JaS 10.4.8 AMD Intel SSE2.SSE3 (patched with ppf1 & defiant disk utility patch)
GA - 8I848P-G Intel 848P MCH / ICH 5 SATA works.LAN drivers are included in Myzar releases. Audio works. HDD works on pata.USB works. Myzar 10.4.8 AMD Final
GA-945GZM-S2 Intel 945GZ / ICH7 Everything works! Out of the box: SATA,ATA,USB work, GMA950 works with QE/CI. Don't install anything extra from the DVD, you're asking for kernel panic!

Network needs this driver (here's the thread) Sound is fully working with skippyretard's AzaliaAudio883.pkg - use the 6 port custom install!

JaS OS X 10.4.8 (AMD-Intel-SSE2-SSE3 with PPF1) + network + audio
GA - 8I945GZME - RH Intel 945 / ICH 7 Semthex Kernel: SATA,ATA,USB work, GMA950 grapihc chip works with QE/CI supported! 2 channel Audio works after applying this hack Fixed, just change 882 to 883. LAN works after recompiling skge driver 8001 kext.

Full Walkthrough for 10.4.8 install here [8]

JaS 10.4.8 Install with Semthex Kernel then upgraded to latest Semthex Nebukadnezar Kernel
GA - 8I945GMH - RH Intel 945 / ICH 7 Everything works except shutdown/restart problem. Audio not tested. Bios sata settings- avoid 'AHCI'. Hotiso 10.4.6 upgraded with 10.4.8 for intel
GA - 8I945GMF Intel 945 / ICH 7 SATA 2, ATA, USB 2.0, Fireware , Video GMA950 works with Quartz Extreme and OpenGL, (Line In / Line Out / MIC In / SPDF Audio works after applying this hack ONLY Kernel 8.8.1), LAN works JaS 10.4.8 Kernel 8.8.1
GA - 8I945P - G Intel 945P / ICH 7 SATA Worked, Audio Worked After use AppleHDA 0.4b Driver, Broadcom 5789 Gigabit Ethernet Controller can work after use the kext that modified Dev id of "AppleBCM5751Ethernet.kext", But cannot recongize the MAC Address. USB is OK, IT8212 ATA/RAID Controller cannot work JaS 10.4.8 Intel SSE3 Only
GA - 945P - S3 Intel 945P / ICH7 Core 2 Duo E6400/1GB/SATA HD...First attempt installed, but then yielded an unbootable system ("unrecognized platform: ACPI" halt w/ restart msg). Second attempt, only installed the AzaliaAudio extra driver and it booted OK. No audio or Ethernet, but RTL1xxx and ALC883Audio worked fine. Also, latest NATIT worked fine w/ my GeForce 7300 GS PCI-E card w/ full CI/QE support. Seems to run GREAT! "JaS 10.4.8 AMD INTEL SSE2 SSE3 beta 2" DVD w/ semthex 8.8.1 and extra drivers (Azalia, NATIT, etc.)
GA - 945G - S3 Intel 945G / ICH7 Pentium Dual Core E2160/1GB/SATA HD, ALC883 audio working, Realtek 8111 Gigabit ethernet working, GMA950 working QE/CI &res change. needs "-legacy" key for recognizing SATA HDD during installation. Dual booting with Chain0 "10.4.9 uphuck v1.3" DVD w/ 8.9.1 kernel
GA - 965P - DS3 Intel 965P Everything works, more information here

demonoid has a patch for Jas 10.4.8 reseed to fix IDE on install disc. Search for "jmb" (no quotes) and it should come up on demonoid

JaS 10.4.8 DVD reseed + pion's package
GA- 965P - S3 Intel P965 Core 2 Duo 6600. Everything installed fine (Using DVD-ROM hooked up via USB). Followed instructions for Western Digital SATAII Drive. Had trouble getting Ethernet running, but fixed with simple file edit. Pion's System profiler fix works after running a second time. JaS 10.4.8 DVD w/ JMicron patch, Pion's Patch, Prasis Kernel Update
GA - 965P - DS3 Intel 965P Everything works, more information here JaS 10.4.8 DVD reseed + pion's package
GA - 965P - DS3P Intel 965Pe Same issues as the DS3 and same fixes. Works fine once patched, USB, Firewire, audio. JaS 10.4.8 DVD + pion
GA - 965P - DS4 Intel 965P Everything works, CPU:Intel Core 2 duo 6300; Graphics:PowerColor X1600 PRO; Display:DELL 2007WFP Harddisk:WDC800JD-75MSA1;DVD-ROM:PIONEER DVD-127P:MERMORY:A-DATA Vitesta DDR2-800...more information here JaS 10.4.8 DVD reseed + OSX 10.4.8 Jmicron JMB IDE patch + AppleHDA Solution(ALC833) + pion's package
GA - 965P - DQ6 Intel 965P Everything works apart from sound works out of the box with JaS 10.4.8 DVDv1, install ALC888 patch and select 6 channel (not digital). BIOS setup Jas 10.4.8 DVDv1 + ALC888
GA - 8VT880P Combo VIA PT880P Everything seems to work (LAN, USB, SATA *fix, IDE, Audio,USB working, use v 256.4.2* Yes JaS Update 10.4.8
GA - 945GM - S2 Intel 945 / ICH 7 installed via VMware, native install needs "-legacy" boot arg. everything works fine, DDR2 800 PC6400 is seen as "RAM 133Mhz"... Apple original security update (12/2006) works fine without patching. OnBoard audio fixed with ALC883 patch from here TubGirl AMD SSE3 test1 PPF2 DVD
GA - 865PE 1-st rev. Intel 865 Sound, USB without patching. SATA/RAID not tested. JaS 10.4.8 DVD on Semthex 8.8.1
GA - 8IPE 1000 - G rev.4.x Intel 865PE Intel SSE3 package.Sound working in stereo only (disable top performance in bios if the sound is intermitent), Ethernet working with DaemonES' drivers, USB + SATA fully working. Can also be patched with Jas 10.4.9 update JaS OS X 10.4.8 (AMD-Intel-SSE2-SSE3 with PPF1 & PPF2)
GA-8S661-FXM-775 rev.1.x SiS 661FX/964L Intel SSE3 package. Sound does not work, Ethernet does not work, USB works as 1.1, SATA is not recognized, PATA works but needs Bikedude's patched APPLEVIAATA.kext to get full speed. JaS OS X 10.4.8 (AMD-Intel-SSE2-SSE3 with PPF1 & PPF2)
P35-DS3R Intel P35 ICH9 driver not disponible, but able to use disks on it, JMicron patch works, sound ACL889B is not disponible at the moment. Ethernet RTL 8168/8111 works with modified kext and RTL1xxx driver but you need to enable Wake On Lan on bios or windows drivers. uphuck OS X 10.4.9
GA-8I865GME-775 Intel 865G Sound, USB, SATA worked out of the box. Lan needed to add VID/PID to AppleIntel8225x.kext. Using ATI9600Pro with Callisto008. Updated to 10.4.9 using JaS from same package and 10.4.10 from TPB. JaS OS X 10.4.8 (AMD-Intel-SSE2-SSE3 with PPF1 & PPF2)
Powered by MediaWiki © 2015 OSx86 Project  |   InsanelyMac  |   Forum  |   OSx86 Wiki  |   PHP hosting by CatN  |   Designed by Ed Gain   |   Privacy policy   |   About OSx86   |   Disclaimers