OSx86:HCL 10.6.8

macOS 10.6.8 Hardware Compatibility Portable Computers Desktop Computers Hardware Components

This is a component level hardware compatibility list. We want to keep it as accurate as possible, but please, do not entirely rely on this list when buying hardware. Add which parts you have working in the categories listed below, or create a new category. Please keep alphabetical order inside the categories. The categories themselves are ordered by popularity. Please list any caveats or problems as well.

• ONLY add hardware that you have TESTED. Don't add hardware just because you think it might work.
• Please add hardware into tables.
• This is for 10.6.8 builds only.

For how to edit the Wiki, please see this thread. Thank you!

You're looking for an Installation guide? see here

Note: For suggestions about table headings, please join the discussion here.

Motherboards

Asrock

Hardware Name	Chipset	Notes	Patches	32/64bit working with patches
ConRoe1333-DVI/H	Intel® 945G Chipset-ICH7	System Configuration: Intel E6750 CPU 2,60 GHz @ Overclocking 3,20 GHz ATI Radeon™ HD6670 (1024MB DDR5) works fully with PCI-E/ATI Kit DDR2 2GB (2x1) 834 MHz Ram OCZ Platinum Rev.2 Timing 4-4-4-15 Install Method: RETAIL Disk Image (USB Image) by MASTRI81 Components Status: Audio ALC888 work only OUT Ethernet - Native Works (Realtek RTL8111B) USB 2.0 - Native all Work USB 3.0 PCIe (LACIE) - Native all Work SUPER SPEED IDE - Native all Work Shutdown/Reboot - Work (Stop Work_Kext SleepEnabler x64) Everything Installed in a Mac G5 Power Case mod. by MASTRI81	Patches Kext Used: Fakesmc, NullCPUPowerManagement, OpenHaltRestart, SleepEnabler. PRIVATE Full kext edited by MASTRI81 Tools Link Kext Helper B7
880G Pro3	AMD 880G / SB850	on board sound does not work, on board graphics does not support QE/CI -- use peripheral. System Configuration: Motherboard: ASRock 880G Pro3 BIOS: latest CPU: AMD Phenom II X4 955 BE 3.2GHz Video: ATI Radeon HD 5770 1GB GDDR5 Audio: Turtle Beach Audio Advantage Amigo II USB RAM: CORSAIR Vengeance DDR3 1600MHz 8GB (2x4GB) HD: Crucial 64GB SSD	Nawcom Mod Boot CD+ Retail Snow Leo DVD with custom options legacy kernel, AppleATIATA, [no sleep, no graphics, lan or audio] ==> 10.6.8 Combo Update (install andy's kernel before reboot), Atheros L1cEthernet, chameleon w/bootflags "arch=i386 -force64" graphics enabler=y, andy's mach kernel
A3M785GMH/128M	AMD 785G / SB710	not all works but still working on it	Kalyway AMD Patch 1	?	?
AOD790GX/128M	AMD 790GX / SB750	Sleep does not work, everything else works fine. (OnBoard HD3300 native Screen, Resolution Settings are Limited no Video Support. Ethernet, SATA, USB & Sound (Voodoo HDA) Worked out of the Box System Configuration: Motherboard: ASRock AOD790GX/128M (MacOsX shows as 2.79GHz Quad-Core Intel Xeon) BIOS: latest CPU: AMD Phenom II x2 550 @ AMD Phenom II x4 B50 (Bios UnLocked Cores 100% Stable) Video: OnBoard ATI Radeon HD3300 512MB DVI RAM: G.Skill DDR2 800MHz 4GB (2x2GB), Kingston DDR2 800MHz 1GB (Mac OS X shows as DDR2 200MHz) HD: Samsung HD502HJ 500GB	Legacy Kernel 10.8, AMD Binaries (dyld cache und libsystemB.dyld +Xcode dylds), -force64, Nawcom Mod Boot CD+ Retail Snow Leo DVD + 10.6.8 Combo Update
X58 Extreme	Intel X58	Sleep does not work and often restarts instead of shutting down. Everything else works fine.	Ethernet RTL81XX, AppleHDA Rollback + ALC8XXHDA. SATA working OOB, as well as graphics (installed with iBoot method)
H61M-VS	Intel H61	Finder behaves erratically after wake-up from sleep. Onboard Audio and Integrated Graphics not tested. Everything else works fine. System Configuration: Pentium G620 2 x 4GB 1333MHz DDR3 (Apacer 78.B1GDE.9LZ0C) Nvidia 8800GT 512MB Intel 320 40GB SSD WD15EARS HDD E-MU 0202 USB Audio Interface	MyHack 2.0 RC1, AtherosL1cEthernet.kext	Yes	?
G31M-S R2.0	Intel G31	Sleep does not work, everything else works fine.	Ethernet RTL81XX, Voodoo HDA 0.2.1 (Tutorial: http://www.youtube.com/watch?v=MgtvSmo2O-4)
Extreme3 Gen3 Z68	Z68	Built from Retail OS 10.6.0 disk + iBoot. Had issues booting to install. ended up using -v -x GraphicsEnabler=No PciRoot=1 (Had a HD6850 during install). Sleep does not work.	[Realtek ALC8xxHDA / AppleHDA RollBack/ Non-DSDT 892] [Network - Realtek gig ethernet 2.0.6] [Chimera boot loader][boot flags used in install step was added to boot options in multibeast. Used standard multi-update to 10.6.8.	?
Extreme4 Z68	Z68	System Configuration: Motherboard: Z68 Extreme4 BIOS: 1.70 (latest) CPU: Intel Core i7-2600K (undervolted 100% Stable) Video: ATI Radeon 4850 512MB DVI (10029442) RAM: 16GB 4x4Team Group Team--Elite-1333 (Mac OS X shows correct) HD: SSD OCZ Solid 3 60GB Audio: C-Media CM8738 (Theatron Agrippa DTS 7.1 - Club3D) (13F60111) (Onboard Audio disabled) Lan: Broadcom Netlink BCM57781 Gigabit Ethernet (14e416b1)	->Sandy Bridge is supported from 10.6.8<- Install Mac SL with USB-Stick. Create the Stick with OSX86 ModUSB pkg and Retail Snow Leo DVD 10.6.3. Install Snow Leo, install Chimera/Chameleon, install UpdateHelper and Reboot. Start from USB again, install Combo Update 10.6.8 Boot from HDD and install Driver. USB3 works, but unstable yet.	?

Asus

Hardware Name	Chipset	Notes	Patches Used	32/64bit working with patches
ASUS M4A88T-V EVO/USB3	AMD 880G / AMD SB710	System Configuration Audio: Realtek ALC892 with AppleAzailaAudio.kext (I'll certainly edit this if I find a better solution.) LAN: Realtek 8111E Gigabit Ethernet: use Lnx2Mac's RTL8XXX Ethernet driver. SATA: Works fine without any patches in AHCI mode. HDD: Varies, but it's some SATA HDD. IDE: Haven't found a kext for it. USB: Works just fine out of the box. I don't have any USB3 devices, so I don't know whether the USB3 ports work at full speed. ODD: LG HL-DT-ST DVDRAM GH24LS50 (Lightscribe untested). Card Reader: Rosewill 2.5" internal USB Card Reader works perfectly as a USB mass storage device. Shutdown and reboot work. I haven't attempted to get sleep working. CPU: 3.0 GHz AMD Athlon II x4 640. Video Card: XFX ATI Radeon 5670 1GB with 1 DVI Monitor at 1920x1080 works with GraphicsEnabler=Yes. RAM: 12GB DDR3 1333Mhz (2x2Gb, 2x4Gb). OS: Mac OS X 10.6.8 Snow Leopard. Bootloader: Chameleon. Installation Install with Nawcom's ModCD (or ModUSB) and the 10.6.3 retail disc (10.6.0 would probably work as well, but I haven't tried it.) with the following "CUSTOM OPTIONS": (Don't worry if the installer claims that it failed) Legacy Kernel Audio AppleAzailaAudio Boot into your fresh installation with the ModCD (or ModUSB) because no bootloader is installed on your hard drive yet. Install the 10.6.8 Update Combo v1.1 and AnV's Legacy Kernel 10.8.0. When the Combo Update's installer is prompting you to reboot, force it to quit from the Apple Menu and then install the Legacy Kernel. Install the latest Chameleon. Reboot with -force64 -v and install amd_insn_patcher if you have more than 4GB of RAM. Follow the neccessary steps to get your graphics card working. (GraphicsEnabler=Yes, ATY_Init.kext, etc.) Enjoy!	Kexts/Patches AppleAzaliaAudio.kext. Remove and backup AppleHDA.kext before installation. amd_insn_patcher. Only needed if you have 4+ GB of RAM. You may also use the flag maxmem=4096 with the obvious effect that only 4GBs of RAM will be visible to OS X. AnV's legacy kernel 10.8.0 Chameleon Other There's a slightly upgraded version of this motherboard that supports AM3+ called the M5A88-V EVO which looks so similar to this one that it would probably work too. The built-in ATI Radeon HD 4200 is not supported. Boot Flags -force64 arch=i386
Rampage Formular	Intel X48 / Intel ICH9R	System Configuration: Install Method: iATKOS S3 v2 (10.6.3) Motherboard: Asus Rampage Formular BIOS: Rampage Formula 1001 CPU: Intel E8400 3,0 GHz Video: ATI Radeon HD5450 512MB DDR3, VGA, DVI, HDMI, lite retail (11166-01-20R) works fully after Combo Update -> 10.6.8 RAM: Corsair DDR2 4GB (2x2GB) TWIN2X4096-6400C4DHX HD: Samsung Spinpoint 750GB Components Status: Audio - (SupremeFX II / AD1988B) (deselect both Audio Options / Kernel Panic) -> HDEF and AD1988B patches to DSDT + AD1988BFix.kext Ethernet - Select (Marvell Yukon Gigabit 88E8056 ) USB 2.0 - Native Support IDE - Select JMicron SATA/IDE CPU - Speedstep -> Select (Voodo Power not -> Voodo P-State -> Kernel Panic) Firewire: Native Support SATA 3GB - Native Support Video - Graphics Enabler= no / ATI Activator= no / no additional selection under iATKOS S3 v2 / full resolution 1920 x 1200 / VGA & HDMI Dual Screen Keyboard - if PS2 -> Spacebar Start - Select -> Voodo PS/2 Post Install: Combo Update Mac OS X 10.6.8 v1.1 [1] After Update an *halt* may occur , start with -x -v , afterwards no further problems
P5W DH Deluxe	Intel 975X Intel ICH7R	System Configuration: Intel E6400 CPU 2,13 GHz @ Overclocking 2,67 GHz, FSB 1333 Mhz, BUS 333 Mhz ATI Radeon™ X1800XT (256MB DDR3 256Bit) works fully with PCI-E/ATI Kit DDR2 4GB (4x1) 834 MHz Ram OCZ Platinum Rev.2 Timing 4-4-4-15 Install Method: RETAIL Disk Image (USB Image) boot_Private ((( KEXT-GUIDE ))) edited by PIEROF81 Components Status: Audio ALC882M Stereo L+R - Line-Out x3 24bit, Line-In x1 20bit, Integrated microphone x1 20bit, Headphones Integrated x1 24bit, S/PDIF out x1 32bit Ethernet - Native Works (Marvell Yukon Gigabit) Wireless RTL8187 b/g - 32bit Works (Native Patch REALTEK) (64bit Work Kext Mod PIEROF81) USB 2.0 - Native all Work USB 3.0 PCIe (LACIE) - Native all Work SUPER SPEED IDE - Natine all Work E-SATA 3GB - Natine all Work Shutdown/Reboot - Work (Stop Work_Kext SleepEnabler x64)	Patches Built-in Realtek Wireless (RTL8187B) PRIVATE Full kext edited by PIEROF81 Tools Link Kext Helper B7
P5B	P965+ICH8	use Retail 10.6.3 , dsdt.aml, NV8400GS (old one), LAN onboard works, Sound alc1988b not work (use external USB). Upgrade 10.6.7 with ComboUpdate and direct update to 10.6.8 from Apple.
P5K Premium/WiFi-AP	P35/ICH9R	Intel Q9400 CPU 2.66 GHz @ 3.66 GHz 8400GS (256MB) works fully with GraphicsEnabler=y. 2x2GB 800 MHz Ram Audio - works with the latest Voodoo (Output and Inputs) Ethernet - Works Wireless b/g - Works (see patches column) USB - All Work IDE - ? ICH9R - Works Install Method: Retail Disk Image boot with myHack then Apple Software Update to 10.6.8 Shutdown/Reboot work 99.9% of the time.	Patches Realtek Wireless (RTL8187B) myHack (chameleon + other stuff) Audio (VoodooHDA) Useful Tools OSX86Tools Kext Helper B7 Guide EFI Studio
P5KPL-AM/EPU	G31 / ICH7	System IMAC-PEO-EDITION: Asus P5KPL-AM/EPU Nvidia GT 220 1024 GDDR2 Intel QuadCore Q9400 Muskin DDR2 800MHz 4GB Install: iBoot with retail SnowOSX_Universal_10.6(432)GM-v3.5 DVD Boot system with iBoot, insert dvd and press f5 When install,click customize and deselect all update with 10.6.8 combo updater (don't reboot) after many kernel panic, i prefer replace AppleACPIPlatform and IOPCIFamily from snow leopard 10.6.7 At this point i try and retry update install but at reboot result is: dsmos.kext kernel panic. remove this kext (if you have) before reboot and after run Multibeast. System Utilities and other customized kexts: AttansicL1eEthernet, Latest VoodooHda, SleepEnabler for 10.6.8 Access Icloud follow this post http://www.insanelymac.com/forum/index.php?showtopic=263794&st=0&p=1725710&#entry1725710 and it work! :))) If you have any kernel panic, try with -x -v npci=0x2000 flag, and if you have problem with graphic with quote GraphicsEnabler=Y, and again if you have a generic problem try DSDT=No (after Multibeast :) ) Ethernet: works Audio: works Video: with Nvidia Driver for 10.6.8 Sleep: works	appleacpiplatform_and_iopcifamily_10.6.7 AttansicL1eEthernet NVIDIA DRIVER 10.6.8 VoodooHda SleepEnabler 10.6.8
P5KPL-AM EPU	G31 / ICH7	System: Asus P5KPL-AM EPU Asus EN8400GS Intel E6700 DualCore 3.2GHz Corsair DDR2 800MHz 4GB Kit Install: iBoot with retail 10.6.0 (on USB HD) Boot system with iBoot update with 10.6.8 combo updater (don't reboot) kexts: AttansicL1eEthernet, VT1705 (works fine with VT1708), SleepEnabler for 10.6.8 Ethernet: works Audio: works Video: works Sleep: works	AttansicL1eEthernet VT1705 SleepEnabler 10.6.8
P5Q SE2	P45	System: ASUS P5Q SE2, NVIDIA Geforce 8800GT 512mb, Intel Core 2 Quad Q8300, 6GB RAM, 500GB WDC Install retail Mac OS X 10.6 with IBoot download OSX Combo update Install Mac OSX combo update 10.6.8 Ethernet: Works Audio: Works with VoodooHDA Video: Works	VoodooHDA
P5Q SE2	P45	System: ASUS P5Q SE2, NVIDIA Geforce 8500GT 512mb, Intel Core 2 Duo E8500 3.16Ghz, 4GB Samsung RAM, 500GB WDC Install retail Mac OS X 10.6.3 download OSX Combo update Install Mac OSX combo update 10.6.8 Ethernet: Works Audio: Integrated audio works with VoodooHDA External M-Audio Fast Track USB works without any issues Video: Works	VoodooHDA External M-Audio Fast Track USB works without any issues
[2]	G45/ICH10R	System: ASUS P5-VM, AMD Sapphire 5670 1GB, Intel Core 2 Quad Q6600, 8GB RAM, 320GB Seagate w/2 more SATA drives iAtkos s3 10.6.3 disk Boot in safe mode w/verbose just to see what's going on (-x -v) download OSX Combo update Install Mac OSX combo update 10.6.8 to enable 5670 without injectors/hacks/etc. Ethernet: patched from DVD with 8168 kext. Audio: Requires AppleHDA_ALC1200_HDEF.zip patch [from Forum].	Ethernet RTL8186.kext from iAtkosDVD / AppleHDA_ALC1200_HDEF.zip patch [from Forum]
M2N-SLI	nForce 560 SLI	AMD Athlon 64 X2 Dual-Core Processor 5200+ 2.70 GHz 2xIDE DRIVE , 2x SATA DRIVE , 2x IDE DVD-RW/RAW 2GB RAM nVidia GeForce 8400 GS Audio: C-Media C6501, Voodoo Audio LAN: nForce4 SLI CK8-04, nVidia/Force Patchs SATA & IDE: Yes Works, SATA Driver from Application Optical Drive: LG and HITACHI, Works Perfectly. Only SHUTDOWN Works Any other details	AMD PATCH and Charmeleon (But dont shure because i dont remember the name) All Works, except Wi-Fi.
P5N-E SLI	nForce 650i SLI	Intel Core 2 Quad Q6600 IDE DRIVE & IDE DVD-RW 6GB RAM Nvidia GeForce 9400 GT Follow this guide			?
P6T Deluxe V2	X58/ICH10R	System: ASUS P6T Deluxe V2, Intel Core i7-920, 2.66 GHz, 6gb Kingston HyperX SATA - Works with AHCI set in BIOS USB - Works Ethernet: Works Audio works after you run Audio patcher for SL 10.6.8 & Lion GM (follow guide) Video Palit Gtx 285 (1024MB) DDR3 - Works	Guide
P75KPL-VM	Intel G31/ICH7	System: Intel E2180, 4 GB RAM, 500GB Seagate HD SATA, GeForce 8400GS 256MB Installation: iBoot (3.1.0) + Multibeast (3.7.3). Installed from the original Snow Leopard 10.6.3 DVD and then upgraded (via ComboUpdate) to 10.6.7. then update 10.6.8 by Software Update Multibeast: used UserDSDT build by DSDT Auto-Patcher. Monitor : connected via DVI. Video: Multibeast (NVEnable) Audio: AppleAzaliaAudio.kext Ethernet: AtherosL1Ethernet.kext USB: OOB SATA/IDE: OOB	Patches applied via Multibeast: NVEnable
P7H55D-M EVO	Intel H55	System: Intel Core i5-650, 4 GB RAM, 2 x 500GB Seagate HD SATA, GeForce GT 9500 1 GB Installation: iBoot (3.1.0) + Multibeast (3.7.3). Installed from the original Snow Leopard 10.6.0 DVD(Retail 10.6.3 also works) and then upgraded (via ComboUpdate) to 10.6.8. : applied the patches. No custom DSDT used. Additionally you may install Nvidia Retail Drivers. Monitor connected via DVI. Video: Out of the box Audio: VoodooHDA 0.2.72 (microphone not working) Ethernet: Lnx2Mac's RealtekRTL81xx USB: Out of the box SATA/IDE: Out of the box	Patches applied via Multibeast: VoodooHDA 0.2.72 Lnx2Mac's RealtekRTL81xx
P7P55-LX	P55	Intel Core i5-750 2.66 Ghz SATA HD 1 TB (switched on AHCI configuration from IDE) and SATA SONY DVD-RW DL 2x2GB (4GB) RAM Corsair Dominator XMS3 1600 Mhz Sapphire Ati Radeon HD 5770 1 GB Vapor-x Install Mac with iAtkos S3 v2 with this configuration: Important: If the iAtkos installer crashes on start, start the pc using the iAtkos DVD and press F8, write this -v cpus=1 busratio=20, it will work. 1) Chameleon RC4 bootloader 2) Boot with 32-bit mode 3) DON'T USE Graphic Enabler for now. 4) In Bootloader options --> USB check all. 5) In the same menu check Ethernet too and, if you want, check Legacy Logo (you will have the original Apple Logo when booting) 6) In Patches menu don't touch anything. Don't use modified kernels or USB fixes. 7) In Drivers menu check only Main Hardware --> Sound --> Both drivers (Vodoo and Apple). If you use PS/2 keyboard or mouse, check PS/2 too. 8) Don't touch VGA for now. 9) In network choose Wired (if you're connecting with Ethernet) and select Realtek --> RTL8168. 10) In Language Translations choose your language. 11) Install all. 12) Reboot and log on the OS. If MacOS come up with an error and you need to restart the computer, still use -v cpus=1 busratio=20 for every boot. 13) To install VGA drivers, download Kext Helper v0.7 (this is the last version for now) and download ATI 5000 Series drivers 32-bit from www.kext.com. Use Kext Helper to install all the content from the ATI 5000 Series driver directory. 14) Install Apple Combo Update to get 1.6.8 version. 15) Enjoy your system. With this configuration all works: VGA, USB and internet connection.			?
P7P55D-E LX	P55	Core i3 530 and ATI HD4670 graphics full installation proccess is here [3]
P7P55D-E PRO	P55	I used Retail 10.6.0 with iBoot with PCIRootUID=1 at start. It is a Core i7 870, and a friend gave me an Apple GT 120 video card. He was going to bin it! After updating with 10.6.8 combo update every thing works with out any additional kexts. So I did not install Multibeast - easybeast keeping as 'vanilla' as possible. So I use the iBoot cd to boot; the small price to pay. I Used Retail 10.6.8 with iBoot PCIRootUID=1 at start. I have a Radeon HIS 5830 HD. Before I got the video drivers installed for it I was not able to get it working without PCIRootUID=1. Also Sound does not work from motherboard.
P8H67-M Evo	H67	Core i5-2400 and ATI HD5750 graphics Used Multibeast 3.8 with lnx2mac Realtek 81xx drivers, USB fix, PCI fix and com.apple.boot.plist's PCIRootUID=1 key HD 5750 graphics don't work with 10.6.8 drivers, reinstalled 10.6.7 ATI kexts back.
P8H67-M LE	H67	Core i7-2600 Sandy Bridge and ATI Radeon HD6870 graphics Installed Retail 10.6.3 first, then tonymacx86' Update Helper, then Combo Update (used Multibeast before reboot) Used Multibeast 3.8 with lnx2mac Realtek 81xx drivers, Renesas USB 3.0 fix, PCI fix and com.apple.boot.plist's GraphicsEnabler=no key HD 6870 graphics don't work with 10.6.8 drivers, reinstalled 10.6.7 ATI kexts back.
P8H67-M Pro	H67	Core i5-2400, EVGA GT210 512mb, 4GB DDR3, SEAGATE 320GB Using iBoot and 10.6.3 Retail DVD, install 10.6.3. No other patch required. Apply UpdateHelper by tonymac, Reboot, Install Combo Update 10.6.8, DO NOT REBOOT Apply Multibeast 3.8, select easybeast, lnx2mac, system utilites, ALC8xxHDA + AppleHDA Rollback + EnableHDA Sound, LAN, Graphics (fully), USB, restart/shutdown, timemachine everything is working (Sleep not tested)
P8P67 Pro (REV 3.1)	P67	Core i5-2300 Sandy Bridge, XFX Radeon HD 5450 1GB, 8GB DDR3 (4x 2GB), SEAGATE 1TB 7200 RPM 6.0Gb/s Followed the install guide on InsanelyMac found Here Sound, LAN, Graphics (fully), USB, restart/shutdown.	^Andy^_*'s Boot CD and Post Install Package. Found Here
P8P67 DELUXE(REV 3)	P67	Core i5-2400 3.10 GHz 6MB Cache, Sandy Bridge, Ati X1650 Dev ID 0x71c3, 8GB DDR3 (4x 2GB), 2x SEAGATE 500 GB Sata Followed the install guide on InsanelyMac found Here, Sound, LAN, USB, Sata, restart/shutdown. Graphics (Full resolution, NO DUAL SCREEN) Installed JUST EVOEnabler.kext taken from here, Edited ATI1600Controller.kext/Contents/Info.plist with VGA DeviceID (0x71C3), Edited EVOEnabler.kext/Contents/Info.plist with VGA DeviceID (0x71C3), Graphics (QE/CI Enabled) Followed "QE/CI hexadecimal edit" section from this old guide (otherwise the following step will lead to kernel panic due to hard-coded deviceID references), Edited ATIRadeonX1000.kext/Contents/Info.plist with VGA DeviceID (0x71C3).	regae' s Boot CD, Post Install Package and 10.6.8 Update Helper. Found Here EVOEnabler.kext from this dmg		?
P8Z68-VPro	Z68	OSX Universal Installer 10.6.2 v3.6 ( you might use other Hackintosh/Retail image ) CPU i7 2600K MEMORY G.Skill 2x2G 1600Mhz GPU Gigabyte GTS250 VGAxDVIxHDMI Asus ML 24 (HD) - works with VGA connector only (no native HD so far with my card) DVD WR Samsung Installation Start with Simple installation without iBoot (used the DVD own bootloader). /// Im a different user and I think best method is : To use iBoot. If you use iboot, when booted on CD, under iboot screen, after changing CD with DVD Install, press tab to inter simple mode (i did it to find the = and correct issue with keyboard) and use this command : PCIRootUID=1 -x to be able to reach install screen. I used the 10.6.0 DVD. Dont use Andyboot, its friendly user but doesnt work when installing10.6.8. After install : Use again : PCIRottUIS=1 -x but choose the place you installed Snow /// Do Not use the DSTD instructions when installer loads. just run the default installation. After installation, used the iBoot (iBoot Legacy for sandy bridge) to load into the OSX. Run ####### and pick: #########. intel 1000 network. To Enable Sound: AppleHDA Rollback, ALC8xxHDA, Under Non-DSTD HDAEnabler - pick ALC892 [pre-requisite for sandy bridge & 10.6.8 combo update] Run UpdateHelper. Reboot When OS loads it might not be responsive in the first few minutes, just wait ~2minutes. Install Snow 10.6.8 Combo Update [optional, if you have issues with bootloader] Reboot	RealtekR1000SL.kext Audio Multibeast: rollback, enabler and legacy(after 10.6.8)
Sabertooth X58	X58 / ICH10R	System: Asus Sabertooth X58 MSI R5770 Hawk Intel Core i7-960 Bloomfield 3.2GHz G.SKILL Sniper Low Voltage Series 8GB (2 x 4GB) Install: iBoot with retail 10.6.3 (Retail CD) with your HD plugged into the FIRST SATA3 port (the black ones, the upper one on the opposite side of the grey SATA6 ports) Boot system with iBoot update with 10.6.8 combo updater (don't reboot) kexts: USB 3.0-NEC/Renesas Ethernet: works Audio: works Video: works Sleep: works
Sabertooth X58	X58 / ICH10R	System: Asus Sabertooth X58 XFX HD5770 Intel Core i7-950 3.08 GHz Patriot 16GB (4 x 4GB) Case Yeong Yang Cube; http://www.yycase.com/yy-0221.htm Install: From other Hackintosh system Boot system with iBoot update with 10.6.8 combo updater (don't reboot) kexts: USB 3.0-NEC SSDT tables using Hackintosh Hardware Analyzer from Ubuntu; http://www.projectosx.com/forum/index.php?showtopic=1341 Ethernet: works Audio: Work all channels, No rollback; http://www.insanelymac.com/forum/index.php?showtopic=263930 Video: DVI-HDMI Sleep: Not work SATA 6GHz Works (Marvell 88SE9123) All system working without error Dual boot with Win7 64
E35M1-M Pro	AMD FCH A50	System: Asus E35M1-M Gigabyte Nvidia 240 GT AMD Fusion APU E-350 (Dual Core overclocked to 1.76 GZ) Kingston DDR3 1333 4GB Kit (overclocked at 1433) Install: Installed retail 10.6.0 on another mac (show invisible files then installed from Installation/Packages/OSInstall.mpkg) updated to 10.6.8 combo updater VoodooHDA 0.2.61 (audio for HDMI works) / Lnx2Mac's eraltek network driver Legacy kernel from nawcom (patched drive with Maxxus AMD patcher) in com.apple.Boot.plist arch=i386 -force64 busratio=20 Ethernet: works Audio: works (onbaord disabled) Video: works (enabler=y + GT215.rom in boot.plist) Sleep: not tested	Legacy kernel
P5E3 Premium/Wifi-AP	Intel X48 - ICH9R SATA	Intel Q9550 CPU 2.82 GHz @ 3.4 GHz Corsair Xms3 1600MHz (4x2Gb) ATI HD4870 TOXIC (512MB) - Works Audio - Works (bad) Ethernet - Works WiFi - Works likely AirportExtreme USB - Works (all) Shutdown/Reboot - Works Sleep - Not work Install Method: iBoot+Multibeast Combo update 10.6.8 Before Install: Enter in Bios Disable JMicronATA Set Sata to AHCI Note: Choose iBoot Legacy cd iBoot with -x First boot OS X with -x flag Install Update (DON'T REBOOT!) Delete appletymcedriver.kext from Extensions folder	In Multibeast: EasyBeast System Utilities Drivers & ... - Kext & ... - Audio - Realtek ALC8xx - AppleHDA RollBack Miscellaneous - IOUSBFamily Rollback Realtek Gigabit Ethernet Patches Kext and DSDT updated Repository code DSDT
Striker II NSE	Nforce790i SLI	bios revision 0901 you can save your bios setting under tools in your bios :) 32 bit Q6600 CPU @ 2.4 Ghz overclocked in bios to q6800 6gm ram 2 1gig 2 2gig all by ocz After installing IPC 10.5.6 or Hazard 10.6.6i follow youtube video [4] after snow leopard 10432 which is 10.6.0 is installed use the combo update by apple 10.6.8v1.1 Do not use software update causes issues Sound=Voodoohda.kext works no digital audio yet..airfoil is what I used to get audio to stream to airport express for the time being. Also if using vlc delay audio to -2050. Video=Nvidia Gtx280 works hdmi full 1080p no audio via hdmi yet Ethernet=Both On board nic's work. Used Netkas support files installed ionetworkingfamily.kext in S/L/E then showed the packages contents and deleted nvenet.kext in plugins then put NforceLan.0.64.5.kext (This improved the stability of the machine immensely and torrent downloads now seem stable!) Ide works OOB Sata works Usb works Esata rocketraid 2302 Enable plug and play OS in bios then it works also use cpus=2 as a boot flag only running as dual core but still useable if you want e-sata support. AppleNforceATA.slash.kext needs to be updated for raid support see this link http://code.google.com/p/darwin-ata/issues/detail?id=2 Kexts used in S/L/E all in verdants v2.3 support files Install them there or you will have issues Ionetworkingfamily.kext modified by me :) AppleNforceAta.slash.kext or AppleNForceATA.imk64bit.kext since I have over 4gb of ram JmicronATA.kext (When I replaced this existing kext it helped my raid become more stable) Files in Extra Com.apple.boot.plist DSDT.aml upper case for chameleon to read it needs to be modified so you do not lose your bios settings. (http://netkas.org/?p=114) I used dsdtse to extract, DO NOT USE THE INSTALL DSDT OPTION YOU WILL WRECK YOUR OS! SMBIOS_MacPro31.text Files in E/E Openhaltrestart.kext Disabler.kext Fakesmc.kext Platformuuid.kext My com.apple.boot.plist <key>Kernel</key> <string>mach_kernel</string> <key>Timeout</key> <string>5</string> <key>Kernel Flags</key> <string>arch=i386 pmVersion=0</string> <key>EthernetBuiltIn</key> <string>y</string> <key>GraphicsEnabler</key> <string>y</string> <key>PciRoot</key> <string>1</string>	Vanila
P7H55-M	Intel H55	System Configuration: CPU: Intel Core i5 760 @ 4.0GHz Video: Palit Geforce GTX 460 Sonic 1GB LAN: Onboard Sound: Onboard Storage: H55 SATA Install Method:	(Used cpus=1 PCIRootUID=1) Retail Mac OS X 10.6 Snow Leopard 10.6.8 Combo Update  : Lnx2Mac's RealtekRTL81xx Ethernet Chimera v1.5.4 r1394 FakeSMC ALC8xxHDA Non-DSDT HDAEnabler Official NVIDIA Drivers
P5Q SE	Intel P45 / Intel ICH10	System Configuration: Install Method: iBoot+Multibeast (10.6.3 -> 10.6.8) Motherboard: Asus P5Q SE BIOS: Asus 1003 CPU: Intel E8200 Core2Duo Video: XFX ATI Radeon HD4890 1024MB DDR3, DVI works fully after Combo Update and ATI 48xx RAM: Corsair DDR2 2GB (2x1Gb) HD: Samsung 360 Gb Components Status: Audio - onboard - use Voodoo generic Ethernet - Attansic L1E kext from kexts.com + EFI Studio 1.1 USB 2.0 - Native Support IDE - No IDE support CPU - Speedstep -Native support Firewire: Native Support Video - Graphics Enabler= yes / ATI 48xx - full resolution 1920 x 1200 / DVI-->VGA single screen Post Install: Combo Update Mac OS X 10.6.8 v1.1 [5] After update run Multibeast	Multibeast Attansic L1E Voodoo generic

Biostar

Hardware Name	Chipset	Notes	Patches Used	32/64bit working with patches
TF7050-M2	GF7050 PV / NF630 (MCP68PV)	AMD X2 4200+ 2 x 1Gb DDR2 RAM @ 800Mhz VGA : Geforce 9400GT, 1G, 128bit (Digital Alliance) [10de:0641] DVD-RW on SATA LAN : RTL8168B/8111 [10ec:8168] Audio: 7.1-CH HD ALC888 CODEC [10de:055c] non ps2 keyboard and mouse Install Using: Snow Leopard 10.6.3 Intel only by iAtkos S3 10d573 Upgrade with Combo update 10.6.5 [6] Upgrade with Combo update 10.6.7 [7] After Update suspend restart, and you must change your old SleepEnabler.kext on /E/E or /S/L/E, with newer version [8] Upgrade Kernel with legacy_kernel 10.7 [9] with kernel flag arch=i386 -force64 at com.apple.Boot.plist, thanks for nawcom. You must patcher libSystem.B.dylib on /usr/lib/ and QuickTimeComponents on /System/Library/QuickTime/QuickTimeComponents.component/Contents/MacOS/ [10], If you not patch, all 32bit .app can't run, thanks for AnV. Force upgrade to 10.6.8 [11] with pacifist, cause can't manual update. After Update suspend restart, and you must change your old ACPIMonitor.kext, FakeSMC.kext, EvilIOPCIFamily.kext, EvilAppleACPIPlatform.kext, NVClockX.kext, SleepEnabler.kext on /E/E from [12] & Upgrade Kernel with legacy_kernel 10.8 [13], thanks for nawcom, Anv, mojodojo, netkas. Shutdown/Restart: Fully working Sleep still problem BIOS setting: SATA AHCI enabled HPET enable Disable bit enable	/E/E folder : ACPIMonitor, Disabler, FakeSMC, EvilIOPCIFamily, EvilAppleACPIPlatform, NVClockX, FakeSMC, NullCPUPowerManagement, , ElliottForceLegacyRTC, SleepEnabler.
TA-790GXB A2+	AMD790GX/SB750	AMD Athlon II x2 250 3GHz 4x1 GB DDR2 PC 6400 RAM PIONEER SATA DVD-RW LAN Realtek 8111 Audio Realtek ALC662 HIS ATI Radeon HD 5750, 1gb GDDR5 PS/2 Keyboard & Mouse Install using: Snow Leopard 10.6.3 from iAtkos s3 v2 (during customize install, use chameleon 2.0 RC5 and qoopz 10.3 kernel) No luck so far when tried to install the bootcd + retail way, panics either during launch or in the middle of installation Combo Update to 10.6.8 (don't reboot yet by force quitting the installer) then install legacy kernel 10.8 by nawcom Add 0x68BE1002 to Info.plist from ATI5000Controller.kext in S/L/E for QE/CI, repair cache and permission and rollback USB from multibeast and then Reboot Audio still using voodoo driver so it still not working properly Ethernet working by selecting Realtek wired kexts during iAtkos install Sleep not working both 32-bit and 64-bit are working BIOS Setting SATA AHCI enabled Disable cool n quiet Disable floppy (this mobo have floppy enabled by default which led to KP during install)	busratio=15 some 64-bit application often crashes due to the AMD K10 lacks of SSSE3 and SSE4.1 instruction (present on core2duo and higher) GraphicsEnabler = Yes

EVGA

Hardware Name	Chipset	Notes	Patches Used	32/64bit working with patches
X58 SLI LE	X58	Iatkos 10.6.3, You need to install after first boot 10.6.7 update to avoid restar over and over again, NV9800GT (dual DVI), LAN onboard works, Sound alc889 work. Upgrade 10.6.7 with ComboUpdate and direct update to 10.6.8 from Apple. Iatkos options default just add video, ahci sata and jimicron, evospeedstep,quick boot,legacy logo, leguage as well and uncheck sound. dont need dsdl usb work out of the box. sleep doesn´t work	RealtekR1000SL.kext,audio Multibeast rollback,enabler and legacy(after 10.6.8)
X58 FTW3	X58	Iatkos 10.6.3, You need to install after first boot 10.6.7 update to avoid restar over and over again, NV250GTS (dual DVI), LAN onboard works, Sound alc892 work. Upgrade 10.6.7 with ComboUpdate and direct update to 10.6.8 from Apple. Iatkos options default, efi string, ahci sata and jimicron, evospeedstep,quick boot,legacy logo, leguage as well and uncheck sound. dont need dsdl usb work out of the box. sleep doesn´t work. CPU Xeon E5620 2.4ghz MEMORY ADATA 12 ghz 1333mhz non ECC in 3 slots GPU GTS250 dual dvi (works as first class) DVD WR Lg Generic Sata HDD 3 X 1TB seagate sata II nedd help with sleep????	RealtekR1000SL.kext,audio Multibeast: usb3 nec, rollback,enabler and legacy(after 10.6.8.

Foxconn

Hardware Name	Chipset	Notes	Patches Used	32/64bit working with patches
BlackOPS	Intel X48 Chipset	Intel Core 2 Quad Q8300 2.3GHz, 6GB DDR3 Zotac GTX260 896 DDR3 Intel X48 Chipset ...Install... Retail DVD from 8GB partition of primary HDD ...Post-Install... LAN: Broadcom 578x SATA Audio Optical Drive: Samsung Sata DVD Burner Do shutdown, reboot and sleep	Video: Works with NVEnabler + 64-Bit GraphicsEnabler=No Audio: Works with ALC8xxHDA + AppleHDA Rollback LAN: Buy Ethernet Card SATA: Works with included ACPI patch
P35A	Intel P35/ICH9	Intel Core 2 Duo E4500 2.2GHz, 4GB DDR2 NVIDIA GTX275 896MB DDR3 Both processors working with proper fix applied in DSDT.aml file (which is already done in my DSDT) or 6B3F1P40 modified BIOS by OriginalMACNUT, otherwise Cpus=1 fix must be enabled. ... Install ... 10.6.3 Retail DVD Install method - Installed Retail DVD from 8GB thumb drive ... Post-Install ... Bootloader - Chameleon-2.0-RC5-r1091 Audio - patched AppleHDA or VoodooHDA Video - using DSDT patch, but also all other methods are working Ethernet - Works OoB SMC - FakeSMC rev.474 10.6.8. updated w/o single problem Sleep/Wakeup works properly with my DSDT Shutdown/restart working properly	Foxconn P35A tools pack - all-in-one post-installation tool pack designed specifically for this motherboard
G41MXE-V	Intel G41/ICH7	Install method: iATKOS S3 v2 + software update. Updated BIOS first, disabled legacy USB support Foxconn G41MXE-V LGA 775 Intel G41 Micro ATX Intel Motherboard Intel Celeron E3400 Wolfdale 2.6GHz 1MB L2 Cache 4GB ram EVGA GeForce 8600 GTS 512MB All defaults in configuration except I selected realtek ethernet drivers, nvenabler Sleep not working OOB, it seems. Don't care to try to fix it Shutdown/restart working Audio working Graphics acceleration confirmed (dashboard add item - waves) Good picture over DVI on my 1080p monitor Running synergy client so I can use my keyboard/mouse from my main windows box. Highly recommended - just move mouse across to mac screen Edit: Updated using software update to 10.6.8 with no issues.	NVEnabler, whatever realtek kext is in iAtkos S3
45CMX	Intel 945G ICH7	Install method: Leohazard 10.6.2 + combo update to 10.6.6 + combo update to 10.6.8 (delete sleep enabler) Intel Core 2 Duo E7200 Wolfdale 2.5GHz 3MB L2 Cache 4GB DDR2 800 (2x2GB) ram Ati Radeon HD 5670 1GB DDR5 / Onboard GMA950 working with Leohazard drivers and full QE/CL with [14] All defaults in configuration except + ATY_init enabler (to have UI at first boot) Shutdown/restart working Audio working with Legacy HDA FULL QE/CL Dual display VGA+DVI, HDMI not tested but shows up in System Profiler under Graphics USB/PS2 working both OOB	ATY_Init when installing, removed after, installed latest Chimera or Chameleon with the latest Kabyl bootloader and used ati rom from techpowerup (see ATI section for 5670)
G31MXP	Intel G31/ICH7	Install method: SnowOSX Universal 3.6 10.6.2 + combo update to 10.6.8. After installed Bootloader_PCEFI10 Intel Core 2 Quad [email protected] 4GB DDR2 1066 (2x2GB) ram nVidia GeForce GT 220 1024MB VRam working with EFI (com.apple.Boot.plist) and full QE/CL over DVI: 1680x1050, 60Hz Onboard GMA X3100 not tested Default BIOS CMOS Reset working with DSDT Ethernet: Realtek RTL8111/8168 PCI Express Gigabit (Onboard) 10/100/1000 working with SnowR1000 Sound Card: ALC662 working with voodooHDA Shutdown/restart working with EvOreboot Sleep not working USB working OOB (USB mouse/keyboard)	ALC662 working with voodooHDA 2.0.72
H-I41-uATX (Eton)	Intel G41 Express	Install method: iboot cd + Snow Leopard retail CD (on USB) Intel Pentium E6500 @ 2.93GHz, Wolfdale 45nm Technology 4.00 Go Dual-Channel DDR3 @ 533MHz (2x2Go) NVIDIA GeForce G210 BIOS set to CD boot priority Sound: worked fine after installing VoodooHDA 0.2.56kext Video: NVIDIA GeForce G210 working without kext Shutdown/restart Sleep not working All USB ports directly working Ethernet: Realtek RTL8103EL 10-Base-T, works perfectly after downloading the kext from Realtek website: RTGMac_v2.0.6 Wifi pcie card (ASUS PCE-N10 Wireless-N150 PCI Express Adapter) not compatible and not working, no kext available	Sound: installed VoodooHDA 0.2.56 Ethernet: downloaded and installed from Realtek website: RTGMac_v2.0.6, works perfectly

Gigabyte

Hardware Name	Chipset	Notes	Patches Used	32/64bit working with patches
GA-880GMA-UD2H v 2.1	AM3	Kernel: Nawcom Legacy Kernel 10.8.0 Kernel flags: arch=i386 -force64 maxmem=4096 AMD Phenom II X6 1090T 6x 3.2GHz Memory: 4GBx2 GSkill DDr3 1333MHz Graphic: Sapphire AMD Radeon 6850 Audio: works only as an output (azalia audio kext) LAN: Onboard Realtek works (realtek RTL81xx kext) SATA & IDE: works USB3: works ( usb 3.0 patch from install DVD) Optical Drive: LG works Shutdown works, Reboot works, Sleep working (no USB after wake-up)	Installing using Hazard 10.6.6i: GraphicsEnabler=no, partition type MBR Combo update to 10.6.8 and using Chimera 1.9.0 as bootloader gives full QE/CI
GA-MA78LMT-US2H	AM3	Graphic only works, if you update on 10.6.8! Im used 10.6.3 Retail, Nawcom 0.31 Modded CD as Bootloader to install OSX AMD Phenom II X4 840 4x 3.2GHz Memory: 4GB Kingston Value DDR3 (on OSX identify only DDR2!!!!) Graphic: GIGABYTE Radeon HD 5770 Super Overclock Audio: works perfect, but very quite LAN: Onboard Realtek works SATA & IDE: work Optical Drive: LG work Shutdown works, Reboot not & Sleep mode did´nt tested	Using Chameleon Bootloader 2.0 RC5, on multibeast computer doesnt start! For German help send me an Email to [email protected] & german tutorial: http://www.root86.org/entry.php/16-AMD-Hackintosh-Phenom-Snow-Leopard-10-6-8-Retail-Anleitung
GA-Z68X-UD3P-B3	Z68	BIOS : F6 Intel Core i7 2600k (up 4.6GHz) Memory : 16GB of Ram (smasung 4gb x 4slots) (DDR3) Video : PCI-E 1024МБ Sapphire "Radeon HD 6870" Audio : Realtek ALC889 Network RTL8111E Graphic Full working with QE/CI Hard Disk : hitachi&WD 500gb	Installed 10.6 Retail to install the combo update 10.6.8 cloning system on usb drive and install the update on it. when installed on a live system, it fell into the kernel to panic even if you use nulcpupower kext Use nulcpupower kext DSDT created by DSDT autopacher and it's so amazing :) after it delete nulcpupower kext. Audio - VoodooHDA.kext.0.2.62-10.6 Video - work from box with 10.6.8, graphics enabler = no, PciRootUID=1 (I do not know whether or not but I have worked so, and dual monitor too) SATA - AHCI in BIOS (Full working Sata2&Sata3) Ethernet - work with native realtek driver from "http://www.realtek.com/" & DSDT Sleep : works, but usb is not working properly, turn off all attached devices and connects again, which is very bad for the HDD =(((((
GA-Z68XP-UD3P	Z68	Bios: U1e Intel Core i7 2600 RAM: 2x2GB DDR3 1600MHz VGA: Albatron Nvidia 8800 GTS 640MB Audio: Onboard LAN: Onboard	Installed 10.6 Retail through OSX86ModCd (dual boot on MBR disk with Win7 Already on), Combo update to 10.6.8 (tonymacx86 UpdateHelper used for Sandy Brigde) Audio&Network: tonymacx86 Multibeast(EasyBeast, no DSDT for my bios *on edit date*) (installed Realtek Driver, and ALC8xxHDA,AppleHDA Rollback,ALC889 VGA work out of the box Sleep not tested	?
GA-G41M-Combo	ICH7	BIOS updated : September, 06 2010 Intel Core 2 Duo 2.7 Ghz Memory : 2GB of Ram (DDR3) VGA : nVidia Geforce 8400 GS 512 MB Audio : Full working Network Full working Graphic Full working with QE/CI Monitor : Hp w1707 with connect by DVI Cable Hard Disk : Seagate 1TB	Installed 10.6 Retail by EmpriseEFI CD + Combo update to 10.6.8 Installed fakesms.kext, and installed Chameleon RC5 R699, you can choice some different files if you need ) Bootloader - Chameleon RC5 or Chimera 1.1 (Tested on May 6, 2011) DSDT created by DSDT autopacher and it's so amazing :) Audio - Voodoo HDA 0.2.1 Modded to link from Speaker to PCM with Volume Control worked perfectly. Video - nVidia Geforce 8400 GS 512 MB (just only add GraphicsEnabler=y to com.apple.Boot file or you can using nVEnabler.kext) SATA - AHCI in BIOS (Set up default on BIOS) Note : You must saving ACPI + PCI 10.6.7 for 10.6.8 from 10.6.7 install in here to boot without error PCI Config, just on 10.6.8 Ethernet - AtherosL1Ethernet.kext (the below link it's lastest version to fix any random kernel Panic). Sleep & Wakeup : Works no need to SleepEnable.kext ! Here all my file with GA-G41M-Combo: [15] (Found on 3 days to take full files)
GA-EP43-DS3 F9 bios	Intel P43	CPU Intel E6600 @ 2,40 GHz Install with original DVD + iBoot + update to 10.6.7 from Apple + update 10.6.8 : flawless
GA-EP43-DS3L	Intel P43	Geforce 8400GS Sound: ALC888 Ethernet: working Install BIOS cartri, Combo Update to 10.6.8 from 10.6.7 need 3 new patched kexts for sound, from www.kext.com
EP45-UD3LR	Intel P45/ICH10R	For Install use: Kakewalk[16] Mic (green Line) works fine. Sleep and Wake up works perfect. Shutdown/Restard works fine. LAN (DHCP) works fine. If you dont want use Cartri BIOS, check following DSDT: [17]	Zipped Extra Folder: [18] FakeSMC.kext AppleHDA.kext IOAHCIBlockStorageInjector.kext No DSDT File needed -> Cartri 0.8 BIOS [19]
GA-EP45-DS3 (rev. 1.0)	Intel P45/ICH10	BIOS Settings - F10e (this has quickboot mode)- [20] Advanced BIOS Features HDD S.M.A.R.T. Capability -Enabled CPU Multi-Threading - Enabled CPU EIST Function Integrated Peripherals Legacy USB storage detect - Disabled (prevents trying to boot from usb) Initially installed with: Kakewalk (kakewalklegacy.iso from older CD version) [21] ALC889a Audio All analogue and digital audio working Sleep (All boxes need to be ticked in System Preferences > Energy saver) Shutdown/Restart works (PME Event Wake Up - Disabled)	DSDT.aml (for F10a bios) [22] - Kakewalk default gives about 2/3 of full speed ALC889a installed - Kakewalk install sound doesn't work
G41M-ES2l	Intel G41M + Q8200	Video: GTX260 - NVenable + GT200driver.pkg+CUDA Driver for CUDA suport adobe and more Sound: Voodoo HDA works OK mic in line in Ethernet: working Reboot work / sleep not work Install Original DVD Snow Leopard 10,6,3 + Vodoo HDA + NVENABLE Combo Update to 10,6,8
GA G31M-ES2C	Intel G31/ICH7	Fully working and capable upgrading to Lion Memory: 2GB DDR2 Video: NVidia 7200 GS 256 MB - QE/CI fully working through EFI string injection Sound: ALC889 - with VoodoHDA.kext LAN: RTL8102E - Driver download from Realtek website. To enable builtin Ethernet EFI Injection used. SATA & IDE: SATA Works, IDE CD/DVD fine, but IDE HDD somewhat makes Chameleon stuck. Optical Drive: IDE CD/DVD Drive works fine and able to install without problem Shutdown & Reboot works. Sleep probably need DSDT Patch / SleepEnabler.kext (untested) Install Original DVD Snow Leopard 10.6.3 with iBoot + Update 10.6.8 Combo + VoodoHDA + EFI string Injection for BuiltIn Ethernet & Full QE/CI	(VoodoHDA) LAN Driver download from Realtek website, Use EFI Injection to enable Builtin Full QE/CI used EFI string Injection to recognize GeForce 7200 GS Probably need DSDT patch to enable sleep working properly
G41MT-D3V	Intel G41/ICH7	CPU: Q6600 (2.4GHz) Memory: 8GB correctly detected, speed detected Sleep/Wake: fully working Shutdown/Restart: fully working Ethernet: RTL8111E. Fully working with Realtek official drivers v2.0.6. Don't work with VMWare Bridging, use NAT instead. Sound: didn't bother although it is supposed to work OK with the ALC889 patches. I use USB sound so don't need this. Graphics: Built-in G41 not supported. I use Nvidia GT240 (Chameleon GraphicsEnabler only required) USB: fully working. Gigabyte ON/OFF Charge works in Sleep!	Installation procedure: here Boot loader: Chameleon RC5 (latest) DSDT Auto Patcher to create DSDT: fixes sleep/wake, HPET, USB, etc. /Extra/Extensions: Only requires fakesmc.kext (NullCPUPowerManagement.kext & SleepEnabler.kext not required)
GA-EP45T-USB3P	Intel P45 Express/ICH10R	CPU: Q6600 (OC to 2.79GHz) Memory: 8GB DDR3 (4x2GB PNY 1333MHz) correctly detected, speed detected Sleep/Wake: Worked on 10.6.4 when I used DSDT. No DSDT for this install, have not tried sleepenabler kext. Shutdown/Restart: fully working with EvO shutdown/reboot kext Ethernet: RTL8111D. Fully working with Realtek official drivers Sound: Working OK with the ALC889 patches. (Only tested green jack line out. Select internal speakers in sound prefs) Graphics: Running 2x9600GT with Aquamac EFI string method. QE/CI and res change on all cards. BIOS set to PEG, not PEG2. USB: Fully working. USB 3.0 works with NEC kexts.	Installation procedure: install with 10.6.3 retail DVD and update to 10.6.8. Boot loader: Chameleon RC5 (latest) Options: FakeSMC with temp monitor plugins, nullcpupowermanagement, evoreboot, jmicronATA, jmicroneSATA, all ALC889 options, Realtek 8xxx official driver
GA-P61-USB3-B3	Intel H61	CPU: Intel Core i5-2300 Memory: 4GB Cosair XMS3 DDR3 1333 (PC3 10666) Ethernet: Realtek 8111E. Fully working with Realtek patch Audio: Realtek ALC889. Green line working with Realtek patch. Video: EVGA 8400GS 512MB. Full QE/CI (GraphicsEnabler=Yes) USB: OOB. USB 3.0 not tested. Used USB 3.0 patch and ports work as USB 2.0 Reboot/Shutdown work, Sleep not tested, turned off in System Configuration.	Installation procedure: Installed 10.6.0 on separate machine + Combo Update 10.6.8 Used method to create a boot partition and set its org.chameleon.boot.plist to boot to Snow Leopard drive Moved drive to target machine Edit org.chameleon.boot.plist on Snow Leopard partition to GraphicsEnabler=Yes, may have to use PCIRootUID=1 fix
H61M-D2P-B3 rev. 1.0 (BIOS F5)	Intel 6 Series	Video - eVga 8400GS 1GB DDR3 64-bit - Works with editing NVDANV50Hal.kext and PCIRootUID=1 Sound - AppleHDA Rollback and ALC889 Ethernet - Realtek drivers Reboot / Sleep - Works Install guide used with DSDT: Fresh 10.6.0 -> Mac OS X 10.6.8 Helper -> 10.6.8 Combo Update -> Mac OS X 10.6.8 Helper -> MB -> Reboot -> Edit NVDANV50Hal.kext -> Reboot
P55-USB3 Rev2 BIOS F9	Intel P55	Video: ATI-5770 (Powercolor) Sound: Realtek ALC892 - need AppleDHA Rollback after update from 10.6.7 to 10.6.8 Ethernet: working Reboot / sleep works with spleasesleep
X58A-UD7 R2 BIOS FC	Intel X58	Video: ATI-5770, Needs unplug replug after restart, or wait until screensaver kicks in Sound: Realtek ALC889 - works Ethernet: working Reboot / sleep works
GA-X58A-UD3R Rev 2	Intel X58 + ICH10R	CPU Intel i7 950 @ 3,20 GHz - FE Bios. Also works with FF Bios Video: ATI Sapphire 5850HD Vapor X, work OOB Sound: Realtek ALC889a after the update you have to reinstall AppleHDA (appleHDa rollback) Ethernet: working. I installed the Lnx2Mac Realtek RTL81xx Driver. (Look it up online) So far it works well. Make sure to select the debug install option. Reboot / sleep works update from 10.6.6
GA-G31M-ES2L Rev.2.0	Intel® G31 + ICH7 Chipset	Install Method: 10.6.3 Retail DVD + 16GB USB + myHack 1.1 + Combo Update 10.6.8 BIOS Version: FF Audio: ALC883 LAN: AR8131 Chip SATA: OOB IDE: Not Tested CPU: Intel® Core 2 Duo E7500 O.C. 3Ghz RAM: OCZ 4GB (2GB x 2) DDR2 O.C. 1000Mhz HDD: Hitachi 500GB SATA (HDP725050GLA360) Optical Drive: HP DVD Writer 1260d Works OOB Onboard GPU: GMA3100; Not Working GPU: PNY NVIDIA GeForce 8600 GS 512MB	I'll be writing a guide for my install and posting it soon QE/CI: Works w/Graphics Enabler! Mac App Store: Works w/Ethernet Built-in! LAN: Works w/AtherosLC1Ethernet.kext! Audio: Works w/ Voodoo 2.7.3 Installer Package! Bootloader: Chameleon-2RC5-b699 Other: ALC8XXHDA.kext, AppleHDA_Rollback.pkg, FakeSMC.kext, dsdt.aml
GA-G31M-ES2L (Rev. 1.1)	Intel G31M	CPU E8400 RAM 2 x 2 GB Graphics: Nvidia ASUS GeForce EN210 SILENT DVD drive connected via IDE HDD connected via SATA Installation using iBoot and Multibeast Hardware is fully functional including: QE/CI, Sound, Sleep Network is sometimes not available after boot (after booting Linux it's working again in OS X), can be fixed via kext installation guide and files are to be found here: [23]	custom dsdt.aml EvOreboot.kext AppleHDA.kext legacyALC883.kext RealtekR1000SL.kext
GA-G31M-ES2L (Rev. 2.4)	Intel G31M Express Chipset	CPU: Intel Pentium Dual Core E5800 @ 3.20 GHz RAM: 4 GB (2x2GB) Patriot DDR2 800 MHz Graphics: Gigabyte GeForce GT 220 1 GB DDR3 (Use NVEnabler, 64-bit preferred) Audio: RTL888b (Actual Kext, but you need to find this package 10.6.2-AppleHDAInstaller.pkg for it to work) Ethernet: RTL81xx Wireless: Edimax EW-7811UN USB 2.0 Wireless Adapter: Installer package can be downloaded from vendor website. Plug in before installation starts Bluetooth AZiO BTD211 USB 2.0 Bluetooth Adapter: Plug in before installation starts Webcam: HP Webcam 3100: Plug in before installation starts Reboot, Sleep, 64-Bit Kernel Completely Work Installation Guide: OSX 10.6.3 Retail DVD Download Before Install: OSX 10.6.8 Combo Update + DSDT Auto-Patcher + HDEF Gigabyte DSDT Auto-Patcher + AudioKext Package After install has completed and you reboot with iBoot, run combo update, but before you restart to finish the update run the packages in this order: 10.6.2-AppleHDAInstaller, DSDT Auto-Patcher, then HDEF Gigabyte DSDT Auto-Patcher (it will overwrite original DSDT), (NullCPU.....kext, EvoReboot.kext, Repair Permissions, Repair Caches, NVEnabler.kext, and any SMBIOS or 64-bit plist you prefer). When you are done, you will be booting into Chimera (no need for -v or -x, but do it if you choose) with a complete installation.
GA-G31M-ES2L (Rev. 2.4) w/easybeast	Intel G31M Express Chipset	CPU: Intel Core 2 Duo E3200 @ 2.40 GHz RAM: 2 GB DDR2 800 MHz Graphics: Asus GeForce 8400GS 512MB DDR3 **Complicated** Audio: RTL8883 (use VoodooHDA Mulitbeast) Ethernet: RTL81xx (use AtherosL1cEthernet.kext + EFIStudio) Reboot Completely Work Installation Guide: OSX 10.6.3 Retail DVD + Combo 10.6.8 After Upgrade to 10.6.8, Ethernet is lost, and vido is not QE/CI enabled. See install to right. I got Ethernet to work see install instruct to right.	Asus 8400GS DDR3 Installation Onboard Ethernet Instructions		{{}}
GA-H55M-USB3 F11 bios	Intel H55	CPU Intel Core i3 540 @ 3,06 GHz Video: 9800GT PNY recertified dual DVI, work OOB with graphic enabler=yes Sound: Realtek ALC889a after the update you have to reinstall AppleHDA (rollback, legacy and enabler) Ethernet Reboot / sleep works with sleepenabler 10.6.8 kext. install method, install mac os x 10.6.3 retail dvd (use -v if boot issues), boot with iboot cd, install mac os 10.6.7 update, select all kexts you need and utilities,except audio and sleepenabler (if you cant use usb reboot with usb put in cpu), use everything except fakesmc (dont show cpu temperature)need to use a older one an put it in extra files, now use kextutilities an reboot,now install 10.6.8 update dont reboot and install audio and sleepenabler, reboot and thats all, LegacyIOAHCIBlockStorage.kext to avoid yellow hard disk. and please dont use 240GT dont work at 100% check in nvidia section i posted.	fakesmc.kext (old one) NullCPUPowerManagement.kext*sleepenabler 10.6.8 LegacyIOAHCIBlockStorage.kext nec usb 3 patch and ethernet dsdt F11
GA-H67MA-UD2H-B3 F4 Bios	Intel H67	works like a charm, Graphics working (Sapphire Radeon HD 5850), Sound working, Ethernet working even Sleep Mode working (turn's off all fans, consums only 16W in sleep), USB 3 ports are working with full speed, SATA 3 works with full speed read further instructions will write a better tutorial soon see posts by username Seim for settings
GA-H67A-UD3H-B3 (F6 BIOS revision)	Intel H67	Install Snow Leopard Update to 10.6.8 (update causes KP without UpdateHelper. install LAN and audio kexts If using Intel HD 2000 video (integrated into CPU), screen is black after 10.6.8 update reboot. Shutdown system after update, install 3rd party video card, turn system back on. HD 2000 is incompatible with SL. According to this thread it works on Lion (after removing a kext). Install Lion	ALC889, RealtekRTL81xx
Gigabyte GA M56S-S3	nVidia nForce 560	I installed iAtkos S3 V2 first, so 10.6.3.After that, I installed 10.6.8 update combo from apple site, and before restarting I changed the kernel with the latest from Darwin. Bios:F6G Audio:Works ok with VoodooHDA included in iAtkos distro, even after update. LAN: Realtek 8211BL, works with the driver included in iAtkos distro SATA & IDE:Both work, just select AppleNforceATA at the beggining of the installation. Optical Drive: Asus DVD-RW 1814BL-T, working as it should. Shutdown and restart works ok, haven't tried sleep, because I don't use it. The processor, an AMD Athlon II X2 240 is detected as a Core 2 duo. Also the RAM, 2GB of them is properly detected at 800mhz. nVidia Geforce 9600 GT 512MB, installed with NVEnabler64 kext.Everything is working fine.	I use Chameleon bootloader and Darwin 10.8.0.No problems at all, quite surprised it runs so well on an AMD machine.
GA-P67-UD4-B3	Intel P67	CPU: Intel 2600k Graphics Sapphire Radeon HD 6870 Fully recognized with QE/CI working Sound working Sleep Mode working USB 3 working in full speed Installed by 10.6.0 Retail DVD Updated with 10.6.8 Combo Update Installation & Downloaded GA-P67-UD4-b3 DSDT	Sound: AppleHDA Rollback, ALC8xxHDA Ethernet: Realtek Gigabit Ethernet 2.0.6 FakeSMC Plugins USB 3.0 - NEC/Renesas Guarantee one of most recommended parts for hackintosh build in 2011. Everything just works effortlessly from installation, 64bit, audio, ethernet, graphics with QE/CI & multiple display (OOB), even sleep mode just works from the moment. You can see 'Full Tutorial of Making Hackintosh' for more information.
GA-MA770-S3	AMD SB700	CPU AMD Athlon x2 5000 3.0Ghz Video: nVidia 8600GT Sound: Realtek ALC888 HD Ethernet: Autodetected Install Method: Retail with Nawcom ModUSB Retail 10.6.3 Used -> Upgraded with Combo update to 10.6.8 and installed Nawcom's Legacy Kernel for 10.6.8 before reboot.	Nawcom ModUSB autodetected most everything needed to produce a fully functional system! ElliotRTSC Chosen during installer to prevent CMOS wiping (just to be safe) VoodooTSCAMDSync Installed with Kext Helper after Installation - Keeps cores in Sync for better stability/performance Sleep doesn't work with S1 or S3 selected in BIOS. Sleepenabler.kext is installed. Shutdown/Restart broken - EVOReboot and OpenHaltRestart tried with no success VoodooHDA is crackly unless you open the prefs panel and tune it a bit, turn the input gain down and put checks in Use SSE2 and Enhance Audio - Otherwise Kexts.com has a AppleHDA.kext for ALC888 that sounds perfect without tweaks but you lease everything but output. Volume Control didn't work with keyboard controls properly until I upgraded to 10.6.8 Sleep/Shutdown/Restart issues might be fixable. Haven't dug around a whole lot yet. Overall the system is 8/10. Stable enough for daily use (so far) with only minor problems that aren't deal breakers.
GA P55A-UD3 Rev 2.0 (Bios F11)	P55	System Configuration: CPU-Intel i7 870 2.93Ghz Quad Core Graphics-XFX Dual Fan Radeon HD 6850 (OOB in Lion) Wireless-TP-Link PCI Express Wifi Adapter (TL-WDN4800) (OOB in SL/Lion) 16GB Corsair Vengeance Ram (Fully Recognized SL/Lion) 2x Sony Optiarc DVD/CD RW 2x 6GB WD Caviar black HDD 1TB 2x 3GB Seagate Pipeline HDD 1TB Methods Used: iAtkos 10.6 DVD, iAtkos10.7 DVD 10.6 iAtkos DVD in vmware using usb connector then finished it natively 10.7 iAtkos DVD native install with no boot flags If your having trouble burning the DMG version Google the ISO Version - Burns Perfectly!! Using this method (iAtkos) 10.6.8 DOES NOT have to be installed first to get to Lion!! Thanks iAtkos Team... and all the other super users that contribute to this and many other sites!!	Install: Used Base Package Only!! on iAtkos W/Bootloader Chameleon 2.1 Install then combo update to 10.6.8. DONT RESTART RUN MULTIBEAST after install then restart!!! Multibeast it with User DSDT same method as usb install - Google the DSDT and make sure its the exact match!! (GA P55A-UD3 F11 Rev 2.0.aml) or find it on tonymacx86 Easybeast the rest Drivers for Multibeast: Disk Jmicron36 genericsata Sound ALC888 (Under Apple HDA) use the newer one HDARollback Nothing else!! No Fake Smc plugins needed for hardware monitoring (in Lion) OC away!! Boot with iBoot disk to address any usb keyboard/mouse nonrecognition issues when first starting (Only in 10.6) If you run into the dreaded boot0 error when rebooting, reparation the drive and reinstall 10.6 with base package only and Chameleon RC 5 Boot loader usually fixes the problem

Intel

Hardware Name	Chipset	Notes	Patches Used	32/64bit working with patches
DP35DP		Intel Core2Quad Q9550 4GB DDR2 800 - to install use 4gb ram max GeForce GT220 Zogis 1GB - ok dual display Install with chameleon + Snow Leopard 10.6 Retail DVD. On 1st boot: ComboUpdate 10.6.8	Audio (VoodooHDA.kext)
DP67DE B3	P67	Intel core i3 2100 ok 8gb ddr3 1333 - to install use 4gb ram radeon hd4850 sapphire 512mb - ok dual display network intel 82579v realtek alc892 usb 3.0 nec/renesas fw400 - native chameleon with PCIRootUID=1 -x install Dsdt.aml from DSDT fixer	Use DSDT DSDT.aml alc8xxhda, alchdaRoolBack and alc892 enabler non-dsdt ati hd48xx injector, ati hd48xx patch 10.6.8 usb 3.0 nec/renesas patch hnak´s AppleIntele1000 Ethernet NullCPUPowerManagement.kext	No tested
DG31PR	ICH7	Sleep / SpeedStep / USB with Patched DSDT - Audio VoodooHDA.kext 2.7.2 - Lan AppleRTL8169.kext	Auto-Patcher
DG41RQ	IntelG41/ICH7	Intel E7500 core 2 Duo 2.93GHz, 2GB DDR2 RAM, 500 GB HDD SATA, Intel DG41RQ (perfect board), Nvidia GeForce 210 Install 10.6.3 using iAKTOS s2 v3 Install 10.6.8 combo update, DO NOT RESTART Install chameleon Restart system Enjoy (Not sometime it stuck on boot screen, try with -v and boot a couple of times) I have dual boot windows and SL 10.6.8, windows7 was already installed.	Sound, LAN, Graphics (Fully working 1600x1200) Just multibeast it.
D945GCNL	Intel D945 ICH7	Intel E6600 Core2 Duo - 2GB + 2GB DDR2 - GMA950 - AHCI Mode SATA Install Method: Retail Disk Image install on Hackintosh or Mac - Apple Software Combo Update to 10.6.8 - Chameleon 2.0 RC4 R684 - /Extra/Extensions GMA950 - Works Audio - works Voodoo Ethernet - works 10.4 - 10.6 compatible	DSDT.aml AppleACPIPS2Nub.kext ApplePS2Controller.kext fakesmc.kext IOATAFamily.kext IOUSBFamily.kext NullCPUPowerManagement.kext OpenHaltRestart.kext PlatformUUID.kext RealtekR1000.kext SleepEnabler.kext VoodooHDA.kext
D945GCL	Intel D945 ICH7	Intel E6400 Core2 Duo - 1GB + 1GB DDR2 - GMA950 - ATA Native Install Method: Retail Disk Image install on Hackintosh or Mac - Apple Software Combo Update to 10.6.8 - Chameleon 2.0 RC4 R684 - /Extra/Extensions GMA950 - Works Audio - works Voodoo Ethernet - works 10.4 - 10.6 compatible	DSDT.aml AppleACPIPS2Nub.kext ApplePS2Controller.kext fakesmc.kext IOATAFamily.kext IOUSBFamily.kext IONetworkingFamily.kext NullCPUPowerManagement.kext OpenHaltRestart.kext PlatformUUID.kext SleepEnabler.kext VoodooHDA.kext
Intel DG41TY	Intel G41 Express ICH7	Intel Q6600 Core 2 Quad - 4GB DDR2 - nVidia GeForce GTS 250 Boot with iAtkos s3v2 install DVD Format hard drive with GUID partition table --> PC EFI from installer utilities menu --> Install using iAtkos 10.6.3 s3v2 After first boot, I backed up five extensions: AppleAPIC, IOPCIFamily, IOUSBFamily, IOUSBMassStorage, AppleACPIPlatform from /S /L /E Update with 10.6.8 Combo Update, DO NOT reboot. Install backed up kexts with Kext Utility --> Install Kernel 10.8.0 --> Reboot Possible kernel panic, depending on settings. Ethernet and audio work (Do not install VoodooHDA included in this distro, download and install voodooHDA 2.7.3 after first boot) Intel GMA X4500 works only in VESA modes - no support, no hardware acceleration 32 and 64bit PCI-E graphics highly recommended	"Ethernet built-in" enables the ethernet port voodooHDA 2.7.3 Darwin 10.8.0 kernel-- will prevent the "version mismatch for kernel and CPU" panic after update.

MSI

Hardware Name	Chipset	Notes	Patches Used	32/64bit working with patches
Neo2 FR	P35	System Configuration: CPU-Intel CORE DUO E2140 1.6Ghz DUAL CORE clocked to 2x3.0GHz Graphics XFX ATI Radeon HD 4870 4 GB 900 Mhz DDR2 Corsair 160GB Intel X25 SSD Methods Used: 10.6.0 Retail Disc + iBoot Legacy (fails horribly with iBoot 3.x)	Install: Install 10.6.0, dont reboot, install 10.6.8 Combo Update Use these kexts and DSDT.aml http://www.osx86.net/downloads.php?do=file&id=2670 (the HDEF in this DSDT needs to be fixed for ALC888 but the rest is perfect ) Kexts: lnx2mac (LAN) AHCI_3rdParty_SATA (Marvell Controller) PlatformUUID (fixes iCloud bug and other things) AppleHDA (for Sound) ACPIMonitor (sensors) IntelCPUMonitor (sensors) IntelThermal (sensors)
G31TM-P21	Intel G31 and ICH7	My hardware: MSI G31TM-P21 Motherboard Intel Celeron Dual-core E3200 Processor (Recognized as Core 2 Duo in Snow Leopard) Patriot Extreme Performance 2GB 667 MHz DDR2 Single stick 120GB Seagate IDE Hard drive Samsung SATA DVD-RW Optical drive XFX Radeon HD 5670 1GB Graphics card I don't use the onboard graphics, so I can't comment on that. Installation: I used chameleon with a retail 10.6.3 disk I also used Empire EFI v1.08 to boot into the installer, replacing the parts that involved with Empire EFI in step 2. *For the BIOS settings in step 1 of the guide, change all of the settings listed in the guode that are possible and also disable the serial and parallel ports and disable legacy USB support. This board doesn't allow switching to AHCI mode, but it will still work.	Onboard audio and ethernet needed drivers (You can download them here). Use Kext Helper to install the audio kext.		Not known
MS-7250 (K9N Ultra)	NVIDIA® nForce 570 Ultra MCP Chipset	My hardware: Motherboard: MS-7250 (K9N Ultra) CPU: AMD Athlon™ 64 X2 Dual Core Processor 3800+ 2.00 GHz RAM: 2x 1 GB DDR2 800 MHz Graphic: Nvidia Geforce 7600 GT 256 MB (128 BIT) HDD: Sata II-Samsung 160 GB Drive: Sata II-Sony Optiarc DVD burner Installation: Use this guide to install	All things you need can you find here!		Not known
P55-GD55	Intel P55	My hardware: MSI P55-GD55 Intel Core i3-550 Transcend Jetram 4x2GB DDR3 1333MHz 750GB Seagate Barracuda SATA Hard drive LG GH22LS70 SATA DVD-RW Optical drive MSI GeForce 210 1GB DDR3 Installation: I used chameleon with a retail 10.6.3 disk. After that I updated to 10.6.8 by Combo Update. You need this to install the NVidia drivers. Used DSDT file to get LAN (lnx2mac) and Audio sorted (ALC889). NVidia GeForce 210 card needs GraphicsEnabler=No at boot time until you install the NVidia drivers.	You will need to set NullCPUPowerManagement to avoid Kernel Panic. The temperature kexts that work with iStat Pro
P55-GD65	Intel P55	My hardware: MSI P55-GD65 Intel Core i3-530 Kingston 2x2GB DDR3 1.6GHz 1TB WD-Green SATA Hard drive Optiarc SATA DVD-RW Optical drive Palit GeForce 9600GT 512MB GDDR3 Installation: I used this guide with a retail 10.6.3 disk. After I updated to 10.6.8 by Combo Update. After I used installer from a BootCD, because chameleon of it is old, I updated Chameleon using a Chameleon Wizard.	All needed kexts for work are added to BootCD		Not known
MSI 880G-e43	AMD® 880G+SB710	*I don't use the onboard graphics, so I can't comment on that.* My hardware: MSI 880G-e43 AMD Phenom II x4 B60 O'cd to 3.7Ghz 4Gb of Gskill 1600 DDR3 640GB Western Digital Black 7200RPMS ASUS SATA DVD-RW Optical drive Nvidia GTS 450 1GB GDDR5			Not known
MSI X58 Pro-E	Intel X58	My hardware: Intel® Core™ i7-950 MSI X58 Pro-E Sapphire Radeon HD5850 Logitech keyboard USB Logitech mouse USB Wireless Western Digital WD2001FASS 2 TB Mushkin Copperhead 6GB + Corsair Dominator 6GB Plextor PX-880SA LiteOn iHOS104 Installation: I used part of this guide with a retail 10.6.3 disk. After I updated to 10.6.8 by Combo Update. Audio only works with VoodooHDA.
MSI P67A-C45 (B3)	Intel P67 (B3)	My hardware: Intel® Core™ i5-2500 MSI P67A-C45 (B3) Vaikoo N8800 GT with custom cooler Logitech keyboard USB Logitech mouse USB Seagate Sata 250GB WD Blue 500GB Sata VGEN DDR3 PC10600 8Gb (2X4GB) LG DVD RW Sata Installation: I used Distro Installer Hazard 10.6.6i (do not install any application or driver at all). Delete sleepenabler.kext with terminal (I used hazard intaller again and after installation screen appear, choose terminal and delete sleepenabler.kext) and restart, boot to your harddisk that allready installed with snow leopard. Run combo Update 10.6.7 (Do Not Restart!). Run Combo Update 10.6.8 and Restart. Everything run flawless except sleep mode.

Supermicro

Hardware Name	Chipset	Notes	Patches Used	32/64bit working with patches
H8DAE	AMD 8131 / AMD8111	2 x Dual AMD® Opteron [email protected] 1.79 GHz 8 x 2Gb DDR3 RAM @ 1600Mhz VGA : onboard (yet...) DVD-RW on ATA 2x 40GB on ATA LAN : Broadcom® 5704 Dual Port [BCM5701/5704] Audio: none (Airfoil) ABE bluetooth dongle LSI 3ware Escalade 9550SX-8LP (not yet working) Install Using: Linux, use KVM and usb disk to install retail 10.6.3 or 10.6.6i using nawcoms cd Upgrade to 10.6.8 through software update Most things work oob, probably ATA might not work, use AppleGenericPCATA.kext (?) Shutdown/Restart: Fully working Sleep doesn't work (Who needs this anyways??) BIOS setting: nothing out of the ordinary	Nawcom Kernel	not tested
X8SIL-F	Intel 3420	CPU : Xeon X3440 RAM : 4 x 4Gb DDR3 RAM @ 1333Mhz GPU : Radeon HD 5450 DVD-RW 120GB OCZ SSD 1TB 3Gb/s Ultrastar HDD LAN : 2x Intel® 82574L Gigabit Ethernet Audio : None ---- Install Using Your favorite up to date boot CD. Set kernel flag "PCIRootUID=1" Kexts: Fake SMC BIOS setting during initial install and update: Intel Virtualization Technology -Disabled- Simultaneous Multi-Threading -Disabled- Active Processor Cores -1- Intel TurboMode Technology -Disabled-- Set SATA to AHCI VT-d -Disabled- Return these settings to default after initial install and update;except for VT-d	Vanilla Kernel

Graphics Cards

Please specify if your card is AGP, Integrated, PCI or PCI-E.
Also, place chip and board manufacturer in their respective column.

PCI-E

AMD/ATI

Model	Board-Manufacturer	Notes	QE	Output	Dual display	32/64bit working
HD 4670 1GB	XFX	After installed Combo Update 10.6.8 V1.1 Add GraphicsEnabler=Yes PCIRootUID=1 AtiConfig=Pithecia Then repair permissions with kext utility. Mod MASTRI81		VGA/DVI/HDMI
Radeon HD 5770 Super Overclock	Gigabyte	Need Combo Update v1.1 Chameleon 2.0 RC5 npci=0x2000 GraphicsEnabler=No		1x DVI 1x DVI to VGA adapter
Radeon Pro X1300/X1550 Series 256MB	ATI RV516 chip (Dev id 0x7183)	Natively supported by Azimuth's legacy GraphicsEnabler Chameleon branch v2.1 r1515 or main Chameleon branch from v2.1 r2170. GraphicsEnabler=Yes Use EVOenabler for X1000 Series injector kext, patching plist file with complete card identification and replacing framefuffer string (like "Alopias" or "Wormy") by "Sphyrna" (=dual-link DVI) or "Caretta" (=single-link DVI). pre-10.6.8 SL versions can apparently do without this injector kext. Use ATI13000Controller kext, patching plist file by replacing 0x7187 by 0x7183 Use ATIRadeonX1000 kext, patching plist file by replacing 0x7187 by 0x7183 and binpatching MacOS/ATIRadeonX1000 by replacing both instances of hex strings 81 FA 87 71 by 81 FA 83 71. Full QE/CI under Snow Leopard 10.6.x with 32/64bit kernel modes		1x DVI dual-link + 1 x S-Video (low-profile format)	Not tested
X1800XT	MSI	Native support By PIEROF81... 100% Compatible OS X Tiger 10.4.x, OS X Leopard 10.5.x OS X Snow Leopard 10.6.x '32/64 Bit OS X Lion 10.7.x '32/64 Bit !		2x DVI
HD 4350	HIS	Will work after updating with combo update v.1.1 Use Chimera Boot Loader inside multi boot 4.02 , with kernel parameter <string>arch=i386 npci=0x2000</string> Input IOPCIMATCH on /System/Library/Extensions/ATI4600Controller.kext , ( 0x954F1002 ) rapair permissions, and reboot.		VGA/DVI/HDMI
HD 4650	Sapphire	Works with these kexts [24] replace kexts in /System/Library/Extensions. Also included a boot file, which needs to be replaced in the root folder. Add GraphicsEnabler=Yes in com.apple.boot.plist, then repair permissions with kext utility. Power Color HD 4650 1GB DDR3 works with this kext http://www.kexts.com/view/1378-powercolor_hd4650.html		VGA/DVI/HDMI
HD 4650 (H465fs512)	HIS	Works with these kexts [25] Install with Kext Helper b7		DVI (Dual works *mirrored only*, HDMI (port 1) has static, No HDMI port 2
HD 4670 1GB	Sapphire	Works without any kext. Chameleon v2.0-RC5 r747 GraphicsEnabler=No		DVI/?/?	Not tested
HD 4850 512MB	Asus	ATI48xxInjector.kext[26] placed in E/E Chameleon 2 RC5 r1155[27] with GraphicsEnabler=Yes in org.chameleon.Boot.plist.		DVI/DVI (Both)
Radeon HD 4870	XFX	Works OOB		DVI / DVI	Not tested
HD5450 (EAH5450 512MB)	Asus	Install iatkos s3 v2 without any vga patch update to 10.6.8 Install ATI5000injector.kext to Extra using kextwizard and Fix Permission		VGA/DVI/HDMI ?
HD 5670	Asus	Works almost OOB after a clean install with Leohazard 10.6.2 using latest Chimera or latest bootloader from kabyl. GraphicsEnabler=Yes, UseATIRom=Yes and place your rom in /Extra. Use following rom: [28] Rename to "1002_68D8_03561043.rom".		VGA/DVI/HDMI ?
HD 5670 1GB	Sapphire	After updating to 10.6.8 Combo Update, it works OOTB.		DVI/HDMI/VGA	Not tested
HD 5670	XFX	Works OOB after 10.6.8 combo update.		DVI-Yes HDMI-? Displayport-?	Not tested
HD 5670	XFX	Works fine with ATY_Init.kext.		DisplayPort: Not tested DVI: HDMI: Not tested	Not tested
HD 5750 1GB GDDR5	HIS	works by Adding 0x68BE1002 to Info.plist from ATI5000Controller.kext in S/L/E after combo update 10.6.8, repair cache and permission and rollback USB and then Reboot GraphicsEnabler=Yes		DisplayPort: Not tested DVI: with VGA adapter HDMI:
HD 5770	SAPPHIRE	Works OOB GraphicsEnabler=Yes.		DVI/DVI/HDMI/Displayport
HD 5770	GIGABYTE	Worked OOB after 10.6.8 update from iATKOS S3 v2 10.6.3 clean install. GraphicsEnabler=Yes.		DVI/DVI/HDMI
HD 5770 SL 1GB GDDR5	GIGABYTE	fully working with Netkas 10.6.8 Exotic patch GraphicsEnabler=Yes Running on 2560x1440 (DVI/HDMI/DP) Displayport works only as Slave Sensors also working well with iStats for dual monitor w/HDMI + DVI, set ATI Config to "Peregrine" in boot.plist		DVI/HDMI/Displayport
XFX Radeon HD 5770 1GB DDR5 (577X-ZHLC)	XFX	Works OOB and with GraphicsEnabler=Yes		DVI, DVI, miniHDMI. Works with DVI to HDMI cable too.
HD 5770	XFX HD5770 DP Eyefinity	Worked OOB after 10.6.8 update from iAtkos 10.6.3 clean install.		2xDVI	Not tested
HD 5830	HIS	Use google search		DVI/VGA
HD 5850	Sapphire	works OOB with Chimera Bootloader and GraphicsEnabler=yes DisplayPort is NOT working, just a black screen but it recognize that something was plugged in DVI works just up to FullHD resolution (1920x1080) if you have a resolution above this you have to plug out the cable and plug it back in to have a picture (everytime after booting)		DVI/HDMI	Not tested
HD 5850	Sapphire	works OOB with Chimera Bootloader and GraphicsEnabler=yes copy over all kexts beginning with ATI from a 10.6.7 install and even DisplayPort and resolutions above 1920x1080 will work fine without replugging		DVI/HDMI	Not tested
AMD HD6350 512MB DDR3 DMS59 Connector (HP OEM)	AMD / HP OEM	Install OSX 10.6.x, Update to 10.6.8, Edit and insert Vendor and Device ID's (Dev 68f9, Ven 1002) to both ATI5000Controller.kext and ATIRadeonX3000.kext, install them using Kext Utility. Reboot system, video card will be listed as a HD5000 series, but works 100% with full resolution change and QE/CI. I installed it on an HP DC7900SFF with an edited DSDT and an imac9.1 smbios.plist and graphics enabler=Y.		2 x VGA or 2 x DVI
HD 6750 (1GB)	Sapphire	Chameleon 2 RC5 GraphicsEnabler=No. Not Working Kernel Panic with GraphicsEnabler=Yes Do not recognize VRAM 800x600 Mode only		VGA/HDMI/DVI
HD 6850 (1GB)	Gigabyte GV-R685OC-1GD	Chameleon 2 RC5 AtiConfig=Mangabey AtiPorts=4		2xDVI (tested, dual ok) HDMI, DisplayPort (Not tested)
HD 6850 (1GB)	XFX (Dual Fan)	Chameleon 2 RC5 GraphicsEnabler=Yes. Fully Works		DVI/DVI HDMI/DisplayPort
HD 6450 1GB	Generic	Full Works(10.6.8) but Hdmi contection turns the tv to green colour(VGA full ok).		DVI/DVI HDMI/DisplayPort	Not tested
HD 6450 1GB DDR3 PCI-E	XFX	Full Works(10.6.8) VGA, HDMI, DVI full works. Placing RadeonHD ketx in Extra Folder		DVI/HDMI/VGA
HD 6450 1GB DDR3 PCI-E	Sapphire	Chameleon 2.x, Chimera 1,7 or Clover OK GraphicsEnabler=Yes AtiConfig=Ipomoea AtiPorts=3 GraphicsEnabler=No (patched ATI6000Controller.kext framebuffer) http://www.osx86.net/view/3332-ati_shappire_hd_6450_1gb_ddr3_pci-e.html AtiConfig=(Bulrushes, Cattail, Duckweed, Elodea, Fanwort, Gibba, Hydrilla, Ipomoea, Lotus, Muskgrass and Phitecia) AtiPorts=3 Full Works with DSDT HDMI Injection and framebuffer patch		DVI/HDMI/VGA

NVIDIA

Model	Board-Manufacturer	Notes	QE	Output	Dual display	32/64bit
NVIDIAGeforce 7900 GT 256MB DDR3	XFX	Working With GraphicsEnabler=no and NVEnabler64 with full resolution. Haven't tested S-Video out. Not sure About 64 bit.		DVI/DVI/S-Video
NVIDIAGeforce 7800 GT 256MB DDR3	EVGA	Working with GraphicsEnabler=no and NVEnabler64 with full resolution. Haven't tested S-Video out. Not sure about 64 bit.		DVI/DVI/S-Video
NVIDIAGeforce GT 520 1024MB DDR3	Zotac	Not working. I was trying GraphicsEnabler=yes,no and other option. QE - not working. Just 1024x768.		VGA/DVI/HDMI
NVIDIA Quadro NVS 290 256MB DDR2	NVIDIA	NVEnabler64. Graphicsenabler=Yes		dual VGA
NVIDIAGeforce 8400 GS 512 MB DDR2	Gigabyte	Works out of the box. Graphicsenabler=Yes		VGA/DVI/Gameout
NVIDIAGeforce 8400 GS 256 MB DDR2	MSI	Works with Dell GX280 Pentium 4HT type=0f34. GraphicsEnabler=Yes,remove PCIRootUID=1, and use efi studio v1.0 to place info in both (extra & L/Pref/sysconfig/) boot.plist files. Profiler still shows unknown nvidia GPU. QE/CI & Rotation confirmed working.		VGA=Y/DVI=?
NVIDIAGeforce 8400 GS 512 MB DDR3	Zotac	Works with GraphicsEnabler=Yes feels OOB and all features. follow instructions here [29] / if you get Black Screen use Kernel Flag: pciu=1 GraphicsEnabler=yes		VGA/DVI/HDMI
NVIDIA Geforce 8400M GT		Works in Vaio VGN-NR31SR but without acceleration. Full resolution is enabled with Chameleon "Graphics Mode" parameter. It is said that Vaios only support acceleration with external displays. Didn't try too hard, trusted the internets.		VGA	Not tested
NVIDIA GeForce 8800 GTS 640MB	Albatron	Works out of the box		DVIx2	Not tested
GT520 SILENT 1GB DDR3	Asus	Not working!!! Work 10.7.5/10.8		VGA/DVI/HDMI
EN210 SILENT 512 MB DDR2	Asus	Works using EFI string (followed this guide) with DVI-I/DVI-I option in EFI string. Works OOB if suitable DSDT file is provided, with GraphicsEnabler=Yes.		VGA/DVI/HDMI (tested via HDMI->DVI cable)
GeForce 8400 GS	EVGA	GraphicsEnabler=Yes Snow Leopard 10.6.8 NVIDIA ID 10de:06e4		VGA/DVI
GeForce 8500 GT	MSI	Graphics Enabler and NVenabler both work		VGA
Geforce 8800GT	NVIDIA	Works with GraphicsEnabler		DVI/DVI
Geforce 8800GTX	Palit	Works with GraphicsEnabler		DVI/DVI
GeForce 9400GT	XFX	Follow this guide		DVI/VGA
GeForce 9400GT 1Gb DDR2 128bit	Digital Alliance	Works with GraphicsEnabler=Yes, QE just on DVI		DVI/VGA	Not tested
GeForce 9600GSO (512MB)	XFX	GraphicsEnabler=Yes in Chameleon. Add DeviceID to NVAND50HAL.kext and Nvinject 64.kext. Add NVCAP string "BAAAAAAAAwAMAAAAAAAABwAAAAA" to enable usage of the HDMI Port. This also enables the ability to use dual monitors. Keep in mind that this video card does not support DVI to VGA adapters at all, regardless of OS.		1xDVI 1x HDMI
GeForce 9600GSO	XFX	Chameleon GraphicsEnabler		2xDVI
GeForce 9600GSO	EVGA	Custom EFI string ( 768mb, vga/dvi ) (One display will work with nVenabler 64 kext but I was only able to get dual display to work without it and by using a custom efi string from uInstaller)		VGA/DVI (With DVI-VGA adapter on second port)
GeForce 9600GT	EVGA (PNY card works also)	Works with GraphicsEnabler=Yes, full QE/CI and res change. Currently running dual card setup for triple displays with a PNY 9600GT as a second card, with custom EFI strings made using Aquamac method.		DVI/DVI (DVI-VGA adapters work on all ports)
GeForce 9800GT 512MB DDR3	Twintech (GigaByte card should work also)	Works OOB with GraphicsEnabler=No + NVEnabler_64.kext. Full QE/CI + res change + dual-DVI output. PCI vendor id 0x10de, device id 0x0614. Use DSDT injection to avoid NVenabler kext and GE=Yes/No.		DVI/DVI (DVI-VGA adapters work on all ports)
GeForce 120 GT (also known as 9500 GT) 512 MBytes	Apple	With GraphicsEnabler in Chameleon as supplied with Blackosx's boot loader and supporting files. Is working with the Apple LED Cinema 27" display via Atlona Dual-Link to mini-DisplayPort adapter. Works via both direct connection of above monitor to mini-DisplayPort and via Atlona adapter to DVI port (both connection methods working in both Windows 7 and OSX 10.6.8).		DVI Dual-Link/Mini-DisplayPort	(Probably with 1xDVI-M to 2xDVI-F but at half resolution)
GeForce 120 GT 512 MBytes	Apple	WOB on a ASUS P7P55D-E PRO motherboard and core i7 870. Booting with iboot cd and no hacked kexts or chameleon installed on hard drive		DVI Dual-Link/Mini-DisplayPort
GeForce 210 1 GB DDR3 Silent	ASUS	GraphicsEnabler=YES, custom EFI string injected on Boot.plist, you can download here [30] NOTE: The EFI strirng assumes card to be in PCI SLOT 1/0/0, which is the ones on gigabyte motherboard. Find out where is yours if it doesnt work, and modify supplied graphics.plist , then convert to HEX with GFXUTIL tool (look in this forum, very easy), and last substitute your customized hex lines in the boot.plist		DVI/VGA/HDMI
GeForce 210 512 Mb DDR3 Silent	ASUS	GraphicsEnabler=YES and nothing more		DVI/VGA/HDMI
GeForce 210 1Go DDR3 Heatsink (no fan)	Twintech	Works OOB with GraphicsEnabler=YES. That's all		DVI/VGA/HDMI
GeForce GT 220 1 GB DDR2	GigaByte	NVenabler.kext, no GraphicsEnabler in Chameleon		DVI/VGA/HDMI
GeForce GT 220 1 GB GDDR2	ZOTAC	Install NVenabler.kext use Chimera and set GraphicsEnabler=No		DVI/VGA/HDMI
GeForce GT 240 512 GB GDDR5	GigaByte and PNY DDR3	Works with NVenabler.kext or graphics enabler=yes (chimera efi) Important i already use this 2 cards in hackintosh and dont work 100% right you can see this in photoshop open a picture press f 2 times,them h, now move picture with mouse and see that the picture blink or movements are not syncro with mouse but if you use a real mac or use other cards like 9800gt, 250gts or 8600gts you dont have those kind of problems really is a problem if you use photoshop or photo edit software take care. and with enabler gpu is unknow in graphics info and dont use nvidia rom from card. i dont understand why tonys recomend this card i already try everything and dont work at 100%		DVI/VGA/HDMI
GeForce GTX260 216SP OC	GigaByte	NVenable + CUDA drivers + GT200Driver.pkg for Full suport CUDA		DVI/DVI VGA/VGA With Adapter
ZOTAC GTX260 216SP	ZOTAC	NVenabler + 64-Bit GraphicsEnabler=No		DVI/DVI VGA/VGA With Adapter
GeForce GTX285 1GB	Palit	Works OOB		DVI/VGA/HDMI
GeForce 7300GT 512Mb	Asus P5KPL	GraphicsEnabler=Yes		DVI/VGA
GeForce 7200GS 256Mb	Gigabyte G31M-ES2C	GraphicsEnabler=Yes + EFI String Injection		DVI/VGA
GeForce GTX 460 Sonic 1GB	Palit	Used Official NVIDIA Drivers + Chameleon 2.0 RC5		DVI/VGA (HDMI not tested)	Not tested
PCYES R7 260X OC Dual Fan 2GB GDDR5 128Bits FanID=6658 https://www.tonymacx86.com/threads/success-ga-z77-d3h-amd-radeon-r7-260x.183213/page-4	Palit	Used Clover Inject Fake ID 6640		DVI-D/DVI-I dual Display 100% Patched use FB Baladi	100%

Network Cards

Wireless

Interface	Standard	Device	Manufacturer	Chipset	Notes	32/64bit working with patch
PCI	b/g	Maxg	US Robotics	Broadcom 4318			?
PCI Express	b/g/n	PCE-N13	Asus	Ralink RT2860	driver [31]
USB	b/g/n	EUB9707	EnGenius	Ralink RT2870	driver [32]
USB	b/g/n	WUSB600N	Linksys	Ralink RT2870	driver [33]
PCI-E 1x	b/g/n	TL-WN781ND	TP-Link	Atheros 9285	During iAtkos s3v2 customize install, check the atheros wireless kexts, detected as airport extreme, so it nearly OoB. then update to 10.6.8. PS: somehow it will not connect when the network security is WPA2, only works on WEP
USB	b/g/n	DWA 140 (HW:B2 FW:1.70(E))	D-Link	Ralink RT2870	driver [34] (be careful not to install other drivers, otherwise the official one won't work. When the official one is installed, there may be problems if you try to change the WINS or DHCP ID: the Wireless Utility will quit right after started, and this can be solved only by reinstalling the OS afaik. The problem survives reboot and driver reinstallation.)
USB	b/g/n	RNX-N150UBE	RoseWill	?	Use Driver off of Rosewill's website. install and restart.
USB	b/g/n	RNX-N600UBE	RoseWill	Ralink RT3572	Use Driver Found Here: http://www.mediatek.com/_en/07_downloads/01_windows.php?sn=502. Driver Version 4.2.6.0. Install driver with out plugging in device, restart and plug in device. NOTE: uses Ralink Wireless Utility not apple airport.
Mini-PCIe	b/g/n	AR9280	Atheros	AR5B91	Detected as AirportExtreme		?
USB	a/b/g/n	W522U	Tenda	Ralink RT3572	PCI device:0x3572 vendor id:0x148f. Use driver v3.0 provided with device or look at [35]. Use Ralink wireless utility to configure. Seen as "802.11n WLAN" USB device, not as Airport device.

Wired (Ethernet)

Interface	Standard	Device	Manufacturer	Notes	32/64bit working with patch
PCI	10/100/1000	GA311	Netgear	Works OOB. Based on the Realtek 8169 chip that is used in several Macs, so no additional kexts or anything are required. $8 shipped on eBay, definitely worth plugging it in and having it just work.
PCI	10/100/1000		Ovislink	Works OOB. Based on the Realtek 8169 chip that is used in several Macs, so no additional kexts or anything are required.

Sound Cards

Interface	Hardware Name	Manufacturer	Notes	32/64bit working with patch
Firewire	Ultralite MKIII	Motu	Works OOB
Firewire	Traveler MKIII	Motu	Works OOB (Install "MOTU Audio" software)		?
Firewire	8 Pre	Motu	Works OOB (install MOTU software)
USB	Fireface UC	RME	Works OOB
PCI	Multiface	RME	Works OOB with "hdsp_173_x86" driver; must boot system in 32bit mode! Driver no longer available from RME but can be found here		?
USB	Audio 2 DJ	Native Instruments	Works OOB with newest official drivers
USB	Fast Track USB	M-Audio	Works without any issues
USB	Aureon Dual USB	Terratec	Works OOB
External Soundcard (USB)	UA-1EX	EDIROL	Works with Driver from Edirol site, and on disk on 10.5x to 10.6.8
USB	Sound Blaster Extigy	Creative Labs	2-channel works OOB; 5.1 unknown
PCI	Sound Blaster Audigy/Audigy 2	Creative Labs	stereo 32bit works with lion kx driver; no input; look for dmg with lion permission fix included; 64 bit lion
USB	Sound Blaster Audigy 2 NX	Creative Labs	Works OOB. AC3/DTS passthrough via S/PDIF doesn't work.
USB	H4n	Zoom	Works OOB without issues.
USB	iMic	Griffin	Works OOB without issues.
Firewire	Firewire Audiophile	M-audio	Works with driver from M-Audio (tested on 10.6.8)
USB	Komplete Audio 6	Native Instruments	Works with driver from Native Instruments (tested on 10.6.8)
USB	US-1641	TASCAM	Works with driver from TASCAM v2.00 (tested on 10.6.8)		?

Other Accessories

Type of Accessory	Item Description	Manufacturer	Notes	32/64bit working with patch
Firewire Adaptor	Adaptec AFW-4300C PCI Firewire card	Adaptec	Worked OOB under 10.6.8		?
Bluetooth Trust 2400P v04	Bluetooth Dongle	Connectland
Bluetooth USB micro adapter	Bluetooth Dongle model RF-MRBTAD	Rocketfish	Works OOB. Cheap on the used market!
Bluetooth USB micro adapter	UB-110 Class1 Bluetooth Dongle	Ultron	Works OOB.
USB to 36 Pin IEEE 1284 Parallel Printer Cable adapter	Product ID:0x2305, Vendor ID:0x067b	Prolific	Works OOB. Bought on eBay, item code "DX0052".
Wireless headset	Creative HS-1200 USB	Creative	Works OOB.
Bluetooth USB micro adapter	SiteCom CN-516 Micro Bluetooth 2.1 Adapter	SiteCom	Works OOB
Bluetooth USB micro adapter	Digitus DN-3021	Digitus	Doesn't work! It isn't even recognized as Bluetooth device..
Bluetooth USB micro adapter	F8T016ng	Belkin	Works OOB
USB Webcam	High Def Webcam	ASDA Supermarket (UK)	Works OOB. 10Pounds Own brand
Sata Controller	RocketRaid 2300	HighPoint	Works
USB Webcam	Genius iSlim 320	Genius	Works OOB. Product ID:0x605e, Vendor ID:0x0458 (KYE Systems Corp.), Manufacturer: PixArt Imaging Inc.
3D Screen	Flatron D2242	LG	Works OOB. 3D passive technology make possible 3D youtube movie clips and others. You need to be connected with HDMI or 3D will not work. Cheap but nice screen (1 pair of glass included and one to put in front of your regular glasses. use "BINO" which is a great freeware (with a lot of included format and subtitles support). Being 32 or 64bits here has no importance at all