Note: Because of the introduction of the Macintels, this list can also be used for hardware that you have tested with the new Macs! Just make sure that you let us know you're using it on an Apple machine.
This is a component level hardware compatibility list. We want to keep it as accurate as possible, but please, do not entirely rely on this list when buying hardware. Add which parts you have working in the categories listed below, or create a new category. Please keep alphabetical order inside the categories. The categories themselves are ordered by popularity. Please list any caveats or problems as well.
- ONLY add hardware that you have TESTED. Don't add hardware just because you think it might work.
- Please add hardware into tables.
- This is for 10.4.6 builds only.
Please specify if your card is AGP, PCI or PCI-E.
Also, please try to differentiate chip and board manufacturer (i.e. "ATI / Sapphire" or "NVidia / Gainward").
Note: For NVidia users, visit http://macvidia.starchaser.org/ for updated drivers. For NVIDIA CARDS PLEASE SPECIFY IF THE CARD DOES QE/CI. Saying the macvidia drivers work but not specifying QE or CI is a bit misleading
Note: For ATI users, visit http://omni.starchaser.org/ for experimental drivers.
Note: As of right now, all ATI cards with working kexts have severe slowdown issues with nForce3 chipsets. There is no fix for this, save getting editting out your card from the kext or using Quartz Debug to shut off Quartz Extreme.
UPDATE: ATI Radeon 9600 working on nforce3 with QE and CI with no slowdown, only some little tearing that could be fixed, instructions here. This might work with other cards.
|Hardware Name, [Bus] [(VRAM)]||Chip-Manufacturer / [Board-Manufacturer]||Notes||QE / CI||Resolution||Full Work / No Patch|
|PowerColor X1600PRO 256MB||PowerColor / ATI||works with Borisbadenov method Driver @ http://www.installers.dl.am/||YES||ANY||Only DVI to VGA on one Monitor, anything else works fully|
|X1600Pro IceQ PCIe 256MB||HIS Excalibur / ATI||works with Borisbadenov method Driver @ http://www.installers.dl.am/||YES||ANY with DVI support||Yes / Borisbadenov Patch 3.2 for 10.4.6|
|ATI Radeon X600 256mb||ATI||10.4.6 Goatse image works 1024x768 only out of box. Can get full resolution/refresh rate control panel with Callisto drivers, but must do QE/CI hack/trick to get QE/CI working again after callisto installation. World of Warcraft works perfectly after callisto installation / QE/CI patch/hack. See solutions in insanelymac forum to deal with mouse tearing.||YES||1024x768 60hz QE/CI only out of box. Callisto driver needed for resolution/refresh rate control plus QE/CI hack needed to re-enable after callisto driver install.||Only|
|PowerColor X1600XT256MB||PowerColor / ATI|| This card works perfect, all I did was edit the ATINDRV.kext and replaced
"<string>ATY,Wormy</string> to this <string>display</string>"
<string>IONDRVDevice</string> to this <string>IOPCIDevice</string>
. After these changes I could choose any resolution in DISPLAY Preference, and I have full support for QE and CI
|YES||ANY||just the one mentioned before|
|PowerColor X1600XT 256MB dual-DVI-D PCIe||PowerColor / ATI||Works with Borisbadenovmethod Driver @ http://www.installers.dl.am/ yielding QE/CI, full resolution support, refresh-rate selection, no mouse tearing, and screen rotation. Full-screen video at 1920x1200 is smooth, full 32-bit color appears to be present - this has been an issue on other cards. However, the card will only send output on the primary DVI-D port; if D-SUB is attempted in conjunction with DVI-D, output is only sent on D-SUB. Thus no dual-monitor support is possible with (at least) dual DVI or mixed DVI/D-SUB. I have not attempted dual D-SUB.||YES||ANY||NO|
|MSI RX1600 TD256E 256mb||ATI / PCI-E||works with Borisbadenovmethod Driver @ http://www.installers.dl.am/
Full QE/Ci, able to change resolutions, refresh rates, no mouse tearing.
|Yes||Any||Patch and 100%|
|ATI Radeon X1600 Pro 512mb||ATI / AGP||works with Borisbadenovmethod Driver @ http://www.installers.dl.am/
Full QE/Ci, able to change resolutions, refresh rates, no mouse tearing.
|Yes||Any||Patch and 100%|
|HIS Radeon X1600XT IceQ Turbo 256MB||ATI / PCI-E||Recognized as VESA 3.0 with full QE/CI and Q2DE supported. Unable to change resolution or refresh rate, minimal mouse tearing that was corrected with mousepose. Used borisbadenov method installer, then ran the uninstall script and everything wored.||Yes||Any||Patch and 100%|
|Radeon X1800XT PCIe 512MB||ATI / ATI||works with Borisbadenov patch, no DVI (have to use VGA adapter)||Yes||Any||No, had to patch|
|Radeon X1800XT 256MB||Sapphire / ATI||Make sure to use version 3.2 of the Borisbadenov/NeoPheus drivers- v3.6 gives Resolution change but NO QE/CI. Drivers here->||Yes! (With v3.2)||Any||No|
|FireGL V5000 PCI-E||ATI||QE and CI supported after patch. 1024x768 resolution only in system prefs. See also http://forum.osx86project.org/index.php?showtopic=10415&hl=ati. With 10.4.4 Ext,Framw,GL files. Some mouse artifacts, fix it with mouse locator. Edit com.apple.Boot.plist to get resolutions other than 1024x768.||Yes||Tested with 1280x1024|
|Sapphire X1300XT 256MB||Sapphire / ATI||Full works: QE,CI,Rotating,Gamma and color adjustments,maybe multidisplay (i dont test it). Check: borisbadenov ATI X1000-series Solution, Full ATI Support with Apple Drivers (Post #820).||Yes||ANY||Yes|
|Radeon X300SE||ATI||Supports QE/CI in any resolutions, with Callisto 008 and Koverg driver/patches, leaves mouse trails that can "patchsolve" with MouseLocator (Device ID = 5b60). However, under DVI-D, the full-screen video is very choppy with this card at high-resolution; Aperture is often sluggish when it animates (switching picks in a stack, etc.); the card *does not* support full 32-bit color, although it claims to under Display Preferences. Not a good choice if you're looking to purchase a new card for your system.||Yes||Any||No|
|Radeon 9000 IGP||ATI||Works in 1024x768 with no patch and works with Omni Castillo driver version 003 (fails with 006) for higher resolutions||No||1280x800||No|
|Radeon 9000 AIW AGP||ATI||Works with no patch in 1024x768 and without mouse artifacts! Not tested any drivers tweak to set higher resolution in System Pref.||No, uses the ATIRadeon8500.kext so no QE/CI implemented||1280x1024 and 1024x768 tested OK, but seems unable to change refresh rate||No|
|Radeon 9800Pro AGP||ATI||Working. Use Callisto (omni.starchaser.org) to enable Display options. QE/CI Working. Remember to edit AtiRadeon9700Ga.plugin when using Callisto to enable QE/CI. Moderate mouse tearing can be decreased with MouseLocator||Yes||1280x1024||Needs Callsito to enable display adjustments in control panel. Has moderate mouse tearing|
|Radeon 9800 Pro AGP 128MB VRAM||ATI||Working on SSE2 (with SSE2 patches, DVD already patched). Didn't do anything special but limited to 1024x768x32. QE/CI Working. Also there is mouse tearing. Tried Callisto8+Koverg patch, which killed my installation. So go get higher resolution, I simply edited (see below) the com.apple.boot.plist file to add 1280x1024x32, which works beautifully!
Add to library/Preferences/SystemConfiguration/com.apple.boot.plist (sudo library/Preferences/SystemConfiguration/com.apple.boot.plist )
<key>Graphics Mode</key> <string>1280x1024x32</string>
|Yes||1280x1024||Simple install with pre-patched DVD with great. Edited boot.plist just for high resolution|
|Radeon 9600 PRO SE AGP / 128MB||ATI / Sapphire||Doesn't need a patch up to 1280x1024. Running 10.4.6 with Callisto b008 video - no tearing. Perfect 1920x1200 on Dell 2405 Widescreen LCD.||Yes, but tearing then.||1920x1200||Needs Callsito to enable display adjustments in control panel.|
|Radeon 9600SE AGP||ATI / Sapphire||Doesn't need a patch.||No||1024x768||No|
|Radeon 9600SE AQ 128mb AGP||ATI||QE and CI working. Install instructions here||Yes||1280x1024||No|
|Radeon 9800SE 128mb AGP||Sapphire||QE and CI working natively. Resolution change with Callisto b3. Mouse tearing mostly fixed with mouse locator||Yes||1280x1024||No|
|ATI Radeon 9200 SE (128 MB)||ATI / Gigabyte||works||NO||1024x768 (OSX default)||Patched the plist for 1280x1024x32|
|Radeon X800 Pro AGP||ATI||QE / CI enabled in JaS 10.4.6 using Callisto b006, modifying the appropriate ATIRadeon9700GA.plugin using the methods described in the Callisto package, by adding AGPGart and by (as odd as it sounds) replacing the following files on my OS X istall with their respective files found on the install CD: All ATI* kext files and the entire OpenGL.framework found in the SystemEssentials directory. Extraction completed using Pacifist. Finally Disk Utilities -> Permissions Repair was run. More info on the method I used HERE.||Yes||Any||Method listed in descriptions gave me 100%!!!!|
|Radeon X800 Pro 256MB 256-bit GDDR3 VIVO PCI-Express||ATI / Sapphire||QE/CI needs John Koverg's patch (http://forum.osx86project.org/index.php?showtopic=10415). Edit com.apple.Boot.plist to get resolutions other than 1024x768.||Yes||1280x1024||No|
|Radeon X800XL 256MB 256-bit PCI-Express||ATI / Sapphire||With 10.4.4 Ext,Framw,GL files. Some graphics artifacts. QE/CI needs John Koverg's patch (http://forum.osx86project.org/index.php?showtopic=10415 ). Omni Castillo driver version 007 for higher resolutions.||Yes||Any||No|
|Radeon X550XL 256MB 256-bit PCI-Express||ATI / Sapphire /Asus||Works at 1024x768 resolution after stock 10.4.6 Goatse.cx DVD install and at [email protected] on Asus LCD PW191, DVI digitalLCD, OSX10.4.6DVDinstall. Full CI/QE, Q2D, OpenGL with Omni Castillo driver (008, CallistoFB), any resolution. With mouse tearing. Vendor 0x1002 (ATI), Device ID 0x5b63||Yes, but tearing||Any||Needs Callsito to enable display adjustments in control panel.|
|Radeon RV100 (old)||ATI/ST Lab||No openGL support, very, VERY slow||Yes||[email protected]||No|
|Radeon 9600 256 MB||ATI / Rosewill||Didn't have to patch..leaves mouse trails.||Yes||1280x1024||Yes|
|Radeon X300 mobility 64MB||ATI||After patching ATIRadeon9700.kext QE and CI works, leaves mouse trails||Yes||hard set 1400x1050||Yes|
|Radeon x1600pro 256M||ATI / Sapphire||QE/CI needs pach atix1000.kext. Edit com.apple.Boot.plist to get resolutions other than 1024x768.||Yes||1280x1024||No|
|Radeon x1600Pro 256M||ATI / PowerColor||Use borisbadenov's ATI fix and must switch to ATINDRV from 10.4.5, otherwise artifacts and crashes. Now works great except no energy saving, DVI or dual monitor.||Yes||Any||No|
|Radeon x1600xt 256M||ATI / Sapphire||Use borisbadenov's ATI fix. For Sapphire, use DVI to VGA and Sleep function works!||Yes||Any||No|
|Radeon x1600 PRO 256M||ATI / Sapphire||Use borisbadenov's ATI fix||Yes||Any||No|
|Radeon x1600XT 256M||ATI / ASUS||Use borisbadenov X1xxx fix. Works perfectly except no dual monitor. Can use DVI-out and sleep. For later versions of the Asus EAX1600XT with the Tv out port (comes with a purple cable) use the method described at [[this link.]http://forum.insanelymac.com/index.php?showtopic=23809]. Note from another user: This video card has been nothing but a nightmare for me - it does not work as claimed.||Yes||Any||No|
|Radeon 7000||ATI / ASUS||Use Callisto b0003. b0008 doesnt seem to work.||Any||No|
|AGP Radeon 9550 256 MB||ATI /Sapphire||Change in : Edit com.apple.Boot.plist to get resolutions other than 1024x76. For How to ? Go to Trips and Tricks||Yes||[email protected]||Yes|
|AGP Radeon 9550 256 MB||ATI /Gecube||needs Callisto Driver to change resoluion. editing Boot.plist doesn't work. Leaves mouse trails||Yes||1280x1024||Yes|
|AGP Radeon 9550 128 MB||ATI / MSI||Silent, without cooler edition. Required Callisto Driver b008 to change resolution, no pivot support, disable energy saver function - system does n't wake up||Yes||up to 1280x1024||Yes, after ATIRadeon9700.kext correction|
|Radeon 9600 128 MB||ATI / Gigabyte||Didn't have to patch..leaves mouse trails.||Yes||1280x1024||Yes|
|Radeon 9600XT 256 MB with DDR2||ATI / Sapphire||QE/CI works out of the box. Some graphical tearing after playing games, but nothing unbearable||Yes||1280x1024||Yes|
|Geforce Go5200 32MB||Nvidia||MacVidia Driver required for non-standard widescreen resolution||No||1280x800||Yes|
|Geforce FX5200 128MB AGP||Nvidia||MacVidia Driver required. Currently using v1.07||No||[email protected] (up to [email protected])||Yes|
|BFG FX5500OC 256MB PCI||nVidia/PCI||Recognized as VESA v3.0, Macvidia enables 2D Hw acceleration||No||[email protected] w/o macvida, card maximum with macvidia||No|
|Geforce FX5200 128MB AGP||Nvidia||Slower results from macvidia v1.07 than the original drivers, so using the installation drivers, wired||No||[email protected]||Yes|
|Geforce FX5200 128MB AGP||Nvidia/Chaintech||Works on 1024x768 without drivers, more resolutions with Macvidia Drivers 1.081||No||Using [email protected] (up to 2048x1536 @60)||Yes|
|Geforce FX 5500 OC 256MB AGP||Nvidia/BFG||Works fine with Macvidia Driver Beta 2 b1.||No||[email protected]||Yes|
|Geforce 4 MX 420 64MB||Nvidia||Didn't have to patch.||No||1024x768||Yes|
|855GM||Intel||Works out-of-the-box with default VESA driver. No nice features, though VLC with the SDL drivers works brilliantly.||No||1024x768||Yes|
|915GM||Intel||Boot only if an external monitor (or TV by S-Video) is connected.Update: for laptops with vga-out you can use Pagrus-methode:http://forum.insanelymac.com/index.php?showtopic=18797&st=0&gopid=147942&#entry147942||Yes||1280x800||No|
|eVGA 7600 GT, 7800 GT, PCI-e, 256MB||nVidia / eVGA||No patching from JaS release.||No||1280x1024||Yes|
|eVGA 7900 GT Signature Edition||nVidia||Macvidia 1.0.8 Drivers||No||1280x1024||Yes|
|GeForce 7800 GT, PCI-e, 256MB||nVidia / ASUS||Works fine with Macvidia Driver||No||Any||Yes|
|XFX 7600 GT, PCI-e, 256MB||nVidia / XFX||Download & Install MacVidia 1.0.8 Driver||No||All||Works 100%|
|6800 gs pci-ex||nVidia||drivers from macvidia for widescreen||No||1440x900||Yes|
|6600 Go MXM||nVidia||drivers from macvidia, need to add DEV ID in NVidiaHAL.kext||No||1400x1050 @75Hz||Yes|
|Diablotek's nVidia GF 6600||Diablotek/nVidia||Works perfectly, no special instalation instructions||No||[email protected]||Yes|
|Gainward 6800GS 512MB||nVidia||Installs fine -haven't tried drivers from macvidia yet hence the low resolution||No||1024x768 @60Hz||Yes|
|PNY 6800GS AGP||nVidia||With MacVidia nVidia Driver 1.0.8 all resolution is available||No||Any||No|
|EVGA 6800GS 256MB AGP||nVidia||Macvidia beta 2 build 2 drivers install w/o a hitch||No||[email protected]||Yes|
|Leadtek A6600GT AGP||nVidia||Works with stock apple drivers(of course), but artifacts when MACVIDIA Drivers are applied and the resolution is changed||No||1024x768||Yes, with stock apple drivers.|
|PNY 6600GT PCI-E 16x||PNY/nVidia||Works with Beta2 Build1 MacVidia drivers.
Any resolution (800x600 to 2560x1600) with full DVI working. VGA works with DVI2VGA adapter.
|No||ANY||Needs MacVidia Drivers. DO NOT use the installer! Follow Beta2 Build1 instructions in the TUTORIAL section.|
|nVidia GeForce 6100||nVidia||This card works well with MacVidia Drivers (Tested Beta 2 Build 1) Max Resolution is 2560x1600. Tested up to 1600x1200 75hz. Vesa 3.0 This card is built into many newer prebuilt computers and motherboards.||No...||[email protected]||Yes|
|EVGA GeForce 7300GT 256MB||EVGA / nVidia||2D Hardware aceleration works. Native drivers works ok. With MacVidia drivers need to set Graphics Mode to boot after can set any resolution, else black screen.||No||ANY||Yes|
|nVidia GeForce 7950GX2||nVidia / XFX||This card works with MacVidia Drivers (Tested Beta 2 Build 1). Test with Sony 19" DVI/DFP
I had to install using an ATI Radeon 7000 (PCI) then install the MacVidia Drivers and the 7950GX2
|Club3d 6600GT PCI-E 16x||nVidia||Works with Beta2 Build2 (1.0.7) MacVidia drivers.
Any resolution with full DVI working. DSUB works also.
HOWTO install: On download page
|No||ANY||Needs MacVidia Drivers. No need to set device id|
|Inno3D 6500 PCI-E 16x||nVidia||Reconized as VESA 3.0
Produce undesire color band when use with Macvidia driver
Work fine w/ DVI. DSUB works also.
|Not test||1024x768, 1280x1024||No Patch w/ HotISO disk|
|nVidia GeForce Go 7600||nVidia||This card works great with the MacVidia drivers (Tested 1.0.8). Test on an HP dv8327cl laptop (17" LCD)||No||Tested at:
|ATI Radeon Xpress 200 PCI-E||ATI||Doesn't work with CI/QE, can get resolution changing with Callisto B3.|
|XFX Nvidia Geforce 6600GT 128mb AGP card||XFX||works with macvidia 10.0.8 without QE and CI all resolutions available after macvidia driver find this driver @ http://macvidia.starchaser.org/||NO||ANY||DVI works with single monitor Dual didnt test|
|Geforce 8800GTS 640MB||EVGA||Hangs on boot||No/No||N/A||NO|
|Nvidia GeForce FX 5200 PCI||PNY/NVIDIA||Poor Graphics (unrecognized) is there a Pacth?||N/A||N/A||N/A|
Network Cards - Wired (Ethernet)
|Hardware Name||Manufacturer||Notes||Fully working without patching|
|RTL8169/8110||Realtek||Only tested with 10 and 100Mb/s network, but it should work in a 1Gb/s network.||Yes|
|Surecom EP-4904SX||Surecom||connected and work: so easy.||Yes|
|BCM5751||Broadcom||Needs Hater's method to make it works. See forum (or message)||No|
|F5D5000||Belkin||Auto Detected,works great, this version is a few years old, the pict on their site now looks like a different chipset||Yes|
|TrueMobile 1300, 1400, 1450||Dell||The 1350, 1370 cards should work too.||Yes|
|D-link DFE-538 TX||D-link||Works Flawlessly, detected automatically, IPv4 setup via DHCP works great||Yes|
|FA311, FA310TX||Netgear||Detected Automatically, defaults to DHCP||Yes|
|PRO/100||Intel||Intergrated Ethernet Card.||Yes|
|PRO/100 VE||Intel||Intergrated Ethernet Card. Requires change to the IONetworkingFamily.kext/Contents/PlugIns/AppleIntel8225x.kext file.
You must add a device ID of 0x10928086
|nForce3 Onboard Ethernet||Nvidia||Forcedeth kext||No|
|nForce4 Onboard Ethernet||Nvidia||tested on Asus A8N-SLI board Forcedeth kext||No|
|Via Rhine II Onboard Ethernet||Via||Works fine with http://www.pinxue.net/mac/viarhine.tar.gz||No|
|Fast Ethernet (3c905B-TXNM) Parallel Tasking II||3com||Works excellent, no problem, PCI Slot||Yes|
|Marvell Yukon 88E8053 PCI-E Gigabit||Marvell||Used Jas 10.4.6 Install DVD
(This is the second onbaord gigabit on A8N32-SLI Deluxe boards)
Network Cards - Wireless
|Interface||Standard||Device||Manufacturer||Notes||Fully working without patching|
|PCI||g||F5D7000||Belkin||Need to disable the Plug and Play BIOS and Change BSD Name to en1 instead of en0 and change IOInterface - integer to 1 in NetworkInterfaces.plist||No|
|PCI||g||F5D7000||Belkin||Works fine, making sure that you tick the install wireless cards drivers on the 10.4.6 JaS DVD. Also works with WPA although it says that it isn't supported...||Yes|
|PCI||g||TEW-443PI||Trendnet||Working with Apple driver. Has to be Plugged/Installed after other wired LAN, Atheros Chipset||Yes|
|PCI||g||F5D7001||Belkin||Broadcom chipset. Recognized as Airport Express right away on 10.4.6 with JaS Patch||No|
|USB||802.11b/g||F5D7050 Ver. 2||Belkin||Used 10.4.6 JaS and installed this Ralink 11g-RT2500 Driver.Plug it in and everything is ok, I just use WEP.||No|
|USB||g||F57050 V 3000||Belkin||Download[] Plug in Adapter after Driver install and you are ready to go.||Yes|
|USB||g||F5D5070 V4||Belkin||Download [Zydas UB Driver]. Follow the [instructions]||No|
|USB||g||DWL-G122 ver. B1||D-Link||See latest 29/11/05 RT2500 OSX 10.4.x USB Driver at Ralink. Needs to unplug/plug USB after every reboot(for solution, check this forum out)||No|
|USB||g||DWL-G122 ver. C1||D-Link||See latest 07/04/06 RT71W OSX 10.4.x USB Driver at Ralink.||No|
|USB||g||WUA-1340||D-Link||download ralink drivers: RT2571W/RT2671:126.96.36.199 RT2500:188.8.131.52||No|
|PCI||b g||DWL-G510||D-Link (Atheros Chip)||Take IO80211Family.kext and IONetworkFamily.kext from 10.4.5 to get to work. Edit /Library/SystemConfiguration/NetworkInterfaces.plist (see forum)||No|
|PCI||b g||DWL-G520||D-Link (Atheros Chip)||Rev A/1 Take IO80211Family.kext from 10.4.5 to get to work.Detected as Airport.You may need to edit /Library/SystemConfiguration/NetworkInterfaces.plist (see forum)||No|
|PCI||g||DWL-G520+||D-Link||rev a3 (i think that mean that all Rev A doesn´t work)||No|
|PCI||g||DWL-G520+||D-Link||only for revb ,not for revc.config on en1||Yes|
|USB||g||CWD-854 Rev. F||C-Net (Ralink Chip)||Install driver RT71W (RT73) from Ralink ||Yes|
|USB||g||ZD1211||DYCON, GIGAFAST, AIRLINK 101, Digicom and many More (ZyDAS ZD1211 Chip Based)||Install driver for 1211 from ZyDAS (Mac 4.5.7 Universal) currently hosted by Zyxel. Works really, really well.And cheap too.||Yes|
|mini PCI Express||a/b/g||AR5006EX||Atheros||Take IO80211Family.kext from 10.4.5 to get to work.||No|
|USB||b/g||US54G||MSI||uses ralink 2500 USB driver||No|
|mini PCI||a/b/g||TrueMobile 1450||DELL||Broadcom BCM4309M chipset||Yes|
|PCI||b/g||WMP54G||Linksys||For the card that uses the Broadcom 4320 chipset, adding the proper string to IO80211Family.kext makes it airport compatible||sort of, it works out of the box but airport reports not configured so you are limited to one permanently set AP until changing the strings in IO80211Family.kext.|
|PCI||b/g||WMP54GS||Linksys||Works (Required minor script editing in Networkinterfaces.plist file to make
it Airport compatible), tested with WEP. SeeFullmetal's post for details.
|Yes. But minor script editing required.|
|USB||g||WUSB54Gv4||Linksys||Ralink Drivers and instructions from Tush/Kramer||No|
|PCI/PCMCIA||g||WG311T, WG511T, WAG311||Netgear||Detected as Airport card. Nice. May have issues with Airport status icon not showing after reboot, but card works perfect. Enable status icon in System Preferences.
For Netgear WG311T Users - Check Out: http://forum.insanelymac.com/index.php?showtopic=16513&st=0 for instructions on how to get the Netgear WG311T working!
|PCI||g||SMCWPCIT-G EU||SMC||Detected as Airport card. Nice.The card works perfect. Go to System Preferences for configuration and enable status icon. User #2 - This card DOES NOT work even after fiddling with settings - see Insanelymac.com||Yes|
|Mini-PCI||b/g||BCM94306 Rev. 4||HP/Broadcomm||Detected as Airport card.The card works perfect, AFTER installing JaS 10.4.6 Wireless Network Fixes (included in JaS 10.4.6 install DVD). Status icon appears upon reboot, configure from there. Tested on HP Pavilion dv1000 series notebook computer. Wireless reception excellent.||Yes|
|PCI||b/g||WLI2-PCI-G54S (Wireless-G 125 High Speed)||Buffalo||Plug-and-play. Recognized as AirPort Extreme. Broadcom chipset.||Yes|
Other Expansion Cards
|Hardware Name||Interface||Device||Manufacturer||Notes||Fully working without patching|
|Belkin USB 2.0 & Firewire 6 ports pci card||PCI||USB 2.0 & Firewire 6 ports pci card||Belkin||work fine. Networking over Firewire not tested.||Fully ?|
|SYBA PCI to Firewire 1394a 3+1 ports controller card||PCI||SD-NEC-4F||NEC||Networking over Firewire (RFC 2734) does not work. If you connect a firewire cable from the OS x86 PC to a Mac, the PC will shutdown abruptly.||Partially, since firewire networking doesn't work (even under Windows)|
|Adaptec FireConnect||PCI||AFW-4300CS||Adaptec||Firewire hard drive works; Firewire connection to digital camcorder works; Firewire networking not tested.||Yes|
|Adaptec 2906||PCI||AVA-2906 50-pin Fast SCSI controller||Adaptec||Not recognized.||No|
|Adaptec 2940UW pro||PCI||AHA-2940UW Pro Wide SCSI Controller||Adaptec||Not recognized.||No|
|Adaptec 19160||PCI||ASC-29160 Ultra 160 SCSI controller||Adaptec||Not recognized.||No|
|Adaptec 29160||PCI 64/66||ASC-29160 Ultra 160 SCSI Controller||Adaptec||Not recognized.||No|
|HAMA USB 2.0 (3-port) + IEEE 1394 Firewire Combo Card (2-port)||PCI||SD-NEC-4F||NEC||Firewire Network doesn´t checked, but Firewire was found, USB working fine||Partially, Firewire works fine under WinXP|
|ADS Tech Pyro PCI64||PCI||Pyro PCI64. Texas Instruments Chipset.||ADS Tech||The only firewire interface I have tested that works perfectly with an external firewire audio interface. No glitches, no noises and stable in Logic Pro 7.2.||Yes|
|Device||What||Interface||Manufacturer||Notes||Fully working without patching|
|Belkin Bluetooth USB Adapter||Bluetooth USB Adapter||USB||Belkin||Full functionally, supported by OSX.||Fully|
|USB Midi 2x2||Midi Controller||USB||M-Audio||Fully functional with up-to-date drivers available from www.m-audio.com website.||Yes|
|Miglia TV||TVMicro USB stick||USB||Miglia||plug and install EyeTV and watch TV||Fully|
|Medion Wireless Keyboard (MD42488||Keyboard||USB||Medion||Powerbutton, Mute, Sound (+/-) and normal keyboard works.||Partially|
|Microsoft Digital Media Pro Keybaord||Keyboard||USB||Microsoft||Full functionally (including zoom switch)with Microsoft OS X keyboard drivers.||Fully|
|EZ-3000||Keyboard||PS2||Vivanco (and EzKEY)||Powerbutton, Mute, Sound (+/-), task-switch and normal keyboard works.||Partially|
|Yakumo Blueport Class 1||Bluetooth Dongle||USB||Yakumo||Apple Keyboard works fine!||Partially tested|
|D-Link DBT-120||Bluetooth Adapter||USB||D-Link||Works w/ iBook, cell phone, no extra drivers needed, automatically detected.||Yes|
|Microsoft Comfort Curve 2000||Keyboard||USB||Microsoft||Everything works, just install software from http://www.microsoft.com/downloads/details.aspx?FamilyID=84bdf38f-efbf-4d31-a0b4-e603a3db5ac8&displaylang=en||Yes|
|Mighty Mouse||mouse||USB||Apple||YaY to side scrolling||all works... why wouldn't it?|
|Btoes Bluetooth USB Adapter||Bluetooth USB Adapter||USB||MSI||Fully functional, except bluetooth headset. Maybe it is not a osx problem||No||Hama Bluetooth USB Adapter||Bluetooth USB Adapter||USB||HAMA||Fully functional, except bluetooth headset.||No|
|HP Deskjet 3940||Printer||USB||Hewlett-Packard||Fully functional with new Universal drivers available from HP's website. -->ALL RECENT HP PRINTERS NOW HAVE UB DRIVERS<--||No|