Editing HCL 10.4.9

This is a component level hardware compatibility list. We want to keep it as accurate as possible, but please, do not entirely rely on this list when buying hardware. Add which parts you have working in the categories listed below, or create a new category. Please keep alphabetical order inside the categories. The categories themselves are ordered by popularity. Please list any caveats or problems as well.

* ONLY add hardware that you have TESTED. Don't add hardware just because you think it might work. 
* Please add hardware into tables. 
* This is for 10.4.9 builds only.

==Motherboards==

A comprehensive list of possible [http://www.intel.com/support/chipsets/ Intel chipsets]

'''PLEASE INCLUDE THE SOUTH BRIDGE TOO'''
===AMD===
----
====Abit====
{| class="wikitable" width="100%"
|-
|[http://www2.abit.com.tw/page/de/motherboard/motherboard_detail.php?pMODEL_NAME=NF-M2+nView&fMTYPE=Socket+AM2 NF-M2 nView]
|Nvidia nForce 4300
|
*Onboard Ethernet (Realtek RTL8111B) - Does not work
*Onboard Sound (Realtek ALC883) - Works
*Onboard GeForce 6150 - Does not work (only VESA, not Natit or Titan)
*SATA - Not tested 
*PATA - Works
|Yes, Uphuck 1.2 and 1.3 with sound driver
|-
|[http://www.abit.com.tw/page/en/motherboard/motherboard_detail.php?pMODEL_NAME=LG-95&fMTYPE=LGA775&pPRODINFO=Specifications&fSEARCHTEXT=LG-95 LG-95]
|Intel 945GC + ICH7
|
* BIOS version: 14 
* Installation method: uphuck 10.4.9
* Audio (ALC 883): 2ch only so far. Works with Azalia driver from installer.
* Video (GMA 950): Not tested, used with Geforce 7600GS
* IDE and SATA: Works out of the box
* ACPI: Restart & Shutdown works fine so far.
* PROs: Very cheap and compatible.
* CONs: NOT an overclocker motherboard, FSB is locked in the Bios.
|Yes, uphuck
||-



|} . .

====As-Rock====
{| class="wikitable" width="100%"
!Hardware Name (socket type)
!Chipset
!Notes
!Fully working without patching
|-
|ASROCK Conroe 1333-D667 (socket 775)
|945G/ICH7
|2.33GHz Core2Duo
Installed JAS 10.4.6, then upgraded to 10.4.10 with Mac.Nub
I've Been running this system rock solid at least 6 months with no glitches!
Also, I understand that upgrading the BIOS past v1.3 will make it not work.  Anyone had any luck with the newest BIOS v1.6?  I want to get a wolfdale chip which isn't supported prior to BIOS rev 1.6.
Also, I'm using a PNY 7300GT 256MB working full QE/CI/OpenGL with mac.nub's 256MB inject driver on the 10.4.10 disc.
|*No.  But everything works if you apply Mac.nub's GMA950 and R1000 drivers from the 10.4.10 disc during install, so YES, sort-of.
Am booting with an IDE drive.  Haven't gotten SATA working native bootable, but it sees all drives attached.
|} . . .

====Asus====
{| class="wikitable" width="100%"
!Hardware Name (socket type)
!Chipset
!Notes
!Fully working without patching
|-
|A8N SLI Deluxe socket 939
|NForce 4
|Installed 
*from Uphuck 10.4.9 v1.3 upgraded to 10.4.10
*Dethforce
*sound, network (with patch) work
*I haven't tried the sata much as I heard there were errors
*Win XP is on sata drive, Mac is on pata
|no
|-


|} . . . . . . . . . . . . .

====DFI====
{| class="wikitable" width="100%"
!Hardware Name (socket type)
!Chipset
!Notes
!Fully working without patching
|-
|Place holder
|Place holder
|Place holder
*Place holder
|Place holder
|}

====ECS====
{| class="wikitable" width="100%"
!Hardware Name (socket type)
!Chipset
!Notes
!Fully working without patching
|-
|P4M800PRO-M
|VIA P4M800Pro & VT8237R+
|Install JAS 10.4.8 with semthex...then used these instructions to update to 10.4.9 http://forum.insanelymac.com/index.php?showtopic=45283&hl
*Place holder
|Place holder
|} . . . .

====Foxconn====
{| class="wikitable" width="100%"
!Hardware Name (socket type)
!Chipset
!Notes
!Fully working without patching
|-
|Place holder
|Place holder
|Place holder
*Place holder
|Place holder
|}

====Gigabyte====
{| class="wikitable" width="100%"
!Hardware Name (socket type)
!Chipset
!Notes
!Fully working without patching
|-
|8I865GME Rev 2.0 
|Everything working fine. usb 2.0 sata II, lan, audio, firewire, video only 1024*764. restart problem solved. little slow than jas  10.4.7. DVD player not working.
|uphuck 10.4.9 
|
|}

====MSI====
{| class="wikitable" width="100%"
!Hardware Name (socket type)
!Chipset
!Notes
!Fully working without patching
|-
|MSI 915PL Neo-V LGA775
|Intel 915PL + ICH6
|Everything seems to be working smoothly except for the following:
*System Preferences show that I have audio input from my headphone but Skype isn't working properly(cannot hear contact speaking, nor can the other side)
*When dual-booting with XP, Ethernet doesn't work after a Reboot in XP; instead of Reboot, a full shutdown (power off) is required to solve this problem
|Yes
|}

====PC Chips====
{| class="wikitable" width="100%"
!Hardware Name (socket type)
!Chipset
!Notes
!Fully working without patching
|-
|Place holder
|Place holder
|Place holder
*Place holder
|Place holder
|}

===Intel===
----
====Abit====
{| class="wikitable" width="100%"
!Hardware Name (socket type)
!Chipset
!Notes
!Fully working without patching
|-
|Place holder
|Place holder
|Place holder
*Place holder
|Place holder
|}

====Albatron====
{| class="wikitable" width="100%"
!Hardware Name (socket type)
!Chipset
!Notes
!Fully working without patching
|-
|Place holder
|Place holder
|Place holder
*Place holder
|Place holder
|}

====AsRock====
{| class="wikitable" width="100%"
!Hardware Name (socket type)
!Chipset
!Notes
!Fully working without patching
|-
|Place holder
|Place holder
|Place holder
*Place holder
|Place holder
|}

====Asus====
{| class="wikitable" width="100%"
!Hardware Name (socket type)
!Chipset
!Notes
!Fully working without patching
|-
|P4B533-V
|Intel 845E / ICH4
|Everything seems to work smoothly, SATA, except audio (uphuck 10.4.9 v1.4i R3 with SATA support).
|Yes
|-
|[[P4P800 VM]]
[http://www.asus.com/products.aspx?l1=3&l2=12&l3=33&model=184&modelmenu=1 ASUS Page]
|Intel 865G GMCH / ICH5
|Everything seems to work smoothly, SATA, network and USB. Audio works stereo, but output jack is mic in by default!
* To fix that (to change it back to the line out) you must modify the file '/System/Library/Extensions/AppleAC97Audio.kext/Contents/PlugIns/AppleAC97CodecAD198x.kext/Contents/Info.plist'
# Find the line with <string>ADS75 ADS74 ADS73 ADS72</string>
# Change it with <string>ADS75 ADS74 ADS73 ADS72 ADS70</string>
# The next step is to load the AppleAC97CodecAD198x.kext
|Yes
|-
|[[P4P800]]
|Intel P4 2.8GHz HT
|Not work (kernel panic with Uphuck 1.3 with Intel SSE2 kernel)
|-
|P4P800 Deluxe
|Intel P4 3.0GHz HT
|Everything seems to work
|Yes
|-
|P4P800S
|Intel P4 3.0GHz HT
|Everything seems to work. Used Uphuck 1.3 with Intel SSE2 kernel.
|Yes
|-
|P5GD2-X
|Intel 915P, P4 3.0 core solo 65nm
|Everything works including QE\CI with callisto 0.08 & coverg patch on DELL 2407WFP (VGA), execept system volume control, and DVI out on video card. My hardware: Saphire ATI x800 GTO 256 pci-x (flashed to x800 GT new id: 0x554b old id 0x554f ). Sound work with sudo kextload /System/Library/Extensions/AppleAC97Audio.kext/Contents/PlugIns/AppleAzaliaAudio.kext/Contents/PlugIns/AppleAzaliaController.kext/
|Yes
|-
|P5LD2-VM
|Intel 945G, Celeron D 347 3.06 
|Core Image & Quartz Extreme Supported With Integrated GMA950 Display, SATA Ports & IDE Ports Work. Onboard LAN works, although Network Control Panel claims the cable is disconnected. (JAS 10.4.8 DVD Updated to 10.4.9) Audio does not work out of the box. Required HDA Patcher. Sleep does not work. System reboots and Powers down with no issues.
|No
|} . . . .

====Biostar====
{| class="wikitable" width="100%"
!Hardware Name (socket type)
!Chipset
!Notes
!Fully working without patching
|-
|Place holder
|Place holder
|Place holder
*Place holder
|Place holder
|}

====ECS====
{| class="wikitable" width="100%"
!Hardware Name (socket type)
!Chipset
!Notes
!Fully working without patching
|-
|Place holder
|Place holder
|Place holder
*Place holder
|Place holder
|}

====Epox====
{| class="wikitable" width="100%"
!Hardware Name (socket type)
!Chipset
!Notes
!Fully working without patching
|-
|Place holder
|Place holder
|Place holder
*Place holder
|Place holder
|}

====FOXCONN====
{| class="wikitable" width="100%"
!Hardware Name (socket type)
!Chipset
!Notes
!Fully working without patching
|-
|Foxconn 45CMX Socket 775
|Intel 945GC
|Working
*SATA
*USB
*PS2
*Grafics
*Lan Needs Drivers [[http://forum.insanelymac.com/index.php?showtopic=84016 look here]] and kext patching [[http://forum.insanelymac.com/index.php?showtopic=29436 look here]]
|No
|} . . .

====Gigabyte====
{| class="wikitable" width="100%"
!Hardware Name (socket type)
!Chipset
!Notes
!Fully working without patching
|-
|GA-945GCM-S2C 
|945GC
|Everything works great using the correct install settings on the uphuck installer.  LAN, Audio, GMA950 graphics all work.  I used the uphuck 10.4.9 v1.4i R3 release.
|Yes, with the right installer settings.
|}

====Intel====
{| class="wikitable" width="100%"
!Hardware Name (socket type)
!Chipset
!Notes
!Fully working without patching
|-
|D945GNTL
|Intel® 945G Express Chipset
|Works: LAN (Intel Pro 10/100, IONetworkingFamily 10.4.7), USB, Audio (SigmaTel 9220, Blue = out, green  = in, pink = Mic), SATA and ATA
|JaS 10.4.8 DVD SSE3 + JaS 10.4.9 Combo Update
|-
|D945GTPLKR
|Intel 945G Express Chipset, Intel GMA950 Graphic Chipset
|Everything works fine exept: 1) LAN works without fuzz when in Bios "boot to Network" is enabled 2) Sigmatel 9220 with no "line in" function (blue = line out, green = nothing, red = Mic); All Apple Security Updates and Application Updates till 2007-06-11 can be directly applied without further ados
|10.4.9 uphuck install dvd 1.2 with: Intel SSE3 Kernel, IOATAFamily Patch, ICH7-R Driver, Azalia Audio Driver
|-
|D975XBX Rev 3.02
|Intel® 975X/ ICH7R
|Works: LAN, USB, FireWire, Audio is working by switching to the blue pin instead of the green 1 (with the SigmaTel 9221 AppleHDA Patch), SATA and ATA133 (with the Jas 10.4.8 patched ppf1 dvd), Raid not tested.
|JaS 10.4.8 DVD With PPF1 Patch and JaS 10.4.9 Combo Update
|}

====Iwill====
{| class="wikitable" width="100%"
!Hardware Name (socket type)
!Chipset
!Notes
!Fully working without patching
|-
|Place holder
|Place holder
|Place holder
*Place holder
|Place holder
|}

====MSI====
{| class="wikitable" width="100%"
!Hardware Name (socket type)
!Chipset
!Notes
!Fully working without patching
|-
|Place holder
|Place holder
|Place holder
*Place holder
|Place holder
|}

====PC Chips====
{| class="wikitable" width="100%"
!Hardware Name (socket type)
!Chipset
!Notes
!Fully working without patching
|-
|Place holder
|Place holder
|Place holder
*Place holder
|Place holder
|}

====Tyan====
{| class="wikitable" width="100%"
!Hardware Name (socket type)
!Chipset
!Notes
!Fully working without patching
|-
|Place holder
|Place holder
|Place holder
*Place holder
|Place holder
|} .

==Processors==
===AMD===
{| class="wikitable" width="100%"
! Model
! Notes
! Recognized as
! Full Work / No Patch
|-
|Place Holder
|Place Holder
|Place Holder
|Place Holder
|}

===Intel===
{| class="wikitable" width="100%"
! Model
! Notes
! Recognized as
! Full Work / No Patch
|-
|Intel Core 2 Duo E4500 Allendale 2.2GHz
|uphuck 10.4.9 v1.4i R3 installer used
|Recognized as 2.21ghz Core2Duo
|Yes
|-
|Intel® Core™2 Duo E6600 (2.4 GHz)
|JaS 10.4.8 SSE2/SSE3 + ppf1 and JaS 10.4.9 Combo Update, kernel Semthex 8.9.1 - Both cores working, 100% trouble-free
|Recognized as a dual core 2.4 Ghz Cpu
|Yes
|-
|Celeron D 325
|Used JaS 10.4.8 SSE2 SSE3 reseed w/Semtex 8.8.1 + JaS 10.4.9 SSE3 patch w/Semtex 8.9.1, it didn't worked well right away (choppy sound and slower GUI) but I set the com.apple.info.plist "<key> Kernel Flags </key>" entry with "<string>fsb=133</string>" and everything went smoothly!
|Intel Core Solo 2.53 Ghz (right speed)
|Yes / See Notes
|-
|Intel® Pentium D 940+ (3.2Ghz)
|JaS 10.4.8 SSE3 + JaS 10.4.9 Combo Update, kernel Semthex 8.9.1 - cores working
|Recognized as a 4Ghz Intel Core Duo
|Yes
|-
|Intel® Pentium 4 (2.53Ghz and No SSE3)
|uphuck 10.4.9 v1.4i R3
|Intel Pentium 4 2.53 Ghz
|Yes
|-
|Intel® Pentium 4 (1.8Ghz and No SSE3)
|JaS 10.4.8 SSE2 SSE3 AMD kernel 8.8.1, updated to 10.4.9 with 8.9.1 kernel
|Intel Core Solo 1.79Ghz (right speed)
|Yes
|-
|Intel® Pentium 4 530J (3.00 GHz, SSE2 and SSE3)
|JaS 10.4.8 SSE3 and JaS 10.4.9 Combo Update, kernel 8.9.1, 100% trouble-free
|2.99GHz Intel Pentium 4
|Yes
|} . .

==Graphics Cards== 
Please specify if your card is AGP, PCI or PCI-E.<br />
Also, place chip and board manufacturer in their respective column.

<div style="border: 1pt dashed blue; background : grey; padding: 1em 1em;">
'''Note''': For NVidia users, visit http://www.macvidia.org/ for updated drivers. For NVIDIA CARDS PLEASE SPECIFY IF THE CARD DOES QE/CI. Saying the macvidia drivers work but not specifying QE or CI is a bit misleading. 
If you are using the new kernel then download the Titan kext from http://omni.starchaser.org/titan/ to get QE/CI support

'''Note''':These instructions may confuse noobs as they are a bit out of date. As far as i know, the MacVidia drivers do NOT support QE/CI AT ALL. You can use the kexts that come with your OSx86, or the ones from the 10.4.8 Intel update with your card. You may need to replace OpenGL.Framework too. Titan and Natit are merely enablers which make OSx86 think your VGA BIOS card is an EFI Firmware one (as on a real intel mac), and should load before the NVNVDA* kexts. An installer for Natit can be found at [http://installers.dl.am/]. Check the forums for more info.
</div>

<div style="border: 1pt dashed blue; background : grey; padding: 1em 1em;">
'''Note''': For ATI users, visit http://omni.starchaser.org/ for experimental drivers.
</div>

<div style="border: 1pt dashed blue; background : grey; padding: 1em 1em;">
'''Note''': As of right now, all ATI cards with working kexts have severe slowdown issues with nForce3 chipsets. There is no fix for this, save getting editting out your card from the kext or using Quartz Debug to shut off Quartz Extreme. Edit: Just use agpgart to get no slowdowns at all on nForce3. Joblo10
</div>

===PCI Express===
----
====ATi====
{| class="wikitable" width="100%"
|-
!Hardware Name,(VRAM)
!Board-Manufacturer
!Notes                
!QE / CI
!Resolution
!Full Work / No Patch
|-
|Place Holder
|Place Holder		
|Place Holder
#Place Holder
|Place Holder
|Place Holder
|Place Holder
|}

====Intel====

{| class="wikitable" width="100%"
|-
!Hardware Name,(VRAM)
!Board-Manufacturer
!Notes                
!QE / CI
!Resolution
!Full Work / No Patch
|-
|Intel 82945G 8mb
|Intel		
|Use native drivers
|none
|1024*768
|without quartz extrime
|} . . . .

====Matrox====
{| class="wikitable" width="100%"
|-
!Hardware Name,(VRAM)
!Board-Manufacturer
!Notes                
!QE / CI
!Resolution
!Full Work / No Patch
|-
|Place Holder
|Place Holder		
|Place Holder
#Place Holder
|Place Holder
|Place Holder
|Place Holder
|}

====NVidia====

{| class="wikitable" width="100%"
|-
!Hardware Name,(VRAM)
!Board-Manufacturer
!Notes                
!QE / CI
!Resolution
!Full Work / No Patch
|-
|Geforce 7800GTX 256MB
|ASUS		
|Used the Natit 1.0 Installer from http://www.necnet.de/krass.man/Installers/NVidia%20(Natit)%20Installer.html
|Both
|ALL
|Yes/Requires NV40 thing or the Natit 1.0 or higher Installer
|-
|Geforce 6600XL 128MB
|Foxconn		
|Worked rightaway
|Yes/Yes
|HiDefinition
|Yes
|-
|Geforce 6500 256MB
|XFX		
|Used the Natit 1.0, works as 128MB
|Yes/Yes
|HiDefinition
|Yes/Natit 1.0 or higher
|} . .

===AGP===
----
====ATi====
{| class="wikitable" width="100%"
|-
!Hardware Name,(VRAM)
!Board-Manufacturer
!Notes                
!QE / CI
!Resolution
!Full Work / No Patch
|-
|Radeon X1600 Pro (256MB)
|Sapphire
|Works out of the box on an ASUS P4P800-VM MB
|Yes plus Q2D capable (gives a great speed boost on iWork '06 Pages program)
|Any
|Yes
|-
|Radeon X1950 Pro (512MB)
|Sapphire
|Works on a Gigabyte 8IPE100 MK MB with fresh install and Bronya's (Dmitrik) drivers for Prionace
|Yes
|Any
|Yes
|} . . .

====NVidia====
{| class="wikitable" width="100%"
|-
!Hardware Name,(VRAM)
!Board-Manufacturer
!Notes                
!QE / CI
!Resolution
!Full Work / No Patch
|-
|Geforce 6200 (128MB)
|XFX		
|Works perfectly after installing Titan, no kexts editing required
|Yes
|Any
|Yes/No
|-
|Geforce 7300GT (256MB)
|PNY		
|Works perfectly after installing mac.nub's 256MB inject on the 10.4.10 disc
|Yes and OpenGL
|Any
|Yes/No
|} . .

===PCI===
----
{| class="wikitable" width="100%"
|-
!Hardware Name,(VRAM)
!Chip-Manufacturer
!Board-Manufacturer
!Notes                
!QE / CI
!Resolution
!Full Work / No Patch
|-
|Place Holder
|Place Holder		
|Place Holder		
|Place Holder
#Place Holder
|Place Holder
|Place Holder
|Place Holder
|}

===Mobile===
----
{| class="wikitable" width="100%"
|-
!Hardware Name (VRAM)
!Chip-Manufacturer/Board-Manufacturer
!Notes                
!QE / CI
!Resolution
!Full Work / No Patch
|-
|Mobile 945GM Express Integrated Graphics Controller (rev 03)
|Intel		
|Works Natively
|Yes
|1280x1024
|Yes - Fully works with Intel GMA950 Driver
|} . . . . . . . . . . . . .

== Sound Cards ==
{| class="wikitable" width="100%"
|-
!Hardware Name
!Manufacturer
!Notes
!Fully working without patching
|-
|AC97  6-channel audio codec S/PDIF out interface(ADI 1980)
|Realtek
|Must patch to get the sound on line out instead of mic in:
* Edit the /System/Library/Extensions/AppleAC97Audio.kext/Contents/PlugIns/AppleAC97CodecAD198x.kext/Contents/info.plist
# Find the line with <string>ADS75 ADS74 ADS73 ADS72</string>
# Change it with <string>ADS75 ADS74 ADS73 ADS72 ADS71 ADS70</string>
# The next step is to load the AppleAC97CodecAD198x.kext
|See notes
|}

{| class="wikitable" width="100%"
|-
!Hardware Name
!Manufacturer
!Notes
!Fully working without patching
|-
|USB 2.0 Soundkarte Virtual 5.1 Exterior Audio Adapter
|Exterior Hong Kong (eBay)
|Works without patching, line out and line in
* Deaktivate your internal audio, then plug the USB Audio Adapter in your USB 2.0 Port
|YES!!! OSX 10.4.9 and 10.4.10 - Super Stereo Sound!
|}

==Network Cards==
===Wired (Ethernet)===
{| class="wikitable" width="100%"
|-
!Hardware Name
!Manufacturer
!Notes
!Fully working without patching
|-
|DFE-538TX, Device ID 0x1300
|D-Link, Vendor ID 0x1186
|Works without problems out of the box!
|Yes
|-
|Realtek811B, Device ID 0x8136
|Realtek, Vendor ID 0x10EC
|Needs Drivers [[http://forum.insanelymac.com/index.php?showtopic=84016 look here]] and kext patching [[http://forum.insanelymac.com/index.php?showtopic=29436 look here]]
|No
|-} .

===Wireless===
{| class="wikitable" width="100%"
|-
!Interface
!Standard
!Device
!Manufacturer
!Notes
!Fully working without patching
|-
|PCI
|B/G
|WG311T
|Netgear
|Reconized as Airport right out of the box (What version is it?). Speeds up to 108mb/s. If not recognized try using [[http://forum.insanelymac.com/index.php?showtopic=33089&st=0&p=238508&#entry238508 this method]]. 
|Yes
|-
|Mini-PCI Card
|802.11 b/g
|1390 WLAN (rev 01)
|Broadcom Corporation/Dell
|uphuck v2 detects this as "Built-in Ethernet" in Network Preferences. No Airport card was shown in Network Preferences even though wireless worked properly. It didn't show the signal strength but webpages were working with no ethernet cable plugged in. This was fixed in v1.3 and v1.4i and the wireless card was displayed properly as "AirPort".
|YES, only with uphuck 10.4.9 v1.3 and newer. v1.2 has issues.
|} . . . . . .

==Other Expansion Hardware==
{| class="wikitable" width="100%"
!Hardware Name
!Interface
!Device
!Manufacturer
!Notes
!Fully working without patching
|-
|Wireless Traveler SE2 
|USB
|Mouse Optical
|Genius
|100% works
|Yes/Genius Driver
|} . . . . . .