HCL 10.5.1/Portables

From OSx86
Revision as of 01:08, 5 April 2008 by Dparada78 (Talk | contribs)

Jump to: navigation, search


This is a hardware compatibility list for 10.5.1 builds. Don't forget to add how you got OSx86 running on your portable x86 computer, and to use proper English. Please see the discussion page for proper instructions on how to input your system specs. Also, please contribute to the HCL 10.5.1 page, which should list a more granular view of compatibility. If your computer isn't listed, you should try it if you have a SSE2 or higher processor. Kernels are available for most configured machines.

See the x86 software page for programs you can run without Rosetta.

Please list your computers in alphabetical order by manufacturer (Asus, Acer, Dell, HP, etc)



Acer Aspire 4320

  • Install Method:
  • Chipset: Intel 965
  • Processor: Intel Celeron 1.73 GHz
  • Audio works with AppleHDA patcher
  • LAN doesn't work
  • Bluetooth works

Acer Aspire 5024

  • Install Method: Zephyroth for AMD
  • Processor: Turion 1.8Ghz 64bit ML34
  • To install:
    1. Installation hangup at the end, you need to manually install bootloader:
      • Reboot with dvd and switch "-s" than install i386 boot loader to the OSX partition, this can be done with DD command like this example: "if=/usr/standalone/i386/boot1h of=/dev/rdiskXsY bs=512 count=1" this may destroy all data on your hd please take care!!
    2. After reboot you need to manually install a few Extensions (I've used from my older 10.4.8)
      • ApplePS2* <- to use touchpad and keyboard
      • Callisto* <- to enable 1280x800 LCD switch resolution (patched for 1280x800 LCD DOTCLOCK!!!)
      • ATIRadeon9700.kext <- from 10.4.8 because newest does not work (already patched to support 0x5653)
      • ATIRadeon9700GA.plugin <- from 10.4.8 because newest does not work (already patched to write to CallistoFB) .

Acer Aspire 5050

  • Install Method: Zephyroth
  • Processor: Turion 64 2.0GHz
  • Installation hangs, use same method as above
  • SATA does not work, using USB HDD
  • Audio does not work yet, Azalia might do the trick
  • needs PS2 kext
  • WIFI works out of box

Acer Aspire 5051AWXMi

  • Install Method: Zephyroth
  • Processor: AMD Turion 64 Mobile MK36 (2GHz)
  • Audio works with Azalia
  • LAN works out of the box
  • ATI Radeon XPRESS x1100 works with edited Callisto (No QE)
  • WIFI works out of box
  • PCMCIA works
  • Camera & Card Reader don't work
  • Install Guide here .

Acer Aspire 5570Z

  • Install Method : iATKOS 1.0 r2 MBR + EFI, patched kernel, speedstep
  • Processor: Intel Pentium Dual-Core T2060 @ 1.60GHz, speedstep working.
  • Audio: ALC883: Azalia audio patch on iATKOS gives internal speakers only. AppleHDA gives headphones and line-in, but no internal
  • Video: GMA950 works out-of-box, but with mouse tearing in Firefox
  • PCI: install chun-nan's patch [1]
  • WLAN: Original Atheros AR5007EG not tested, traded for Giga-byte GN-WI01T (works after PCI patch)
  • LAN: Marvell 88E8038: patch AppleYukon2.kext inside IONetworkingFamily.kext [2] (do this before PCI patch, otherwise wireless will be en0 and wired will be en2)
  • PCMCIA: works after chun-nan patch .

Acer Aspire 5572WXMi

  • Install Method: Kalyway 10.5.1 clean MBR install w/ flag "-v cpus=1" all the time.
  • Post Install Problem: looping on "Do you already own a mac?" see: http://osx86.wikidot.com/known-issues#toc9
  • Processor: Intel Core Duo @1.66x1
  • Audio works w/ Azalia
  • LAN works w/ the patched IOPCIFAMILY.KEXT(test.only7 IOPCIFamily) and edited YUKON2.KEXT in IONETWORKING.KEXT.
  • Reading for Lan: http://forum.insanelymac.com/index.php?showtopic=87592
  • GeForce GO 7300 128M QE/CI works w/ NVinjectGO
  • Wireless Intel 3945G does not work.
  • Asus WL-167G USB wireless adapter working fine with Ralink RT2870 driver
  • PCMCIA works w/ the above patched IOPCIFAMILY.KEXT
  • Camera detected, but not working
  • Buletooth works out of box . . .

Acer Aspire 5610z-2966

  • Audio works after installing AzaliaAudio
  • Wireless working out of the box
  • GMA950 works fully with Natit drivers
  • EFI v.8 confirmed working on GUID Partition Table . . .

Aspire 5612WLMi

  • Install Method: Kalyway
  • Processor: Intel Core Duo T2300 @ 1.66GHz
  • Audio & Broadcom 440 (LAN) working
  • nVidia GO7300 works with NVinject. Dual screen doesn't work. QE/CI & All resoltuions
  • Intel 3945 (Wireless) doesn't work
  • Card Reader doesn't work
  • Webcam doesn't work

Aspire 5920g

  • Install Method: Kalyway 10.5.1 w/ EFI
  • Processor: Core 2 Duo T5450 @ 1.66GHz
  • Audio works with Azalia
  • LAN BCM5787M doesn't work
  • nVidia 8600M GS works with this driver
  • Flash Card reader doesn't work
  • Webcam only shows green
  • SATA HD works . . . . . . . .

Extensa 5620z

  • Install Method: Iatkos v1.0i (do not forget to update the BIOS before you start!!!)
  • Processor: Core 2 Duo T2310 @ 1.46GHz
  • Audio works but (no mic & headphone) you can try the (ALC 268) driver
  • LAN doesn't work but Wlan works
  • VGA Intel GMA 31oo works
  • Flash Card reader doesn't work
  • How to install:
                                   + Iatkos main system
                 Additional patch: + Efi emulation + Stock kernel
                                                     (Do not install stock apple acpi platform kext!!!)
                                   + remove cpu power management
                                   + remove kernel text 
                           Driver: + Intel GMA x3100
                           System: + Apple smbios.kext Netkas . . .


Asus U3S

  • Install Method : iAtkos 10.5.1, bootloader from zephyroth 10.5.2, bluetooth drivers from kalyway 10.5.1
  • Processor : Core 2 Duo T7500 @ 2,2GHz. Both core enabled.
  • Sound works
  • nVidia 8400m works with driver from DiaboliK ( natit ). Intel GMA X3100 works with Apple Graphics Update.
  • Wifi doesn't work, ethernet works OOB.
  • Powermanagement works, with powermanagement.bundle for leopard
  • Check [3] for a full guide on how to install leopard on the U3S.

Asus G1-AK024C

(This is for the original with the T7200 and GeForceGo7700)

  • Install Method : Kalyway 10.5.1. Installed it on USB hard drive, works perfecly (Use NVinject's 0.2.0 512Mb version or later, if you use those from Kalyway you'll have to start in -x (Safe mode) to install them)
  • Processor : Core 2 Duo T7200 @ 2GHz. Both core enabled.
  • No sound from the original installation, will have to try with Kalyway's and third-party's drivers.
  • nVidia GeForce Go 7700, normally have 512Mb + 700-some Mb shared for memory, Darwin sees 256. Otherwise, it looks like it's fully working, except for weird lines and color changes after the Apple logo (dont know if the color change is normal in Leopard, but the lines aren't). As indicated in Install Method, use NVinject's 0.2.0 512Mb or later.
  • Since it's basically the same laptop as the G1S, I won't list the other components because they are all the same things. Only tried WiFi (doesn't work).
  • Power management doesn't work either, no battery meter but sleep does work. Takes a long time to reboot or shutdown, may be caused by the USB connection.

Asus G1S-A1

  • Install Method: Kalyway 10.5.1 (no acpi) w/ EFI. remove old ACPI kext's and replace them with kext's from 10.4.8. Also, remove all Firewire kext's. Eventually you should be able to boot with either cpus=1 or cpus=1 -f. No Safe Mode!
  • Processor: Core 2 Duo T7200 @ 2.2GHz. Only one core though (cpus=1 at boot).
  • ALC660 built-in sound works, microphone doesn't, don't know about SPDIF.
  • LAN works natively.
  • Wireless doesn't have a driver yet. People are cracking away at the Intel 4965.
  • nVidia 8600M GT works with nvinject 0.2.0 fix (QE/CI, all compatible resolutions enabled)
  • Flash Card reader doesn't work natively, haven't tried finding drivers. (brand: RICOH afaik)
  • DVD Burning works natively.
  • Bluetooth works natively.
  • Webcam works sometimes, sometimes it doesn't. besides iChat I haven't tried 3rd-party applications.
  • SATA built-in HD works, eSATA doesn't.
  • HDMI works natively full HD resolution - 1920x1080. Tried it with my 42" Sharp Aquos LCD.
  • No powermanagement natively (No battery meter, no sleep). I haven't tweaked it yet though, it may be possible.

Did I leave anything out? Stuck? Any Questions? PM me at the insanelymac forums id:soupcancooloff . .

Asus F3JM

  • Install Method: Kalyway 10.5.1 with EFI
  • CPU: Intel Core 2 Duo T5600 @ 1.83 GHz. Both cores work
  • VGA: NVIDIA Geforce 7600 Go 512MB works with nvinject go 0.2.0 (QE/CI enabled)
  • LAN: Realtek RTL8168 works with R1000-Driver
  • WLAN: Intel 3945 doesn't work
  • Sound: Realtek ALC861 works with patched AppleHDA
  • Bluetooth: works ootb .

Asus A8Fm

  • Install Method: iATKOS v1.0ir2, 10.5.1 with EFI
  • CPU: Intel Core 2 Duo T5500 @ 1.66 GHz.
  • VGA: Intel GMA 950
  • LAN: Realtek
  • Sound: HD built in sound

Sound, LAN working, WLAN yet to test Skype crash upon call establish

Asus Z71A

  • Install Method: Kalyway 10.5.1 with EFI
  • CPU: Intel Pentium M (Dothan) 2.0GHz (shown as "unknown 2.0GHz")
  • VGA: NVIDIA GeForce 7600 Go 128MB. CI/QE working.
  • Lan: Marvel/Yukon chip. Using m.musashi's driver(v 0.2e)
  • WiFi: Intel 2915ABG, Not working. Using Javaoui's driver causes system reboots
  • Sound: Azalia HD. Not working yet, Still fiddling with drivers.

Nothing else is tested. I will update if I get sound working.

Asus Z71V

  • Install Method: Kalyway 10.5.1 with EFI
  • CPU: Intel Pentium M (Dothan) 1.73 GHz (shown as "unknown 1.73 GHz")
  • VGA: NVIDIA GeForce 6600 Go 128MB. CI/QE working.
  • Lan: Marvel/Yukon chip. Using skge.kext
  • WiFi: Intel 2915ABG, Working. Must do manual install using kext helper.
  • Sound: Azalia Out. Working

iCal, DVDplayer.app not working. Still figuring out problems. Tried 10.5.2 update as well. Workable, however same problems and longer boot than 10.5.1.

Asus V1S (V1S-AK012E)

  • Install Method: Kalyway 10.5.1 with EFI
  • Processor: Core 2 Duo T7500 @ 2.2GHz. Only one core (cpus=1 at boot).
  • VGA: nVidia GeForce 8600 GT (NVInstallerV.33)
  • Lan: Intel Corporation 82566MM Gigabit - Not working yet
  • Sound: Realtek ALC660-VD - Not working yet
  • Wifi: Intel Corporation PRO/Wireless 4965 AG - Not working yet

Other components not yet tested... Note : I'm still booting using the DVD (rd=diskXsY cpus=1) and the system freezes after a few minutes inactivity . . . . . . . . . .


Benq A52-V03

  • Install Method: Kalyway 10.5.1 with EFI. Default kernel (not vanilla), no video card drivers selected.
  • Processor: Core 2 Duo T2080 @ 1.73GHz.
  • VGA: Radeon Xpress 200M. Correct 1280x800 resolution achieved with Katana installer, version 2c.
  • Lan: Realtek RTL-8139. Working.
  • Sound: Realtek ALC262. Only speakers working (no headphones or mic), with Azalia. No success with Applehdapatcher and various versions of ALC262 codec.
  • Wifi: Atheros AR5006EG - Not working.
  • Powermanagement: Battery monitor working with PowerManagement_137_1.bundle, although not until change from battery to plugged-in state. /System/Library/Extensions/AppleACPIPlatform.kext/Contents/Plugins/AppleACPIPowerSource.kext/Contents/Info.plist also edited to reflect correct AppleACPIPlatform version number. Further testing required.

Note: The two biggest problems so far are audio and wireless. .

Benq S41-C46 (This model maybe just sell in Mainland China)

  • Install Method: Kalyway 10.5.1 with EFI. both vanilla, no video card drivers selected.
  • Intall the KalywayIntelCombo10.5.2.pkg and kalyway_10.5.2_kernels.mpkg update the system to 10.5.2.
  • Install Restore_Factory_Desktop_settings to restore icons and desktop.
  • Processor: Core 2 Duo T7250 @ 2.00GHz. OSX identify it as 1.99GHz
  • VGA: nVidia 8600m GS. Correct 1280x800 resolution achieved with NVinject.41 installer, QE/CI all supported.
  • Sound: Realtek ALC262. Only speakers working (no headphones or mic), with Azalia in Kalyway OSX 10.5.1 leopard installation DVD.
  • LAN: Yukon 88E8055 work with the PCCard.10.5.2.Beta2.pkg (http://forum.insanelymac.com/index.php?showtopic=81036&st=500)

Add your LAN hardware id into /System/Library/Extensions/IONetworkingFamily.kext/Contents/PlugIns/AppleYukon2.kext/Contents/Info.plist and then install the PCCard pkg

  • Wifi: Atheros AR5006x - Not working. You can think about purchase a TP-Link TL-WN322G+ or D-Link DWL-G122 USB WiFi Dongle for the wifi solution.
  • Powermanagement: Battery monitor working with PowerManagement_137_1.bundle, although not until change from battery to plugged-in state.

Note: The biggest problems so far are audio input and output... . .


Acteon ACT-N707

  • Install Method: iATKOS 1.0i with included EFI bootloader. Computer heats a lot (as any other Intel computer) if you don't remove AppleIntelCPUPowerManagement.kext and AppleCPUThermo.kext. Boots normally, even with stock kernel. Installation went smoothly. You have to use a Linux LIveCD with GParted to set the HFS+ Partition bootable.
  • Processor: Intel Celeron M 440 @ 1.87GHz.
  • Realtek ALC883 integrated audio works very well, integrated microphone doesn't, however input works. SPDIF LED is lit, output works on both headphones and speakers.
  • Realtek RTL8139C integrated network doesn't work, you need to use Tiger's AppleRTL8139Ethernet or PCGenRTL8139Ethernet. Always remove Leo's AppleRTL8139Ethernet.
  • MSI RT73 wireless works with Prasys' RT73 wireless driver. First copy the LAN entry from the NetworkInterfaces.plist. Reboot with -f -legacy and your Ethernet won't show on System Preferences. Copy the ethernet setup from your old NetworkInterfaces.plist. Change BSD names, etc. and save it. You don't need to reboot for it to take effect. Attention: You need to use the USBWirelessUtility included. Wireless shows as Ethernet.
  • Intel GMA950 works out of the box, TV-Out not tested.
  • Card reader doesn't work, it is connected to the PCI bus. (brand: O2Micro)
  • DVD Burner is suppoted with the "Generic Drive Support".
  • SATA HD works.
  • Battery works, even charger works.
  • Sleep doesn't work, Shutdown causes panic, Restart works.

If you have a problem, PM iNoob at InsanelyMac Forums. .


Presario C500 C571NR

  • Install Method: Kalyway 10.5.1
  • CPU: Pentium IV Dual Core 1.6 ghz
  • Everything works right out of the box (networking, audio, video) but it is somewhat slow on the install (3-4 hours).
  • Using external USB

Presario C700 GF440AV

  • Install Method: iATKOS v1.0i
  • Processor: Celeron M CPU 530 seen as 3.47 GHz
  • Audio works out of box Volume Fn PG UP / PG DN works fully
  • DVD Drive seen as Burn Supported (Generic Drive Support)
  • Video Driver: Intel X3100 works fully using included Intel X3100 driver checked off (1280 x 800)
  • SATA: Intel ICH8-M AHCI works fully
  • USB 2.0: works out of box
  • Ethernet (wired): installed correctly (but not fully tested)
  • Ethernet (wireless): Broadcom B/G not working (button controlled)

  • Installed using iATKOS v1.0i DVD with Darwin Bootloader and efi support. Successful install first try. Wireless doesn't work but my workaround is EnGenius WLAN USB EUB-3701 stick based on RaLink chipset (same as in wii) using RaLink 10.4 Driver (rock solid).
    • Special note: Dual booting with Windows XP using Bootit NG bootloader. Havn't seen this mentioned yet - been using this for years with enormous success - can also resize partitions NON-DESTRUCTIVELY and is much better and easier than any Linux or F-Disk utility!!!

   pressario v 3070 TU
BOTH cpu working , installation method kalyway 10.5.1 with vanilla kernel mbr bootloader efi.Audio works with azalia from uphuck 10.4.9. but no mic or headphone jack works.

intel GMA 950 graphics work with full QE/CI support. LAN works after installing IO802 family kext.and intel driver from uphuck 10.4.9 intel 3495 abg not working. Attempt to install iwidarwin resulted in kernel panic usb 2.0 fully working no battery meter as it is recognised as mac pro sleep works and it wakes after sleep. . .

Presario C500

  • Install Method: Kalyway 10.5.1
  • Processor: Intel T2400 1.83 GHz
  • Audio/vid/dvd work (std Kalyway install options, QE + CI available from first boot)
  • Ethernet is RTL-8139, works from first boot
  • Wireless (BCM 4311) is compatible but PCI bus not recognized; wireless button s/w controlled, have not found a fix yet.
  • Nearly 100% compatible, unfortunately the weak spot is wireless. If OS X could recognize the card in ioreg, this would be near-perfect budget Leopard system.

Presario C712NR

  • Both CPU cores working
  • Intel GMAX3100 fully working with Paulicat's natit.kext for X3100
  • Wireless working out of the box
  • DVD Burner working fully with burning
  • Audio works with AppleAzaliaAudio.kext but no headphones or mic working
  • USB 2.0 fully working
  • Requires ACPIPS2Nub.kext for PS/2 and Power Management
  • Wireless on/off button works but you can't turn it back on with the button (have to turn on AirPort in System Preferences)
  • Volume Up/Down/Mute, Brightness control, and Home keys (PgUp and PgDown too) work on keyboard ; no other special keys working
  • Sleep works but will not wake after sleep
  • Power Management doesn't fully work (sleep sometimes crashes, no battery meter, no SpeedStep)
  • Guide here
  • Basic Method:

Format/unmount target drive -> Run script from "I_am me" with target drives changed-> install brazilmac leopard DVD-> Del: AppleIntelCPUPowerManagement.kext & AppleIntelIntegratedFramebuffer.kext (messes with x3100) & AppleEFIRuntime.kext (can freeze you at spinning apple logo)-> copy dsmos.kext (newest one not from PC-EFI 5.1), & ACPIPS2Nub.kext, Natit.kext over and chmod/chown them all and delete extensions.mkext and finally repair permissions. . . . .

Presario C714NR

iATKOS 1.0 v2, MBR file format, Darwin x86 boot loader, Install went as follows: I checked in drivers Intel x3100, Realtech 8139 NIC, SMIbios, SATA support. Nothing else needed. I used Azalia Audio driver from Uphuck 10.4.9 v1.4 R3. After the install I got the results below.

  • Both CPU cores working
  • Intel GMAX3100 fully working with QE/CI showing 144 megs of shared memory
  • DVD Burner working fully with Toast
  • Audio works
  • USB 2.0 fully working
  • Touchpad works
  • Wired NIC works

Not working- Atheros 5007 Wifi mini PCIe (using Afterthemac USB Dongle from ebay) Everything very stable, running Photoshop CS3 extended, iLife '08, iWork'08, MS office'08 with no problems, no overheating.

UPDATE- installed Kalyway 10.5.2 upgrade with great results and stability, it takes longer to boot after the Kalyway updater, but after install all the other updated from Mac (except any Core updates, the time machine/airport update, and security update) everything is fast and working G.M. . . .

Presario C742EA

  • Both CPU cores working
  • Intel GMAX3100 fully working
  • Wireless working out of the box
  • DVD Burner working fully with burning
  • Audio works
  • USB 2.0 fully working
  • TOUCHPAD works partly
  • Wireless on/off button works but you can't turn it back on with the button (have to turn on AirPort in System Preferences)
  • Volume Up/Down/Mute, Brightness control, and Home keys (PgUp and PgDown too) work on keyboard ; no other special keys working
  • Sleep works but will not wake after sleep
  • Power Management doesn't fully work (sleep sometimes crashes, no battery meter, no SpeedStep) .

Presario C751NR

  • Windows Vista on internal SATA without bootloader
  • Mac OS X 10.5.1 using the iAtkos v.1.0 r2 install DVD (no EFI) on external USB drive with out bootloader
  • Switching between Vista and Mac OS X with boot device setup in BIOS
  • CPU Intel Dual Core T2330 both cores working
  • Display (Intel GMA X3100) working out of the box
  • Sound working out of the box
  • LAN working out of the box
  • Build-in WLAN not working
  • WLAN Dlink WUA 1340 USB working with Dlink supplied driver for 10.4
  • Printer Epson CX4600 USB workink with Epson supplied driver for 10.4
  • Scanner Epson CX4600 USB working out of the box
  • Bluetooth adapter Cambridge Silicon Radio USB working out of the box
  • Bluetooth mouth Logitech V470
  • CD/DVD burning not working (and I didn't do any research yet either)

--matjes 00:28, 18 February 2008 (UTC) . . . . .


Inspiron 1720 =

Install method: iATKOS 10.5.1; Core 2 Duo 2Ghz+2Ghz/3Gb ram/160Gb Hitachi 7200HDD; WLAN, LAN, Bluetooth, USB works put of the box; Video NVidia 8400M worked after installation of NVinject 0.2.1 resolution switchable, 32 bits; Shut down, Restart, Sleep modes doesn't work, Actually shut down partly does, but I have to manually switch off the computer by pressing and holding Power button. Audio - no audio at all (No audio input in system preferences displayed) SigmaTel 9025HD audio. Mouse pad works, mouse tapping not. Keyboard shortcuts partly work. Something wrong with battery counter, cause in Vista it served for over 3h, in OSX though, approx just 2h under 'better energy savings' . Despite above listed issues, overall OSX on my Dell runs like crazy: 700Mb video file was encoded 4 times (!) faster than in previous PowerBook 4-1.67/2Gb/17inch/120Gb... The OSX completely loads in 25 seconds. I was amazed, just hope in the next month to fix audio problem. Hope to install on HP ZT3300 as well, already tried, but can't start installation, some strange message appears, sounds like: 2 modules re using the same ACPI settings... . . . . . . . . A week later: I enforced to function audio as well. Now I can play music, movies, the mic input though doesn't work. .

Inspiron 1525

Inspiron 1520

  • Install Method: Kalyway 10.5.1 DVD, MBR
  • Audio: Sigmatel 9205, patched with AppleHDA 1.16
  • LAN: worked out-of-the-box
  • Video: GeForce 8400M GS, everything working with NVInject
  • Shortcut buttons working
  • No battery monitoring, no wifi (Intel PRO/Wireless 3945abg)

Inspiron e1405

  • Install Method: Kalyway, GUID, EFI v8 patch
  • LAN & WLAN work out of box, though not fully tested
  • Audio with bugs, mute doesn't work, Patched with AppleHDA 1.2

Inspiron 1420

  • Install Method: Uphuck iATKOSr2
  • Audio only one headphone jack works
  • nVidia Geforce 8400 M GS QE/CI working and resolution is changeable .
  • Using a Dell 1505 wireless card that works natively with airport.
  • Everything else is working including the pc card port, webcam, quick access buttons, sd card reader, video out.
  • No s-video out. . .
  • PS:Also ,you can use kalyway leopard 10.5.1.iso but at the same time ,take off your battery :)

Inspiron 5100

  • Spec: 2.53Ghz Northwood SSE2 ONLY!, 1GB RAM, SVGA+ LCD, ATI 7500 32MB, 80GB HD
  • Install Method: iATKOS 10.5.1r3 (patched to BAD BIOS) DVD (MBR)
  • ATI Mobility 7500 works partially (NO QE) with older driver pack.
  • Internal NIC & WLAN Works (use older kext and edit). Installed internal Truemobile 1350 WLAN.
  • PC Card (not tested)
  • DVD+R Internal Philips working
  • Time Machine did loop through installation until I got another working (10.5.10) image and imported the User Profile (only!) via external USB. .

Inspiron 5160

  • Audio and LAN working out of the box
  • Onboard FX5200 GO video works with NVinjectGO 0.1.0
  • Install method: ToH RC2 - Update per How To to 10.5.1 . . .

Inspiron 6000

  • Install Method: Kalyway DVD & EFI
  • Processor: Pentium M
  • Chipset: Intel 915
  • Video: ATI Mobility Radeon X300
  • Wifi: Internal Intel 2200B/G I believe
  • SD Card Reader doesn't work
  • Firewire works

Result & Tips:

   Wiggle the mouse during install (every 5 mins or so) to avoid the Dell sleeping
   Formatted the drive with a single partition and GUID
   Do NOT use spaces in the label for the partition / hard drive (I used "Dell OSX 86" which failed, and "Dell_OSX_86" which worked)
   Select SSE2 from the install options (the Kalyway installer) and nothing else
   At this point, video works at 1024x800, Ethernet works, trackpad works, DVD works, Fn buttons for volume and brightness work, audio works.
   At this point, Wifi Doesn't work, and also iCal is broken.


   Downloaded http://z0rz.com/files/ATIScript.z0rz.v0.1.zip
   Follow the instructions and selected options "none 1280x1024x32 1 0" gave higher resolution
   Tried re-installing iCal using Pacifist, hasn't worked. .

Inspiron 640m

Installed from Kalyway DVD with EFI on MBR partition. Already had XP installed on the second partition. Can select to boot XP partition form the Darwin menu and it boots. After the install everything works except the Audio, for which I used the Taruga Path 1.20 and the Sigmatel 9200.txt dump. Intalled in Dual core mode with shuttering, disabled one core in the OS by modifying kernel flags "cpus=1" now its working fine.

  • CPU = Core 2 Duo 1.66GHz wrking with 1 core disabled
  • RAM = 1GB
  • Aud = Sigmatel 9200 HD Audio works with Taruga Patch
  • Vid = Intel 945GM Express works
  • LAN = Broadcom 440x works
  • WLAN = Broadcom 4311 Wireless works
  • BT = Broadcom Bluetooth module works
  • Dualboot with XP works

Inspiron 700m

Kalyway 10.5.1 DVD Install w/ EFI (MBR) and SSE2 as only items checked. Already had XP installed on second partition (and had third partition FAT32 for shared files) - Can select XP in Darwin menu to boot into XP

  • CPU = Pentium M (Centrino) 1.60GHz
  • RAM = 1.5GB
  • Aud = works
  • Vid = Intel 82852/82855 GM/GME Graphics Controller - works, but not full-res (only 1024 x 768)
  • LAN = Broadcom 440x works
  • WLAN = Intel 2915abg Wireless DOES NOT WORK
  • Dualboot with XP works

Inspiron 6400/e1505

  • Installation Method: Kalyway DVD w/ EFI
  • Processor: Intel Core 2 Duo T5500 @ 1.67GHz
  • Chipset: Intel 945GM
  • Audio works with AppleHDA & Taruga Patcher 1.20 & Stac9200.txt
  • LAN/WLAN works out of the box
  • Intel GMA950 works
  • DVD/CD drive works
  • MAKE SURE you choose "EFI MBR" during installation or else you will need the dvd to boot everytime
  • Has problems booting with 2 cores, resulting in choppy graphics, need to set "boot:cpus=1" or disable 'multicore support' in BIOS
  • Screen does NOT reactivate after closing the lid . .
  • Touchpad does not support scrolling .

Inspiron 6400/E1505 higher

  • Install Method: Kalyway 10.5.1 DVD with EFI(MBR): working with "vanilla" kernel
  • Processor: Intel Core 2 Duo T7200 @ 2.0 GHz (working only one core - BIOS settings at install, then "apple.com.boot.plist" edited)
  • RAM: 2x1 GB DDR2 PC5300 (667 MHz)
  • HDD: Toshiba MK1234GSX 120 GB SATA2 (four MBR primary partitions, Leo HFS+ on second partition, rest of them NTFS)
  • Chipset: Intel 945GM
  • Video Mobile Intel 945GM: working fine with QE/CI and fulll resolution 1280x800
  • Audio Sigmatel 9200 (patched with Taruga's 1.20&Sigmatel9200.txt): working without microfon
  • LAN Broadcom 440x 10/100 integrated: working fine
  • DVD-RW Philips SDVD8820: working fine
  • Firewire 400: working fine in connection to an iMac 17"
  • All 4 USB connectors: working fine
  • Intel Wireless 3945a/b/g: NOT WORKING YET!
  • Card Reader Ricoh 3 in 1: NOT WORKING!

Inspiron 9300

  • Install Method: Kalyway 10.5.1 DVD with SSE2 kernel and MBR
  • Processor: Pentium M Dothan 1.73GHz, 2 MB, 533 FSB (Bios not touched)
  • RAM: 2x512MB DDR2 533
  • HDD: Hitachi 80 GB (one partition)
  • 17" WXGA+ Video geForce Go 6800 working with Titan.kext at 1440x900
  • LAN Broadcom 440x 10/100 integrated: working fine
  • NEC DVD+/-RW DL 8X reading but writing not checked
  • Firewire 400: working fine in connection to an iMac 17"
  • All 4 USB connectors: working fine
  • Intel Wireless 2200BG: working unencrypted with iwi2200 Darwin drivers

Inspiron 9400/e1705

  • Install method: Uphuck 1.4i tiger upgrade to ToH Leopard + sortadan's post install patch (vanilla kernel, EFI) or Kalyway
  • Sigmatel 9200 audio working with AppleHDAPatcher and sigmatel9200.txt
  • LAN not tested
  • GeForce 7800go working with Natit for nVidia
  • Only one CPU core working. Must boot with the cpus=1 flag
  • Kalyway:
  • Audio works with file from this thread
  • Onboard Ethernet has disconnecting issues, fixed with $5 Airlink 101 USB Ethernet (Model ASOHOUSB) and driver here
  • Wifi with Intel 1345 doesn't work .

  • Install method: Kalyway 10.5.1 GUID or MBR EFI and Vanilla Kernel (Kalyway will allow boot after install with no additional steps)
  • Must install/boot by using cpus=1
  • ATI x1400 : Only up to 1440 x 900 with hack here ([4])
  • GeForce 7800go: Full QE/CI Working with NVInject for laptops on the Kalyway DVD
  • GeForce FX 1500m: Full QE/CI working with NVInject for laptops on the Kalyway DVD
  • GeForce FX 2500m: Full QE/CI Working after the Video ROM hack ([5]) that allow Mac to see 512mb instead of 256mb. Would STRONGLY RECOMMEND nvflash from true DOS not Dos Emulation in XP. Working with NVInject for laptops on Kalyway DVD
  • GeForce 7900 GTX 512mb: Testing
  • Audio Works by using AppleHDAPatcher v1.20 with the Sigmatel9200.txt ([6])
  • the Dell 802.11n Buildin PCI wireless works out of the box. Need to run the Applications->Utilities->Network Utility to see if it is using 802.11 a/b/g/n. If it is not, then you have to patch using AirPort_Extreme_802.11n_Enabler.dmg to enable the wireless-n speed ([7])
  • Hard drive works out of the box
  • Touch pad works out of the box
  • USB Works
  • Bluetooth detected and shows up but did not test functionality
  • Sleep works with Vanilla Kernel . .

Latitude 110L

  • Install Method: Kalyway - No EFI or Vanilla, SSE2 system
  • Processor: Pentium M 1.6GHz
  • BIOS Version: A08
  • Audio: Works out of the box
  • LAN: Not tested
  • Doesn't wake from sleep

Latitude D410

  • Install method: Kalyway DVD
  • Installation completed.
  • Video Card: Intel 915GM (external connector causes issues)
 Used pin out method: http://www.osxx86.info/showthread.php?t=117
  • Ethernet not recognized
  • WiFi not recognized, Intel 2200 b/g
Used iwidarwin: http://code.google.com/p/iwidarwin/
  • Bluetooth recognized out of box.
  • Will update with exact part numbers later. . . .

Latitude D420

  • Install method: Kalyway DVD 10.5.1
  • I turned off Multi-Core Support in the bios.
  • Installed perfect. Quartz Extreme worked out of the box.
  • Installed i8k fan driver. Seems to be working better (did this after 10.5.2 update). http://potatosaladx.blogspot.com/2007/05/i8kfangui-for-mac-os-x.html
  • LAN: Broadcom BCM5752 didn't work or try to get it to work. In 10.4.7 the network would freeze after 2 seconds of use. Figuring same problem in Leopard.. Using USB ethernet instead
  • WLAN: Intel 3945ABG not working. Ordered a Dell Truemobile 1490. Truemoble 1490 worked. Used last part of method described in this link:


sudo nano /Library/Preferences/SystemConfiguration/NetworkInterfaces.plist

You want to edit these lines:

<key>BSD Name</key>
---> <string>en0</string> (Change the en0 to en1)
---> <integer>0</integer> (Change the 0 to 1)

Thanks DrJohn. I rebooted after I did those changes and it worked.

  • Bluetooth worked out of the box.
  • Audio: Sigmatel 9200 Audio. Used AppleHDA Patcher 1.20 with Sigmatel 9200 file.
  • Note: After I installed I tried to turn back on multi-core and it just kept rebooting. Didn't even show login screen . .
  • Installed Kalyway 10.5.2 Combo Update. No problems. . . .
  • Sleep not working.

-- Melman101 . . . . . . . .

Latitude D530

  • Install Method: Kalyway - No EFI or Vanilla, SSE2 system
  • Processor: Core 2 Duo
  • Audio: Works with applehda.kext for 76A0
  • LAN: Doesn't work
  • To Install: (To fix LCD problem with LoginWindow.app)
    1. Gparted live cd partition, make mac partition active (use external usb sata case)
    2. Boot iATKOS 10.5.1 1.0ir2 DVD
    3. Select EFI bootloader, stock kernel, paulicat x3100, netkas smbios.kext, both io80211family kexts
    4. Gparted make xp partition active, copy chain0 to c: and add c:\chain0="Mac OSX" to last line of boot.ini, reboot, choose mac osx and boot into -s
    5. mount -uw /
    6. sudo -s
    7. rm -rf AppleIntelCPUPowerManagement.kext
    8. rm -rf AppleIntegratedframebuffer.kext
    9. rm -rf AppleIntelGMAx3100.kext
    10. rm -rf AppleIntelGMAx3100FB.kext
    11. Boot into vesa mode, replace both gmaxx3100.kexts with ones in zip (i think x3100 install option replaces natit.kext else replace it with paulicats)
    12. Add sleepdisplay.app to start up apps

Latitude 600

  • Install Method: Kalyway DVD
  • Processor: Pentium M
  • Audio: Sigmatel C-Major (Vendor Id:8086 Device Id: 24C5) works without patches
  • LAN: Broadcom 5701 Gigabit Integrated Controller (Vendor Id: 14E4 Device Id: 165D) works without patches
  • Dell Truemobile 1300 works without patches
  • PCMCIA/Cardbus doesn't work
  • Install Instructions: (This is for a fresh installation, for upgrade, see below)
    1. To install:
      • Format Hard Drive as MSDOS
      • Boot DVD
      • Partition as Journaled HFS+
      • Choose SSE2
      • Do not choose any drivers
      • Install
    2. After install, there will be a kernel panic. To fix:
      • Boot into -s mode
      • Run terminal
      • Delete the AppleBCM575x.kext file from your hard drive at: System/Library/Extensions/IONetworkingFamily.kext/Contents/Plugins/AppleBCM575x.kext
      • Reboot & Enjoy
  • If you "upgraded" from a previous version of OS 10, you may be faced with the problem of not being able to log in. Your passwords will not work including not having a password. You must boot into -s mode, reset the root password, reboot to the login screen, login as root with your new password, change the other User passwords or eliminate the other Users and create new ones to replace them. See here for a few methods of dealing with this

Latitude D610

  • Install method: Kalyway DVD
  • Audio: Works
  • LAN: Works
  • Dell wireless working
  • DVD drive working
  • Sleep not tested

Latitude D630

  • Install method: ToH RC2 + EFI v8
  • BIOS version AO4
  • Onboard Sigmatel 9205 Audio not working
  • LAN working
  • GMAX3100 graphics not working ; to boot IntelGMAX3100 kexts must be deleted ; VESA mode only
  • DVD drive working
  • Dell Wireless 1390 working ; recognized as native AirPort card . . .

Latitude D820

  • Install Method: Kalyway 10.5.1, GUID, EFI v8 patch
  • Audio works with sigmatel9200.txt codec, however does not mute speakers when headphones plugged in
  • Intel 3945 wifi NOT working (Dell Wireless 1490 bought on ebay for $13)
  • Broadcomm BCM57xx wired ethernet NOT working (using linksys USB200 dongle as a workaround)
  • Sleep/Resume works great
  • Will only boot with dual cores disabled
  • Geforce go 7200 works fantastic
  • ...
  • Install Method: iATKOS_v1.0ir2, vanilla EFI kernel
  • Audio works with AppleHDAPatcher v1.12 and stac9200-b.txt (DOES NOT with apple patcher 1.20 or sigmatel9200.txt)
  • Intel 3945 wifi NOT working, Broadcomm BCM57xx wired ethernet NOT working (using USB wifi for networking)
  • Sleep/Resume does NOT work. Also, occasionally reboot/shutdown do not work correctly, and the screen stays blank indefinitely, but holding the power button for 5 seconds from time to time seems to work and not have any noticeable consequences.
  • CPU: T7600 working fine at 2.33GHz
  • Will only boot with dual cores disabled
  • Geforce Go 7300 works via nvinject

Precision M6300

  • Install Method: Kalyway 10.5.1
  • Initial boot with this install image works but dies as soon as all the drivers and modules are loaded, com.apple.acpi.* panic.
  • Tried disabling virtualization and CPU execution bit but nothing.
  • Disabling the multicore support on the BIOS is what allows the operating system to try to boot without a kernel panic, but the whole thing comes to a screeching halt after an IOAPIC message. No matter what I try, the result is the same. I was unable to get around this problem.
  • However, Kalyway works fine (though very slow) on another laptop (Compaq C571NR). By creating an install to a USB disk (make sure it's partitioned as an MBR partition and ONLY use the MBR boot customization) and then bringing the USB disk to this laptop, it works.
  • After updating the 10.5.2 and using the NVidia 4.1 driver installer, the box screams light along like a bat out of hell.
  • Ran all of the Apple Software Updater updates for 10.5.2, machines purrs right along.
  • Wireless works right out of the box.
  • Audio does not work yet. .

Vostro 1400

  • Install Method: iATKOS v1.0ir2
  • Install Customization : Darwin x86 Bootloader + nothing else
  • Wireless works
  • Webcam works
  • Sleep, Restart, Shutdown works as first. No longer works after installation of nvinject.
  • Keyboard is a bit messed up
  • nVidia 8400M GS works with driver from alexcooltranquille (install after Leopard is already running).
  • Audio works only for headset plugin: use [Sigmatel 9228 codec] with AppleHDA Patcher version 1.16
  • Doesn't work : sleep/restart/shutdown, LAN (Broadcom 59xx does not have driver), card reader, bluetooth. . .

Vostro 1500

  • Install Method: Kalyway DVD
  • Audio doesn't work (Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 02))
  • LAN works, Wireless is not detected (Broadcom BCM4401-B0 Lan and Intel 3945 abg Wireless)
  • nVidia 8400GS M works with this driver from alexcooltranquille (Faster mirror here) .
  • ...
  • Install Method: iATKOS v1.0i
  • Audio works: first install the codec using AppleHDA Patcher v1.20 and the Stac9205.txt then copy the AppleHDA.kext and repair permissions. Note: internal mic still does not work.
  • LAN & Wireless work - Broadcom Lan and Dell 1390 wireless
  • nVidia 8400M GS works with nvinject
  • Integrated Webcam works . . . .
  • ...
  • Install Method: Kalyway DVD
  • Audio works with the above method.
  • LAN: untested; WiFi: Dell TruMobile 1390 (works), Intel 4965AGN (not detected);
  • Video: nVidia 8600M GT 256MB (works with above method)
  • USB (works)
  • SATA Mode: AHCI
  • Dell 355 Bluetooth (works)
  • Media Buttons (works), Dell remote (works)
  • Keyboard is not properly recognized, but works. . . . . . . .
  • ...
  • install method: Kalway 10.5.1 + GUID + EFI + BrazilMac = the perfect installation
  • Audio works by copying other working Kext into /System/Library/Extensions/, but not recognized in system preferences.
  • Video card GMAX3100 is the hardest part to configure: to install have to use -x (safe mode) to launch Darwin installer; after patching the Kext from EFI_V8.0, internal LCD only works with -x mode; have to install Natit.kext and remove AppleIntelGMA950* and AppleIntelIntegrated* to get video works with external monitor at normal mode, i.e., 1400x1050 on Intel GMA X3100 with full QE/CI. That's the best I can get so far(please keep update this part, if I miss something)

Vostro 1700

  • Install Method: iATKOS v1.0i
  • Audio doesn't work
  • LAN & Wireless work
  • nVidia 8600M GT works with this driver from alexcooltranquille . . . .
  • ...
  • Install Method: Kalyway Leopard 10.5.1 - Both EFI 8/ VANILLA
  • Audio works: first install the codec using AppleHDA Patcher v1.20 and the Stac9205.txt then copy the AppleHDA.kext and repair permissions
  • LAN & Wireless works out of the box
  • nVidia 8600M GT works with Nvinject- this . . . . . .
  • Both cores working- Super fast!
  • Faster than MacBook Pro .

XPS m1330

  • Install Method: iATKOS EFI
  • Processor: Core 2 Duo @ 1.83GHz
  • Audio (Sigmatel 9228) - Only the headphone jack works
  • LAN doesn't work
  • Truemobile 350 & 1390 works
  • Geforce 8400M GS works with QI/CE at 1280x800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


Amilo Pi 1556

  • Install method: ToH RC2 + EFI v8
  • BIOS version 2.5
  • Audio working line out with AzaliaAudioFix
  • LAN working out of the box
  • GeForce 7600GO graphics working with NVinjectGO 0.0.9 or gfx_string from pc_efi here
  • Intel 3945 Wireless not working
  • Card Reader working
  • CardBus and TV Out not tested .

Amilo Pro V3545

  • Install method: Kalyway 10.5.1 clean MBR install w/ flag "cpus=1" all the time.
  • Processor: Intel Core Duo @1.66
  • Installed on a USB External Disk
  • Audio working
  • GeForce GO 7300 128M graphics working w/ NVInjectGO
  • TouchPad working
  • LAN doesn't seem to work (need to read about it)
  • Wireless doesn't work (need to read about it)

ESPRIMO Mobile V5505

  • Install method: iAtkos v1.0i with EFI
  • Dual Boot with Vista using Darwin
  • BIOS version A0Z
  • Audio working (headphones not working)
  • LAN working
  • X3100 graphics FULLY working with the driver provided with iAtkos
  • Intel Wireless not working (driver does not exist - replaced with broadcom 4311 (this one was from HP Pavilion dv6000 - working OOB))
  • Card Reader working
  • sleep mode not working
  • Battery indicator working OOB but not on the stock kernel (see: http://forum.insanelymac.com/index.php?showtopic=80425 for more info) .



  • Install Method: Kalyway 10.5.1, 10.5.2 Kalyway Combo Update
  • Only OS X installed.
  • 855GME works but only at 1024x768, no CI or QE. We need a leopard driver for the 0x35828086!!
  • Broadcomm Intregrated ethernet works OOB, if u install 10.5.2 Kalyway update it breaks. My wl-167g does work though on 10.5.2 with ralink drivers
  • Built in wireless does NOT work. modem jack not tested.
  • USB works fine, firewire recognized but not tested. VGA out port not tested.
  • Sound recognized as AC97 but does not work at the moment. Shows up in System Preferences>Sound but in System Profiler says No built in audio.
  • In bios you must disable USB legacy before u install to get keyboard and trackpad to work.


  • Install Method: iATKOS v1.0i - EFI emulation running stock kernel
  • Dual Boot with XP using Darwin
  • ATI x1400 works but only at 1024x768
  • Intregrated Intel 10/100/1000 mbps ethernet works with IONetworkingFamily.kext
  • Intel 3945abg wireless does NOT work.
  • USB works
  • SigmaTel 9250 (7634) Audio works with AppleHDAPatcher 1.20 (http://forum.insanelymac.com/index.php?showtopic=32859) used with Sigmatel9250.txt codec dump from (http://psykopat.free.fr/apple/AppleHDA/sigmatel/)
  • Tablet PC functionality does NOT work (not surprising).


  • Install Method: BrazilMac patched DVD on GPT with EFI v8.0
  • Audio works with patch
  • LAN & USB works
  • Complete install instructions here .


  • Install Method: Kelyway 10.5.1
  • Dual Boot with XP using MBR
  • SigmaTel STAC-9250 Audio does not work
  • Marvell Yukon LAN 88e038 does not work
  • Broadcom 1490 wireless card works
  • Restart does not work . . . .

HP (Hewlett-Packard)

HP Pavillion DV 9530 ef

  • OS kallaway
  • Nvidia 8400G Worked with with NVInstaller v.31 http://scottdangel.com/blog/?p=18
  • Audio Intel High Def Audio ALC 268 Working after installing Tagura ALC 268] Installer
  • Bluetooth working
  • Keyboard: working
  • Ethernet: Working-After download driver on the official site realtek

HP Pavillion Dv 6516Tx

  • OS- iATKOS v1.0 ir1 and ir2-
  • Nvidia 8400G Worked with after installing Nvida Installer Select 128mb
  • External Display- Does not Detect Displays.--but says supported in System Prefrences
  • Audio : Intel High Def Audio Working after installing Tagura ALC 286 Installer
  • Mic: Working after Tagura ALC286 Installer
  • Keyboard: working OTB
  • Touchpad: working OTB-With tapping-Scrolling not active-
  • USB: working OTB
  • FIREWIRE (400 Mbps) OTB
  • Bluetooth working OTB--ONLY SENDING- no Reciption
  • HP Remote Working for Volume OTB, Cannot Open Front Row
  • HP Quick Launch Buttons-Only Volume Slider Working, OTB. Mute Inactive
  • HP Webcam Not acceable via PhotoBooth, But works in Yahoo Messenger.
  • Wireless Slider Button Works only for Bluetooth
  • CD Drive * Matisha* CD/DVD Writer Working OTB---This Drive was Replacement for TSST Corp Drive
  • Ethernet: OTB
  • Wireless: internet Intel Wireless Pro 3945 A/B/G not working-Not able to download Driver

Works Really well , But some times Becomes Sluggish- Remedy _ connect Iphone or Apple Mighty Mouse " it returns to normal self. . . . . . . . . . . . . . . . . . . . . .

HP compaq 6710b

  • OS : 10.5.1 Kalaway
  • CPU : Intel Core 2 Duo T7100 @ 1,8 GHz (2048 kB Cache)
  • Memory : 2048 MB DDR2 667 MHz
  • Video Card : Intel GMAX3100 working in native with Original drivers, Kalaway drivers dont work
  • Audio : ADI soundmax ?
  • Keyboard: working
  • Touchpad: working
  • PC Express 54 working
  • USB: working
  • FIREWIRE OK (400 Mbps)
  • Ethernet: internal Broadcom NOT working
  • Wireless: internet Intel Wireless Pro 3945 A/B/G not working

Pavilion dv2175ea

  • OS : 10.5.1 Kalway
  • CPU : Intel Core 2 Duo T5500 @ 1,66 GHz (2048 kB Cache)
  • Memory : 2048 MB DDR2 667 MHz
  • Video Card : Nvidia Geforce Go 7200
  • Audio : Connexant HD Audio // output only (headphone out not working, all quickplay and laptop facia buttons working tho)
  • Bluetooth OK right out of the box
  • Keyboard: working
  • Touchpad: working
  • PC Express 54 working
  • USB: working
  • FIREWIRE OK (400 Mbps)
  • Ethernet: internal Intel Pro NOT working
  • Wireless: internet Intel Wireless Pro 3945 A/B/G not working
  • MOTU 828 external firewire working sweeeeet
  • Logic 8 pro working sweeeeet
  • Having no internet/ethernet is a pain, but no other probs at all, 10.5.1 runs sweet as on this laptop ;) so did 10.4.6 before it. . . .

HP Pavilion DV6000

HP Pavilion DV6000

OS: iAtkos v1.0i

Memory: 1GB 533 MHz DDR2 SDRAM


Keyboard and TouchPad: Working

Internet: Wi-Fi Working Ethernet not working.

USB: Working

S-Video: not working.

headphones: Not working.

Microphone: Not working.

Updates; Working Except 10.5.2 (that I had to download kalyway ComboUpdate) .


Pavilion 1659 us

  • Install Method: Kalyway DVD 10.5.1 with PC-EFI & Vanilla Kernel MBR NO Other Kexts
  • Processor: Intel Centrino Duo 1.6 GHz
  • Audio & LAN work (use Intel8255x kext from Genius Bar to fix )
  • SATA works
  • DVD works
  • Onboard GMA950 works. (And in 10.5.2, but NOT with Graphics Update 1.0)
  • Wireless: Broadcom 4312 (swapped out 3945 for this alternative mini PCI-E HP part) works, after installing Airport Extreme Update 2007-002 from Apple site, using Pacifist to extract kexts, but NOT the frameworks. This fixes IO80211NetworkingFamily.kext. Appears as Airport in task bar. Wireless Works even better in 10.5.2
  • Gives score of 78 in Xbench


  • Install Method: Kalyway 10.5.1
  • Tech specs: Intel Celeron M 1,4Ghz (SSE2), 1280Mb DDR RAM, 160GB Segate HDD, Broadcom wlan and ethernet, GMA900 64Mb, onboard audio
  • working: WiFi, ethernet, sound, dvd (burning), sleep and wake up, battery status, USB hubs, no kernel panics
  • everyday booting is possible only with paperclip inserted (pin 6 and 12) to avoid "blue screen of death" or external monitor attached
  • not working: bluetooth, PCMCIA, 3D acceleration without Quartz Extreme and Core Image (software only) ANY IDEAS???
  • system is very stable, no additional fixes needed . . . . . .

dv9500t CTO

  • Install Method: Kalyway 10.5.1 w/ PC_EFI 8.0, Vanilla Kernel, Do NOT select 'SSE2' package during installation.
  • Tech specs: Intel Core 2 Duo T7250 2.0GHz, 2048MB DDR2 SDRAM, 2x 120GB SATA 5400rpm Drives, 256MB nVidia 8600m GS, Onboard Intel HD Audio (Realtek ALC268), Integrated Webcam, 2 Integrated Microphones, 2 Integrated Headphone output jacks, HDMI and VGA Output, Intel 4965 AGN Wireless, Bluetooth
  • Working: Onboard ethernet, DVD burning, Bluetooth, nVidia works, but do NOT select nvinject during install, the system would not boot after installation with nvinject. Instead use standard drivers during install and download NVInstaller v.3. Onboard audio works with the following driver (use ALC268_Installer2.zip) - [8], HDMI-out (auto starts on detection of display)
  • Not working: Sleep Mode; Battery Meter; Onboard webcam - Webcam power LED turns on when Photo Booth starts, but no video is displayed; Intel 4965 AGN WiFi; Touchpad page scrolling; NumLock has no effect on right-hand side numpad; Delete key has no effect when used on files.
  • Not tested: VGA
  • Notes: Installation, once I got all the correct package settings, was totally painless. . . . . . . .


  • Install Method: Kalyway 10.5.1 w/PC_EFI 8.0
  • Vanilla Kernel Crashed after 20 seconds, used ToH patched kernel
  • Audio & LAN out of box using driver on the DVD
  • No QE on the integrated GMA915
  • Wireless doesn't work


  • Install Method: Kalyway 10.5.1 w/PC_EFI 8.0
  • Processor: Intel Centrino Duo 1.6 GHz
  • Audio/vid/dvd work(select before install with DVD "configure" options)
  • Ethernet/Lan work (Intel Pro/100 VE); used how to install guide.
  • boot, reboot, power down work. .

Pavilion dv6113ea

  • Install Method: Kalyway DVD with PC-EFI & Vanilla Kernel
  • Processor: Intel Centrino Duo 1.6 GHz
  • Audio & LAN word
  • SATA works
  • Onboard GMA950 works
  • Intel 3945ABG Wifi doesn't work

Pavilion dv6314ea

  • Install Method: iATKOS 1.0 DVD with PC-EFI
  • Processor: Intel Centrino Duo 1.73 GHz
  • Memory 1Gb
  • Wireless Intel 80211 LAN works flawlessly
  • Audio Conexant HD works partially: no mic input, no phone output;
  • SATA works OK
  • Onboard Intel GMA950 works out of the box
  • Broadcom Lan works
  • Many keyboards shortcuts work just as in HP
  • Synaptic mouse touchpad works completely
  • USB and firewire OK
  • Restart and shutdown OK, sleep though doesn't work
  • Overall performance is very good

Pavilion dv6330ea

  • Install Method: iATKOS v1.0i
  • Processor: Intel Core Duo T2350 @ 1.6 GHz
  • Audio: Works - however the headphone socket does not.
  • Ethernet: Works
  • SATA: Works
  • nVidia 7400 Go: Works w/ the Nitat driver
  • Wireless Intel 3945ABG doesn't work - as per usual
  • Integrated Webcam works
  • DVD Burner works
  • Card reader still to be tested.

Pavilion dv6345us

  • Install Method: iATKOS v1.0r2
  • Audio & Ethernet work
  • SATA & IDE work
  • Wireless Intel Intel 3945/ABG doesn't work
  • Integrated graphics with QE/CI and Dual Screen work
  • Integrated HP Webcam works out of box
  • Card reader doesn't work

Pavilion dv6401

Install method - Kalway disk bar install

  • Not working buty patchable: onboard lan . .

Pavilion dv6699el

  • Install Method: Toh rc2
  • Audio & Ethernet work
  • SATA & IDE work
  • Wireless Intel Intel 3945/ABG doesn't work
  • GeForce 8400M GM works
  • Integrated HP Webcam works out of box
  • Card reader doesn't works . .


  • Install Method: Kalyway 10.5.1
  • Audio & Ethernet work
  • SATA & IDE work
  • Wireless Intel Intel 3945/ABG doesn't work
  • GeForce 8400M GM works
  • Integrated HP Webcam works out of box
  • Card reader doesn't works
  • Bluetootk works


  • Install method: Zephyroth 10.5.1 AMD DVD
  • Audio Conexant/SB400 fully working
  • Keyboard keys work after installing ApplePS2Controller.kext
  • Wireless working out of the box
  • Ethernet and FireWire detected but not tested
  • Fan is moderated if unplugged
  • Integrated ATI graphics not fully tested (Resolution change works though with Callisto Build 3)
  • DVD Drive working
  • Card Reader not working . . .

Pavillion dv9379ea

  • Install method: BrazilMac + 10.5.1 Update + Patched vanilla kernel (b13 upgrade method)
  • Everything working except Intel 3945 Wireless and Card Reader
  • Graphics work with NVInjectGo 0.1.0
  • QE/CI (to function properly without crash) needs a reboot to Vista and a shutdown
  • com.Apple.boot.plist kernel strings:

HP 2710p Tablet PC

  • Install method: iAtkos v1.0i (Customize: choose main OS and VGA: Intel x3100 only)
  • Install Darwin bootloader; didn't try EFI yet.
  • Intel Core 2 Duo 1.06GHz, U7500
  • 2 GB RAM, 100GB Toshiba Hard drive
  • As of now Audio & WLAN (Intel) not working
  • Key board, Synaptics pointing device working.

platform=X86PC -legacy -v . . . . . . . . . . . . . . . . . . . . . . . . .

HP NC6400


  • OS Kalyway 10.5.1
  • Must use cpus=1 during install or disable second core in BIOS. Edit com.apple.Boot,plist later to add cpus=1 in kernel flags section
  • Intel GMA 950 works out of the box
  • Audio works for a minute or so and goes mute after, When pressed mute button oin keyboard it does come back for another minute and so on. No workaround yet.
  • Bluetooth not tested.
  • Keyboard: working
  • Ethernet: Not working
  • Wireless Intel not working, in process of getting D-Link WUA-1340 USB dongle, reportedly working.
  • NOTE: When rebooting it will go to the loop during registering, boot to single user mode -s and nount / to rw mode:

/sbin/mount -uw / and after that change root password:

  • passwd root

to whatever you want. Finally type:

  • touch /var/db/.AppleSetupDone
  • reboot

And that should do it. . . . . .



  • Install Method: iATKOS V1.0
  • Audio: No sound!!,Volume and mute buttons work
  • Video: works great
  • Ethernet: not worksing
  • WiFi: not working
  • Mouse: Trackpad & Nipple works .

R61 tpye:8919

Install method: Kalway 10.5.1 bare install - NO options but efi loader Working:

  • Trackpad mouse pointer
  • bluetooth
  • usb, firewire and built-in camera
  • Base video support: No QE CI Nvidia nvs 140m

Not working:

  • onboard nic: Intel 82566MC
  • wireless nic: intel 3945
  • Sound: AD1894 HD audio

Battery indicator works using patch: http://forum.osx86project.org/index.php?showtopic=14912 . . .


  • Install Method: Kalyway (SSE2)
  • Audio: Volume and mute buttons work, Mic works, Playback works
  • Video: works,but QE Disable
  • Ethernet: works
  • WiFi: not working
  • Mouse: Trackpad & Nipple works


Type (2373-CT0)

  • Install Method: Kalyway (SSE2 & MBR)
  • Audio: Volume and mute buttons work, Mic works, Playback works
  • Video: works (ATI Mobility Radeon 7500)
  • Ethernet: works (Intel PRO 1000/MT mini-PCI)
  • Internal WiFi: not working (Intel 2200bg mini-PCI)
 look for USB options based on Ralink, or Atheros mini-PCI allegedly works
 I got a Belkin F5D7050 v5xxx USB 802.11bg from Staples working with the Zydas drivers
  • Mouse: Trackpad & Nipple works
  • Sleep: not working
  • Dashboard: works.


  • Install Method: Kalyway (no issues during installation)
  • Audio: Volume and mute buttons work, Mic works, Playback works
  • Video: works great
  • Ethernet: works
  • WiFi: not working
  • Mouse: Trackpad & Nipple works . .

-- Just tried 10.5.1 on a T43, and in verbose mode everything works great until you get to the first blue screen, then a whole lotta nothin'.


  • Install method: Kalyway 10.5.1, Vanilla, GUID
  • Audio works with this patch
  • LAN and GMA950 working out of the box
  • Wireless not working
  • SATA working , IDE not tested .

T60 1952-CTO

  • Install method: Kalyway 10.5.1, ToH, MBR
  • Audio works with this patch (only output)
  • LAN and GMA950 working out of the box
  • Wireless not working; switched to Atheros 5008 802.11abgn adapter (working out of box)
  • SATA working
  • Speedstep working with patched kernel (unstable on freq switches)
  • speedstep.app is unstable ( package - follow instructions - remove speedstep.app - use acpicputhrottle instead)
  • sleep does not work (0192 bios error - security hardware tampered)
  • display brightness keys with old AppleIntelIntegratedFramebuffer.kext
  • fingerprint reader works with UPEK USB drivers
  • switching from external to internal lcd not working
  • DVI over advanced mini-dock not working. . . . . . . . . .

T60 1955-A13

  • Install method: IAktos 1.0r2 (10.5.1), MBR
  • Audio, Lan, GMA 950 working out of the box
  • Wireless not working
  • SATA working
  • DVI in Dockingstation does not work
  • VGA does work in Dockingstation and directly connected
  • Switching Displays is working

R52 1860-W2Z

  • Install Method: Kalyway (need -x -c to boot on disk, only EFI mbr)
  • Audio: Volume buttons works, mute buttons works, Mic work, Playback not tested yet
  • Video: works good (no opengl yet)
  • Ethernet: works
  • Wifi: not working
  • Mouse: Trackpad & Nipple works . . . . .


  • Install Method: Kalyway (SSE2)
  • Audio: Volume and mute buttons work, Mic works, Playback works
  • Video: works,but QE Disable
  • Ethernet: works
  • WiFi: not working
  • Mouse: Trackpad & Nipple works


  • Install Method: Kalyway.

The ONLY option I selected at Install Customization is EFI MBR Bootloader. As far as I understand, this means that the kernel installed is NOT the vanilla kernel. After the installation is complete the machine might not boot, or constantly reboot. I managed to get past that point by going in the BIOS (F1 at startup) and disabling multicore support (under CPU), and putting SATA in compatibility mode. Later, after I made a bunch of other modifications, the machine was able to boot with dualcore and AHCI mode for the SATA controller. I don't know which modifications made that possible :-)

  • Wireless: You MUST replace the Intel card with an IBM/Atheros one. Having done so:

sudo nano System/Library/Extensions/IO80211Family.kext/Contents/PlugIns/AirPortAtheros.kext/Contents/Info.plist Add: <string>pci168c,1014</string> Fix ownership and permissions per the guide above.

  • Audio: Volume and mute buttons work after following the Sound instructions at

http://forum.thinkpads.com/viewtopic.php?t=37624, Fix ownership and permissions per the guide above.

Microphone and line-in do not work. If you want to use skype, one option is to get a USB camera and install the program macam so that you can use the camera's microphone.

Fix ownership and permissions per the guide above.

Updating to 10.5.2: I only installed the non-OSX updates, i.e., itunes, quicktime, etc. That temporarily broke the system. To solve this, press F8 at boot time and select -x -f. This rebuilds the kext caches and boots in safe mode. Rebooting once more (without any options now), seems to do the trick. .

Y510 IdeaBook

  • Install Method: Kalyway 10.5.1

Boot install dvd with cpus=1 -v option. Install normally with efi and vanilla kernel w/ ps2 fix First boot hangs after install with KPI error. Debugged and found solution from this thread . Replaced with file from this post.[9] Boot again with -v -x -legacy options and finally boots to osx. Had to repair file permissions and got a fully functional osx install minus the intel 3945 wireless. . . . . . .


Megabook L745 T2522DL

  • Install method: iATKOS with Bootloader install script
  • Audio output working with ALC882 driver from Tiger, input not working
  • LAN working [out of the box ??]
  • Graphics fully working with Natit 7600GO Installer (dual screen not tested)
  • SATA and IDE working
  • Integrated 1.3 Megapixel Webcam not tested


Olibook 610-430 (ECS/Uniwill Barebone)

  • Install Method: Kalyway 10.5.1 & Iatkos (with funny install guide found at InsanelyMac)
  • Processor: Intel Celeron M 430 (1.73ghz) Core Solo Yonah
  • Chipset: Intel 945GM1940GML
  • Video: Intel GMA 945 - Works with QE/CI enabled, can change resolutions for the internal and external monitor. Minor mouse tearing / artifacts in Firefox 3 and MS Office. Quake 3 works great. S-Video TV Out doesn't work, stays at blue screen when booting.
  • Audio: Realtek ALC883 - Works with headphones or external speakers, mic-in not tested. There's a way to enable internal speakers with a patch but then line-out doesn't work. SPDIF Not tested.
  • LAN: Realtek 8139 - Works OK.
  • Wi-Fi: Intel PRO/Wireless 3945ABG - NOT WORKING
  • Touch pad: Works OK.
  • USB ports: All working. Tested with Logitech MX518, A4Tech Spanish Keyboard (all keys detected) and Sony Ericsson Z550a.
  • Power Management: Sleep didn't tested. Battery meter works with iatkos.
  • SATA: Works OK. . .


Aura R20

  • Install Method: Kalyway DVD
  • Processor: Intel Core Duo @ 1.73
  • Chipset: ATI x1250
  • Audio: Works with HDA ALC patch
  • LAN: Works out of the box
  • Wireless works out of the box
  • ATI x1250 video fully works

Samsung Q45 AV01

  • Kalyway Mac OS X 10.5.1 with EFI v8 + Darwin 9.1.0 Speed step Kernel.
  • Intel Core2 Duo T7300 (Work perfect)
  • PM965+ICH8M (Work perfect)
  • DDR II 667MHz 1GBX2 (Work perfect)
  • 12.1�WXGAG Samsung LCD (Work, But Can�t control Brightness)
  • NVIDIA GeForce 8400M G with 128Mb DDRII (Work perfect)
  • Realtek High Definition Audio ALC262 (Work perfect with Headphone Output & Mic input)
  • Marvell Yukon 88E8039 PCI-E Ethernet (Work perfect)
  • Bluetooth 2.0+EDR (Work perfect)
  • Intel(R) PRO/Wireless 3945ABG (Not work, as all the other�s)
  • Agere Systems HDA Modem (Not work, working on it…)
  • PC Card (Work perfect)
  • 130 Mage Camera (Work perfect)
  • 120G SATA Hitachi 120G HD (Work perfect wiht Vista in other Volume)
  • TSSTcorp CD/DVDW Super-Multi Driver (Work perfect With RPC-1 Firmware)

Reboot are also working perfect, but it has a "Shutdown" & �wake up”�problem cause I�m using a crack kernel for Intel SpeedStep.

Samsung R70-A003

  • Install source: Kalyway 10.5.1 (later updated to 10.5.2)
  • CPU: Intel Core2Duo T7300
  • Chipset: Intel 965PM + ICH8M
  • HDD + DVD: works out of the box (not tested CD/DVD burning)
  • Video: nVidia GeForce 8400M GS (works, install instructions)
  • Camera: Vega USB 2.0 (works out of the box)
  • WiFi: Intel 3945ABG (not working)
  • Ethernet: Marvell Yukon 88E8039 (works after some patching, hint: use Google to translate this page from Korean to you native language)
  • Sound: partially works (using AZALIA_out), speakers only


Vaio VGN-FS415MR

  • Install Method: Kalyway (SSE2 System, Azalia_out, GUID)
  • Processor: Intel Pentium M, SSE2, 1700 mHz
  • Audio: Speakers work
  • LAN work

Vaio VGN-FZ21Z

  • Install Method: AITKOS [Darwin EFI Boot Loader, Stock AppleACPIPlatform.kext, Stock Kernel]
  • Processor: Intel Core 2 Duo T7500, SSE3, 2.20 GHz
  • Audio: Speakers & Headphone jack work after AppleHDAPatcherv1.20 with sigmatel_7662.txt
  • LAN: works after updating AppleYukon2.kext/Contents/Info.plist for Yukon 88E8036 card [Vendor: 11ab Device: 4351]
  • Wifi: doesn't work
  • VGA: Nvidia GeForce 8600M GS. Currently I can only get this to work in vanilla resolution
  • Laptop fan does not adjust speed - Laptop runs hot. Working on this and Video Card.


  • Install Method: Kalyway with Vanilla with ACPI support
  • Processor: Core 2 Duo
  • Chipset: Intel 945
  • Internal speakers work with Azalia
  • Wifi doesn't work

Vaio VGN-N365

  • Install Method: Kalyway (Vanilla, EFI, AzaliaAudio, MBR)
  • Processor: Core Duo T2450
  • Chipset: Intel 945GM
  • Audio: Speakers work, ports don't work
  • LAN doesn't work
  • Atheros Lan-Express works out of the box
  • Modem & Card Reader don't work
  • ExpressCard slot not tested

Vaio VGN-N330FH

Install Method: Kalyway with Vanilla and MBR with windows XP on first partition Processor: Core Duo T2080 1.73GHz with both cores working Chipset: Intel 945G working with small artifacts Audio: speakers, headphone and mic ports working with [10] Lan : Ethernet working and WiFI detected as airport working Modem and card reader dont work MemoryStick port not tested ExpressCard slot not tested FireWire port working

so, only a few minor things doesnt work. 112 in xbench

Vaio VGN-NR 11S/S

  • Install Method: iAKTOS 1.0ir2 and (Kalyway + patch x3100)
  • Processor: Core Duo T5250 (both cores working)
  • SATA & IDE work
  • Chipset: Intel GM965 Express (GMA x3100) work
  • Audio: Speakers work, microphone & headphones don't work,
  • LAN: Marvell Yukon 88E8039 work with this extensions file for more read here
  • Wireless 3945ABG Intel don't work
  • Modem & Card Reader don't work
  • ExpressCard slot not tested
  • external VGA port not tested
  • Firewire port OK (don't boot)
  • 4 port USB OK
  • boot from usb disk external OK: (iAKTOS and Kalyway)

. . . . . . .


Equium A200-1V0

  • Install Method: iATKOS 1.0i r2 (Untested/no EFI, Remove CPUPowerMAnagement + Thermal Drivers via install)
  • Processor: Intel Pentium Dual-Core T2310 @ 1.46Ghz (Both cores working)
  • Chipset: GL960 Express + ICH8M
  • Audio: Intel HD Audio ICH8 (0x1179FF10) - Output works, no input device detected + no speaker cut-off bug
  • LAN: Marvell Yukon 88E8039 (Supplied Yukon2 driver works, but needs Info.plist modification)
  • Video: GMA x3100 / 965 (Working+QE/CI - driver supplied)
  • SATA: Working
  • WiFi: Realtek 8197 (Working with 8187B Driver - requires vendor:poductid mod in Info.plist)
  • Notes: Don't install Yukon2 drivers until after installation to prevent a looping bug at user-creation. Boot-sector wasn't installed properly - to fix, I formatted an HFS+ partition from JaS 10.4.8 DVD first.

Satellite A100-813

  • Install Method: iAKTOS 1.0i + EFI
  • Processor: Core 2 Duo T7200 @ 1.99GHz
  • Audi works with AppleHDA Patcher by Taruga
  • LAN works out of the box
  • Intel 3945 Wireless doesn't work
  • Card Reader doesn't work . . . . . . .

Satellite Pro A100 PSAACE-00400DG3

  • Install Method: iATKOS v1.0i rev. 2
  • Processor: Intel® Centrino Duo
  • Chipset: Intel ICH7R
  • Audio & LAN work
  • Video: ATI Mobility Radeon x1600
  • Video needs the [ATIMobileX1600Pack.zip http://www.itgo2u.com/yhDEV/OSX/ATIMobileX1600Pack.zip] drivers
  • SATA & IDE works
  • Intel® PRO/Wireless 3945ABG does not work . . .
  • PCMCIA Port does not work
  • Toshiba Bluetooth does not work
  • SAN DISK Drive does not work .

Satellite Pro A100-830 PSAACE00W002EN

(Note: Have now upgraded to 10.5.2 but could probably have got same hardware working)

  • Install method: Kalyway 10.5.1 install DVD [lost my window partitions somehow!!]
  • Processor: Intel Centrino Duo T7200 2 Ghz (both cores detected)
  • Chipset: Intel® 945PM Express
  • Display: 15.4" TFT Display 1280 x 800
  • Video : ATI Mobility Radeon X1600 256 MB (Device ID: 0x71c5)

could only get this partially working

  • Audio: Intel High Definition Audio (ID: 0x1179FF10) working with AzaliaAudio.pkg
  • Wireless Intel PRO 3945ABG not yet working but drivers under development

installed Broadcom 4311 (Dell branded) instead and that works out of the box.

Satellite A135-S4487

  • Install method: iATKOS v1.0; Vista dual boot from the Wiki OSX86 10.5.1 guide
  • Processor: Intel® Core Duo T2250 1.73 GHz, both cores recognized
  • Audio: Realtek HD audio works, including volume wheel, with no patches
  • Video: Mobile Intel 945GM express works (all resolutions) with no patches
  • USB works
  • LAN: Realtek RTL8101 works
  • Touchpad works
  • DVD reader works, burner not tested
  • Intel® PRO/Wireless 3945ABG does not work as expected :>(
  • Dell Truemobile 1490 works with tape over pin 20; front panel wifi switch and LED no longer work
  • PCMCIA Port doesn't work
  • Card reader doesn't work
  • Headphone jack doesn't work
  • Microphone not tested
  • Firewire not tested
  • Sleep: can't wake up from
  • Can't modify power options
  • Battery meter works only on % left not time remaining
  • Only get 30 minutes on battery! . . . . . .

Satellite A200 AG

  • Install Method: iATKOS v1.0i rev. 2
  • Processor: Intel® Core™2 Duo CPU T7300
  • Chipset: Intel 965M
  • Audio & LAN work
  • Video: ATI Radeon HD2600
  • Video needs the Triakis_2400_2600_2900_3800 video driver
  • SATA & IDE works

Satellite A205-S5804

  • Installed via iATKOS v1.0i + EFI; Choose "Darwin EFI bootloader" & "stock kernel"; Removed CPUPowerManagement driver & removed thermal kexts
  • Dual Core and SpeedStep working. Might need the extra SpeedStep app included the installer.
  • Intel GMAX3100 fully working with Paulicat's natit.kext for X3100 [11] revision 2 of the installer have the driver included; LCD would not function until this was loaded; external video worked fine though.
  • Realtek 8187b wireless working with driver from [12]; Had to change Device ID from 33161 to 33175 in Info.plist
  • DVD Burner untested; System Profiler shows it as supported
  • Audio works with no modifications; analog headphone doesn't work, microphone not tested; USB headphone works
  • USB 2.0 fully working
  • Wireless on/off button works
  • Volume control wheel works; no other special keys working
  • Power Management doesn't fully work (no sleep, no battery meter) . . . . . . . . . . . . . .

Satellite M115-s3094


Installed from iATKOS v1.0i;Choose "Darwin bootloader" ;& "stock kernel"; Removed CPUPowerManagement driver & removed thermal kexts,after the install Everything working exept microphone,for wireless I used a Belkin f5d7050 adapter and installed a Ralink driver(10.4)from Ralink page,battery meter working . . . . . . . . . . . . . . . . . . . . . . . . . . .


Installed from iATKOS v1.0iv2; Chose "EFI" & "stock kernel" [1 & 2 in list] No VGA driver checked.

Before install I replaced the built-in wireless card [Intel 3945abg] with a Dell TrueMobile. Worked OOB with no extra drivers.

Haven't tried wired Ether. FireWire port is recognized [have not tried it]. Sound works OOB. USB HD mounts. Microphone not recognized.

Screen resolution works. Fan on all the time. No battery indicator. . .

Satellite m70 167

Installed from kalyway 10.5.1 in dual boot mode with windows xp (MBR)

Everything working exept wireless. I'have installed leopard by twenty minuts and don't know if there is other that not work. I have used external lcd monitor for install process and for reboot problem I have typed in boot "tohkernel cpus=1" . . .

Blue screen "the intel 915GM Express chipset problem" I have resolved with the dongle "1-wire trick" battery level from iakatos release language pack from toh release . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Powered by MediaWiki © 2021 OSx86 Project  |   InsanelyMac  |   Forum  |   OSx86 Wiki   |   Privacy policy   |   About OSx86   |   Disclaimers