This is a component level hardware compatibility list. We want to keep it as accurate as possible, but please, do not entirely rely on this list when buying hardware. Add which parts you have working in the categories listed below, or create a new category. Please keep alphabetical order inside the categories. The categories themselves are ordered by popularity. Please list any caveats or problems as well.
| Hardware Name (alphabetical)
|
Chipset
|
Notes
|
EFI/Vanilla kernel working
|
Fully Working w/o Patch
|
| AB9 QuadGT
|
Intel P965 & ICH8R
|
- Install Method: Kalyway 10.5.1 & Combo Update
- BIOS Version: Unknown; Revision: Unknown
- Audio: Works with patch below
- LAN: Unknown
- SATA & IDE: Problem
- Install Instructions:
- Partitioned as MBR
- Installed using Vanilla Kernel, and MBR selections under customize
- Complete Install and Reboot
- Use -x on first boot
- Setup First boot in safemode
- Use kexthelper (here) to install kexts below
- Install Sound Driver for Onboard sound from here
|
EFI & Vanilla Kernel works
|
Audio Needs patching
|
| AW9D-MAX
|
Intel 975X
|
- Install Method: Leopard-10.5.2-AMD-EFI.iso DVD
- BIOS Version: 15; Board Revision: 1
- Audio: WORKS With AzaliaAudio (from DVD)
- LAN: Both WORK OOB
- SATA & IDE: Works OOB (SouthBridge SiliconImage Driver from DVD used)
- ATI Sapphire 3870 works (if you find the right combination of drivers to install from the DVD...)
|
EFI w/ Vanilla Kernel WORKS
|
SiliconImage3132.kext has some ownership problems. chmod/chown + reboot makes the pain go away.
|
| IC7-G
|
Intel 875PE
|
- Install Method: Kalyway 10.5.1 with 10.5.2 KalywayComboUpdate
- BIOS Version: 28; Revision: Unknown
- Audio: Works OOB
- LAN: Works OOB, no auto-detect at starup, need to disconnect and reconnect to work
- SATA & IDE: Works OOB
|
Unknown
|
LAN has auto-connect problems
|
| IP35 Pro
|
Intel P35 + ICH9R Chipset
|
- Install method: Kalyway 10.5.1 or Retail Mac OS X Server 10.5 DVD w/ PC-EFI & Combo Updater
- Kalyway:
- Install options: Formatted GUID, EFIv8 + Vanilla Kernel
- Updated to 10.5.2 using Kalyway Intel combo update + Kalyway 10.5.2 kernel
- Leopard Graphics Update v1.0 worked with no hassle
- Bios version: 1.4, Rev. unknown
- Bios setup: SATA set to AHCI; EIST: enabled, Disable bit: enabled
- Audio works with: AppleHDAPatcher v1.20 + ncx5 ALC888 dump
- SATA works as AHCI
- IDE status: unknown
- LAN works out of the box
- Firewire works out of the box
- Mac OS X Server:
- BIOS Version: 14
- Audio: Realtek ALC888 HD, AppleHDA patch
- LAN: 2x OnBoard Gigabit LAN, no patch (can't remember controller-name)
- SATA & IDE: 6 Built-In S-ATA ports in AHCI, 2 eSATA ports in AHCI (JMicron), 1 IDE port (JMicron), and 1 floppy port (JMicron). All working.
|
EFIv8 + Vanilla kernel
|
No; Audio needs patching
|
| IP35-E
|
Intel P35
|
- Install Method: Kalyway 10.5.1 & Apple 10.5.2 Update
- BIOS Version: 15; Revision: Unknown
- Audio: Need patch from here
- LAN: Works OOB
- SATA & IDE: SATA works OOB, IDE works after install
- Optical Drive: Which one? Any weird problems with installation?
- Shutdown / reboot works only with 10.5.1 - needs custom kernel for 10.5.2, Sleep not tested
|
Vanilla & EFI works
|
Audio needs patching
|
| IX38 Roadster
|
Intel X38 + ICH9R Chipset
|
- Install Method: BrazilMAC 10.5.0 (Updated to 10.5.2 using Kalyway Intel combo update)
- BIOS Version: 12
- Audio works with: AppleHDAPatcher v1.20 + ncx5 ALC888 dump
- LAN: Works Native
- SATA & IDE: SATA works in AHCI mode. Does not work in RAID mode.
- Firewire works out of the box
|
EFI/Vanilla kernel: Not Tested
|
No, audio needs patching.
|
| LG-95
|
Intel 945GC + ICH7
|
- BIOS version: 10, Rev. 1.0
- Installation (10.5.0) method: BrazilMAC method with EFI 8.0 on GPT using iGuru guide
- Update to 10.5.2: Netkas method
- Audio (ALC 888): Works with skippyretard patch
- Video (GMA 950): Works with modified AppleIntelIntegratedFramebuffer.kext from BrazilMAC guide
- LAN: Works out of the box
- IDE and SATA: Works out of the box
- ACPI: Sleep/Wake/Restart work (Shutdown works half of time)
|
Yes
|
No, audio and video need patching
|
| LG-95
|
Intel 945GC + ICH7
|
- BIOS version: 14
- Installation method: Leo4all v2 (10.5.2) with Vanilla Kernel 9.2.2
- Audio (ALC 883): 2ch only so far. Works with Azalia patch from skippyretard. Tried the 883 kexts from Leo4all v2 install, latest Taruga's 5.1 kext (April 24th, 2008) and skippyretard's 883 pkg with no luck. Linux reconizes ALC883 OK. Maybe the guy up here with an ALC888 has a different mobo revision.
- Video (GMA 950): Works with GMA950 driver from the Leo4all install DVD. QE/CI enabled and no artifacts. Resolution fixed at 1024x768, I changed it editing com.apple.Boot.plist adding <string>"Graphics Mode"="[email protected]"</string>. There is some minor mouse blinking when moving over the dock, hardly noticeable.
- LAN: Works out of the box
- IDE and SATA: Works out of the box
- ACPI: Restart & Shutdown works fine so far.
- PROs: Very cheap and compatible.
- CONs: NOT an overclocker motherboard, FSB is locked in the Bios.
|
Yes
|
No, audio needs patching
|
| Fatal1ty F190-HD
|
ATi Radeon Xpress 1250
|
- Install Method: Kalyway 10.5.1 - 10.5.2 Kalyway Combo Update
- BIOS Version: Modded from Abit Forum; Revision: 17
- Audio: Realtek ALC888, Download Installer Here
- LAN: Works OOB
- SATA & IDE: IDE and SATA full Function OOB however you must use SATA channels in order i.e. miss something plugged in on the first sata channel and the installer will not find anything in channels 2, 3 and 4 and you will get 'IOATAStorage controller' blocking Bus error in verbose mode.
- Optical Drive: LG Sata DVD-RW/RAM drive no problems
- Shutdown works, restart doesn't, Unsure about sleep.
- There is no support currently for the x1250 integrated graphics.
- PRO:'s Cheap Mobo good features looks amazing and is M-Atx. Overclocks well.
- CON:'s No integrated Graphics but I am using an ATi 3850 HD Card with full QE/CI so no real loss overall its a great little board!
|
Yes
|
No audio needs patching and onboard graphics don't allow resolution change or QE/CI due to no graphic kext.
|
| Fatal1ty FP-1N SLI (maybe FP-IN9? there is no "1N")
|
|
- Install method: Kalyway 10.5.2 to a Primary SATA Partition, partitioned through Diskpart in Vista to AF.
- Bios: 14 with SLIC table Patch (this shouldn't matter)
- Audio: Works OOB, with Jack Sensing working well
- USB: Seems to work well. Logitech USB headset works perfectly OOB
- LAN: OOB
- All power functions work OOB
- RAM: All 4GB working perfectly. Loving my 4Gb Mac
|
Yes
|
All good
|
| I-45C
|
|
- Install method: Kalyway 10.5.2 to a Primary IDE Disk
- Audio: Works OOB
- USB: Seems to work well. USB keys/HDD OK. Logitech Webcam OK with macam.
- IDE : OK
- SATA : not tested
- LAN: Works OOB (Marvell kext included in Kalyway 10.5.2)
- Video : Works OOB
- Power functions not tested
- RAM: All 4GB working perfectly.
- Price : 40 Euros !!! ;-)
|
Unknown
|
All good
|
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . .
| Hardware Name
|
Chipset
|
Notes
|
EFI/Vanilla kernel working
|
Fully Working w/o Patch
|
| Conroe-1333 D667
|
Intel 945GC
|
- Install Method: Kalyway 10.5.1 + Devin 10.5.2 Update method
- BIOS Version: 1.3; Revision: Unknown
- BIOS Options: HPET "Enabled", Execute bit "disabled", Suspend to ram "Auto"
- Audio: Need ALC888 patch but no input
- LAN: Works OOB
- SATA & IDE: Works OOB
|
PC-EFI & Vanilla Kernel work
|
Audio needs patch
|
| Asrock Conroe 1333
|
Intel 945GC & ICH7 Chipset
|
- Install method: Kalyway 10.5.1 or Kalyway 10.5.2
- Install options: Vanilla Kernel, BOOT_efi_mbr
- Updated to 10.5.2 using the original Apple combo update using Devin's procedure on insanelymac [1]
- Updated to 10.5.3 using Kalyway 10.5.3 combo update (had to reinstall discrete nVidia card driver afterward through NVinstaller to get Display Resolution change and QE/CI working again)
- Updated to 10.5.4 using the original Apple update tool without any problems
- Leopard Graphics Update v1.0 normal install, works
- Bios version: P 1.30 (no other firmware later than 1.30 works -tested up to 2.10-)
- SATA + PATA works
- Onboard LAN work
- Audio works with alc_out (2ch out only)
|
YES
|
Audio needs patching
|
| Conroe 1333
|
Intel 945GC
|
- Install Method: Kalyway 10.5.1 & Update to 10.5.2 following Netkas's guide
- BIOS Version: P1.30; Revision: 1.0
- BIOS Options: CPUMAXID set to disbled
- Audio: ALC888, AFAIK only Azalia 2.1 output
- LAN: Works OOB
- SATA & IDE: Both work OOB
|
PC-EFI v8 & Vanilla Kernel work
|
No, Audio needs patching
|
| 4CoreDual SATA
|
VIA Apollo PT880Pro/PT894
|
- Install Method: Kalyway 10.5.1 & Kalyway Combo Updater
- BIOS Version: 1.9; Revision: 1
- Audio: Works OOB
- LAN: ViaRhineIl works with Stevo4 Patch
- SATA & IDE: Both work OOB (may need to append SATA ID 0x73721106 into AppleVIAATA.kext for SATA to work on SATA2 board)
|
PC-EFI works
|
LAN needs patching
|
| Asrock 939 Dual-VSTA
|
Northbridge: ULi M1695 Southbridge: ULi M1567
|
- Install Method: Zephyroth AMD 10.5.2 Rev.1
- Options: 9.2 kernel
- Audio: unknown, using usb sound card
- LAN: Onboard Not Recognized, using realtek card
- SATA & IDE: use this kext for full speed
- No PS/2
|
unknown
|
Onboard audio, lan and ps/2 need patching
|
| Asrock 939Dual-SATA2
|
Northbridge: ULi M1695 Southbridge: ULi M1567
|
- Install Method: Zephyroth AMD 10.5.2 Rev.2
- Options: 9.2 kernel
- Audio: ACL850 (not working)
- LAN: ULI- Onboard Working
- SATA & IDE (SATA only working from II slot)
|
unknown
|
Onboard audio, lan (lan works after install until first reboot then breaks) need patching
|
| ASrock ALIVE NF6G-VSTA
|
NForce 4 (MCP61)
|
|
- EFI: Yes
- Vanilla Kernel: No (AMD CPU)
|
- Audio, SATA and Network need patching (IDE is slow without the patch)
|
| P4i65G
|
Intel 865G (North) & ICH5 (South)
|
- Install Method: Leo4Allv2 10.5.2
- BIOS Options: Default options.
- Audio: Need AC97 patch
- LAN: Not Tested
- SATA & IDE: IDE works fine, SATA not tested.
- Also applied ICHx patch and used legacy APCI
|
PC-EFI works, no vanilla kernel.
|
Audio needs patch
|
| Conroe-1333 D667 Rev. A/G 1.03
|
Intel 945GC
|
- Install Method: Kalyway 10.5.2
- Modified BIOS Version: 1.80; It's nice to have BIOS 1.80 because it supports latest CPUs
- BIOS Options: Default Options
- Audio: Works without Patches (Except Input)
- LAN: Works OOB
- SATA & IDE: Works OOB
- You can find the Moded BIOS here[2]
|
PC-EFI & Vanilla Kernel work
|
Everything Works Without Patching. Credits go to Kabyl (InsanelyMac) He made the moded BIOS.
|
| 4CoreDual-SATA2 (R1.0][3]
|
Northbridge: VIA® PT880 Pro/PT880 Ultra - Southbridge: VIA® VT8237S
|
- Install Method: Kalyway 10.5.1 w/TheStevo4 ppf + Kalyway 10.5.2 Update
- BIOS Version: 1.9 (latest)
- BIOS Options: USB Legacy support enabled, Suspend to ram "Auto"
- Audio: ALC888 in & out stereo working (7.1 not tested)
- LAN: VIA PHY VT6103 not yet tested but should work.
- IDE: Works, SATA: not yet tested
|
PC-EFI works, NO Vanilla Kernel (VIA Chipset)
|
Stevo4 patches (see ASRock wiki page)
|
| ConRoe945G-DVI
|
Intel 945G + ICH7
|
- Install Method: Kalyway 10.5.2 SleepKernel EFI8 MBR
- BIOS Version: v1.90
- Audio (ALC888): 2Ch Out Works with AppleAzaliaAudio and KEXT-Edit
- LAN (R8111B): Works
- SATA & IDE: Works
- Video (GMA 950): Works
|
EFI v8 Works
|
Audio Needs patching
|
| ALiveXFire-eSATA2
|
Northbridge: ATI CrossFire Xpress 1600 (RD480)
Southbridge: ATI SB600
|
- Install Method: Zephyroth AMD 10.5.2 Rev.1
- BIOS Version: 2.60+; Revision: Unknown
- BIOS Options: If you want to install on a SATA drive, make sure in the IDE menu, "AHCI" is chosen rather than "Non-Raid" otherwise you may get errors
- LAN: Works OOB
- SATA & IDE: Works OOB
|
unknown
|
Audio may need patching
|
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
| Hardware Name
|
Chipset
|
Notes
|
EFI/Vanilla kernel working
|
Fully Working w/o Patch
|
| Rampage Formula
|
Intel X48 + ICH9R
|
- Install Method: Kalyway 10.5.2
- BIOS Version: 0308
- Audio: Works OOB using AppleHDA driver but no input and SPDIF output, or, use Speaker, Mic and Digital Out works
- LAN: works OOB
- SATA: works OOB
- Intel PATA: works OOB
- JMicron PATA: OOB (Except DVD)
- USB: all working
- Firewire: Not Tested
- Install from SATA Optical drive / USB DVD work, install from JMicron IDE optical drive doesn't
|
EFI + Vanilla / Kabylkernel / 9.2 sleep
|
yes, update to 10.5.3 using kalyway combo update, 10.5.4 through apple update (shut down only work properly with 9.2 sleep kernel)
|
| Maximus Formula
|
Intel X38 + ICH9R
|
- Install Method: Kalyway 10.5.2
- BIOS Version: 1201
- Audio: Speaker and Digital Out works (sometimes have some minor issues)
- LAN: OOB
- SATA & IDE: OOB
- JMicron PATA: OOB
- USB: OOB (May not recognize all USB ports)
- Firewire: integrated VIA VT6308 works but crappy... buy a firewire pci card with VT6306
- Had keyboard error with USB/PS2 adapter, no error using PS2 directly
- Install from dvd sata otherwise "still waiting for root device"
- USB DVD Installation works also
- Updating to 10.5.3 using "software update" does NOT work
- Shutdown does not work properly, fans keep rotating
|
EfI & Vanilla Kernel
|
yes, except audio
|
| P5E
|
Intel X38 + ICH9R
|
- Install Method: Kalyway 10.5.1 - Install Info Below
- BIOS Version: 303; Revision: Unknown
- Audio: Audio Out works OOB, In doesn't work
- LAN: Works OOB
- SATA & IDE: Both work OOB
- Optical Drive: Which one? Any weird problems with installation?
- Do shutdown, reboot and sleep work?
- Installation Instructions:
- Combo Update (No Reboot)
- Kernel Update (No Reboot)
- Repair Permissions
- Reboot
- Apple Graphics Update (No Reboot)
- New Natit Driver
- Repair Permissions
- Reboot
|
EFI v8 & Vanilla Kernel
|
Yes
|
| P5W DH Deluxe
|
Intel 975X + ICH7R
|
- Install Method: Kalyway 10.5.1/10.5.2
- BIOS Version: 2602; Revision: 1.04G
- Audio: Realtek ALC882M works
- LAN: Marvell 88E8053 both ports work out of box
- SATA: all port works, ICH7R IDE works, Jmicron IDE work
- Onboard WiFi work with realtek 8187 drivers but unstable|
- Onboard FireWire: Both ports (1 backpanel and 1 in case) work OK.
- ez_raid ports work out of the box, natively. Raid0 works natively.
|
Yes
|
With appropriate drivers selected in kalyway 10.5.2, everything work right out of the box except onboard wifi needs patching
|
| P5K Deluxe WiFi
|
Intel P35 + ICH9R
|
- Install Method: Kalyway 10.5.2, updated to 10.5.3 with Kalyway combo 10.5.3 update
- BIOS Version: 812; Revision: Unknwon
- Audio: Internal AD1988B only stereo out WORKS OUT OF BOX, audio in: works after patching with Taruga AD1988B rev3 Installer. but require to reinstall video.
- LAN1: Realtek, not tested, Shut off in bios WORKS OUT OF BOX, required to be ON in BIOS for Time machine to work
- LAN2: Marvel Yukon on internal PCIe bus fully works WORKS OUT OF BOX
- WLAN: Does not work, but there exists a patch to get it working
- SATA & IDE: Both SATA controllers fully work, IDE CD-ROMs and DVD-RW work
|
EFI & Vanilla Kernel Work
|
YES
|
| Asus P5K-E WiFi/AP
|
Intel P35 + ICH9R
|
- WORKS OUT OF THE BOX:
- ICH9 6x Sata ports
- Jmicron 2x E-Sata ports
- Firewire, USB, COM1
- WORKS AFTER PATCHING:
- Audio=ad1988b fully working (stereo, 5.1 digital output, microphone,volume control) using taruga's drivers: http://wiki.taruga.net/tiki-index.php
- Lan=marvel88e8056
- Wifi=realtek 8187l, configured as ethernet and uses Realtek app.
- Leopard WIFI drivers now available here!
- WORKS FOR SOME/GIVES SYSTEM CRASHES
- IDE/PATA ports work for me, <- "which driver do you use, btw do you also have 4gb ram?"
- BIOS SETTINGS (Update to latest 1004 or 1006):
- Set HDD-controllers 'ich9/jmicron' to AHCI mode, powerstate=S3
- Processor: Enable apic2.0, disable speedstep, disable c1e, enable VT and XT
- 4gb ram working < dependent on BIOS settings, read the forum if you have kernel panic!!!
- Install method easy:
- Kalyway 10.5.1 Install DVD 'select right patches, try MBR if GUID fails'
- Updated to 10.5.2 using Kalyway ComboUpdate and kernel update.
- Updated to 10.5.4 using software update (vanilla 9.4 kernel works great, sleep works, everything works :D)
- iATkOS users use this thread
- Install method advanced:
- Retail-Leopard-DVD, GUID, pc-efi8, with retail kexts 'remove appleintelcpupowermanagment.kext, add dsmos.kext', only AUDIO/LAN/VIDEO.kexts needs to be added after that, also may add applesmbios.kext for showing right info in system profiler.
- Retail-Leopard 10.5.2 + graphics update also work. see netkas.org for howto
|
YES
|
On DVD (Kalyway) or patch (iAtkos)
|
| P5KC
|
Intel P35 & ICH9
|
- Install Method: Kalyway 10.5.1 and 10.5.2 Combo Updater
- BIOS Version: 2602 or 0903; Revision: Unknown
- Audio: ACL883 Tarugas patch or ALC883 driver on install DVD
- SATA & IDE: SATA works, IDE not tested
- LAN doesn't work.
- Onboard WiFi works
- For some people, install the new kernel before the update
|
EFI & Vanilla Kernel
|
No. LAN doesn't work
|
| P5K
|
Intel P35 + ICH9
|
- Install Method: Kalway 10.5.1 - upgraded to 10.5.2
- BIOS Version: Unknown; Revision: Unknown
- Audio: Using onboard with ALC883 installer
- LAN works with this driver (maybe hangs after sleep)
- SATA & IDE: SATA works, in AHCI Mode
Stable having flashed P5KR bios 403 on P5K using AFUDOS /N to force ICH9 into AHCI mode
Now running for week stable with MAXMEM = 3072 in boot.plist, kept crashing without this option with 4GIG of RAM
|
EFI & Vanilla Kernel
|
Audio and LAN need patching
|
| P5K PRO
|
Intel P35 + ICH9R
|
- Install Method: Leo4all v.3 and Kalyway 10.5.3 combo update
- BIOS Version:0806 BIOS setting: no changes needed, standard
- Audio: Realtek ALC883 - functional with 883 driver and patched kernel
- LAN: Marvell 88E8056 - functional using SKGE driver
- SATA & IDE: This board uses Marvell IDE driver, so you need to instal both drivers for Intel ICHx chipsets and "VIA Sis Marvell and SB chipset driver".
- Optical Drive: LG multi format drive on IDE, no problem
- USB - works OOB
- Do shutdown, reboot and sleep work? With Vanilla kernel yes, with patched kernel no. But Vanilla has problem with Core 2 Quad processor.
-
|
Yes
|
Almost everything works OOB, with patched kernel does not work power management.
|
| P5K SE
|
Intel P35 + ICH9
|
- Install Method: Kalyway 10.5.2 and 10.5.3 Combo Updater
- BIOS: 1008, standard settings
- CPU: manual overclocking possible (45 nm CPU tested)
- Audio: select alc883 kext during install (only tested analog stereo line-out, line-in an mic in: works).
- LAN: Onboard LAN requires installation of the DaemonES/MadInt driver/package. If you put your computer to sleep, onboard LAN stops working at wake up. It works again after rebooting.
- PCI-card Realtek RTL8169 works out of box; D-Link DGE530T 1GigE with skge-e.kext (Driver from D-Link website doesn't work).
- SATA: SATA works alright out of the box (as long as you don't enable SATA RAID).
- IDE (and possibly E-SATA) - Marvell chip 88SE61xx - needs patching: Marvell and others ATA kext for Leopard, by podarok - works after patch but crashes sometimes during trys to burn a DVD with Toast.
- USB: Works without problems
- USB Booting: Functional, at least after installing with internal SATA connection. Bear in mind that your system may lock up if power settings are configured to turn the HDD off after a certain period of inactivity.
- Optical Drive: IDE, SATA, and USB Optical Drives are supported.
- Graphics: Point of View Nvidia 8800GTS with nvinstaller 0.33 - 1920x1200 with full Quarts Extreme and Core Image support (QE/CI). -- Had to replace old Nvidia 6800GT because QE/CI acceleration wouldn't work in Leopard. -- Asus 7300 GT (256 MB) and XFX 8600 GT work with nVidia kext selected during installation.
|
Yes
|
No: both onboard LAN and IDE require patching.
|
| Asus P5B SE
|
Intel P965+ICH8
|
- Install Method: Kalyway 10.5.2
- BIOS Version: 0302
- Audio: Onboard, AzaliaAudio.pkg only 2ch stereo is working
- LAN: Onboard, Attansic L1 Ethernet
- SATA & IDE: SATA works, IDE not testd, can't add another drive
- Optical Drive: HP1070, work out of the box. Originally tried to install with an old ide dvd drive. had to use a SATA
- shutdown does not shutdown completely. restart works, sleep not tested
- firewire pci card works out of the box
|
BOOT.EFI.V80
|
|
| P5B Deluxe
|
Intel P965 + ICH8R
|
- Install Method: Kalyway 10.5.1, Upgrade: Kalyway_Hack_10.5.2ComboUpdate
- ComboUpdate method, be prepared for several lengthy reboots. Relax & just let it run.
- P5B Deluxe BIOS Ver.1226
- Audio: AD1988B 8-channel High Definition Audio still not working after update (patches not tested)
- JMicron JMB363 SATA / PATA controller NOT TESTED (2 x External SATA 3.0 Gb/s ports)
- Intel Matrix Storage Technology (RAID) controller not recognized by OS X
- All six (6) SATA 3.0 Gb/s internal ports tested working in ACHI (after upgrade)
- IDE mode NOT TESTED
- Marvell Gigabit LAN Port 1 working; Port 2 still not working (patch not tested)
- All ten (10) USB 2.0 ports working
- All PCI Slots working
- Both (2) FireWire ports working (TI 1394a controller)
- Partitioned as MBR using EFI bootloader
- TimeMachine working
- Software RAID drives created w/ DiskUtility still working fine after upgrade
|
EFI v8 + Vanilla Kernel
|
No; Onboard Audio and LAN port 2 need patches
|
| P5B-E Plus
|
Intel P965 + ICH8R
|
- Install Method: Kalyway 10.5.2
- BIOS Ver. 0627/0633
- Audio: AD1988B 8-channel HD Audio only in Stereo (default patches in Kalyway custom install; BIOS: Advanced > Onboard Devices Configuration > Front Panel Support Type "AC97")
- Internal SATA (x6) ports working in ACHI and RAID
- JMicron JMB363 SATA in AHCI (not PATA)
- IDE mode not tested
- Marvell Gigabit LAN Port working (default patches in Kalyway custom install)
- USB 2.0 ports working (BIOS: Advanced > USB Configuration > Bios EHCI Hands-off "disabled")
- FireWire (kernel/System.kext versions must match)
- Partitioned as MBR with EFI v.8; GUID works as well
- TimeMachine works
- Note: Does not wake up from sleep.
|
MBR + EFI + Vanilla Kernel, GUID + Kabyl
|
Not quite, but close; Onboard 7.1 Audio only in stereo
|
| P5B PLUS
|
Intel P965 + ICH8
|
- Install method: Kalyway 1.5.1 + Kalyway Combo update
- Onboard audio: Working (With Kalyway audio patch)
- Onboard LAN: not Working
- Sata: full working
- IDE: Works after Install. For boot Sata drive needed.
- Video: Working with Kalyway Nvinject.
|
EFI v8 working. Vanilla 9.2.0 working.
|
Audio needs Azalia patch
|
| P5GC-MX
|
Intel P965 + ICH8
|
- HD fresh install with GUID using Disc Utility
- iATKOS v1.0i SSE3 with vanilla kernel 10.5.1
- Used PC_EFIv8 for GUID booting
- Updated to 10.5.2 using the original Apple combo update but using Devil's procedure on insanelymac
- Onboard LAN doesn't work
- Audio works with HDAPatcher ALC883.
|
YES
|
Audio needs patching
|
| P5B
|
Intel P965 + ICH8
|
- Install Method: Kalyway 10.5.1, ComboUpdate + Kernel Patches applied in 10.5.1 or "Onetracks perfect install" works with ToH RC2 which is a lot of work
- BIOS: Unknown
- Audio: works after upgrade, needs patch in 10.5.1
- Storage: ACHI working; Install from IDE not working, install to IDE unknown
- LAN: Working
- Partitioned as MBR using EFI bootloader
- Onetrack:
- Audio: Needs editing or patching AppleAzaliaAudio.Kext, audio in not supported
- LAN: Works OOB
- SATA & IDE: Works OOB (JMicron IDE works OTB with Kalyways install Disc, otherwise JmicronATA.kext needs editing)
|
EFI & Vanilla Kernel
|
No, Patches applied in 10.5.1
|
| P5E-VM DO
|
Intel Q35 + ICH9DO
|
- Install Method: Kalyeay Leopard 10.5.1, manual Update 10.5.2 kalyway combo update,
- BIOS revision: latest, BIOS settings for stock/vanilla kernel with sleep mode bit problem])
- Audio: Realtek® ALC883, 8-channel High-Definition Audio CODEC: works out of the box, some problem after 10.5.2
- LAN: Intel® 82566DM PCIe Gigabit LAN controller: not work patch unavailable
- SATA: works out of the box
- IDE: no test
- onboard USB to front:works out of the box
- onboard USB to back: works out of the box
- onboard Intel® Graphics Media Accelerator 3100 (Intel® GMA 3100) integrated: bypass by PEAK Geforce 7300 GT: work whit Vinject :-) )
|
no kernel vanilla patch apply and works well
|
95% working out of the box, some problem with network card intel pro 100 autodisconnect after computer stanby.U sb device storage auto unmount. Running stable in the end!
|
| P5E-VM HDMI
|
Intel G35 & ICH9R
|
- Install Method: Kalway 10.5.2
- BIOS Version: 0506
- Onboard Audio works - ALC 883 (S/PDIF not tested yet)
- Onboard Firewire works - VIA VT6308P
- Onboard Video (x3500) works but not accelerated VESA 3.0
- Onboard SATA works, PATA not tested
- HDMI Output not tested yet
- Onboard LAN does not work - Atheros L1 PCI-E Gigabit
- Onboard RAID not tested yet
- Shutdown and Reboot works perfectly, Sleep does not work
- Startup welcome movie not played but there is sound on first boot
- Used Vanila Kernel
|
EFI working
|
Everything but LAN is working
|
| P5K-VM
|
Intel G33 + ICH9
|
- Install Method: Kalyway 10.5.2, manual 10.5.3 Kalyway combo update (works),
- BIOS 803: latest, BIOS settings standard
- CPU: Overclocking no problem (Wolfdale)
- RAM: 8 GB (4 x 2 GB) DDR2 800 MHz recognized
- Audio: Realtek® ALC883, 8-channel High-Definition Audio CODEC: analogue works out of the box (selected during install, only stereo tested)
- LAN: Marvell88E8056® PCI-E Gigabit LAN controller: works out of box
- SATA: All 4 ports work out of the box
- IDE: JMicron® JMB368 works out of the box
- USB: works out of the box
- Firewire: works out of the box
- onboard Intel® Graphics Media Accelerator 3100 works but: bypassed by Asus 7300 GT 256 MB: works (nVidia kext selected during install)
|
Yes
|
near 100% working out of the box, sometimes does not completely shut down
|
| P5KPL-VM
|
Intel G31 + ICH7
|
- Install Method: Kalyway 10.5.1, Combo Updater, Netkas method
- Bios release: 303
- Audio work
- LAN Attansic/Atheros L1 work with DaemonES/MadInt driver
- GMA3100 Don't work yet
- NV7600GT 256MB (with nvinject)
- System Profiler unstable (Need patch from 10.4.10)
|
PC_EFI_V8 + Grub, Vanilla Kernel
|
No
|
| P5WD2 Premium
|
Intel 955X + ICH7R
|
- Install Method: ToH 10.5 > Apple combo 10.5.1 + ToH 10.5.1 kernel > Apple combo 10.5.2 via this guide + ToH 10.5.2 kernel
- BIOS Version: 0802 (latest available); Revision: beta
- Audio: Realtek ALC882 - works with Taruga 1.2 patch
- LAN: Intel PCIe Gigabit LAN Controller (integrated) - works OTB; Marvell 88E8001 Gigabit LAN Controller (integrated) - turned off & not tested
- FireWire: Texas Instruments 1394a controller (integrated) - works OTB
- IDE: works OTB; ITE IDE controller (integrated) - turned off & not tested
- SATA: works OTB; Silicon Image 3132 SATA controller (integrated) - turned off & not tested
- Asus WiFi-TV PCI card (optional) - not work
|
EFI v8 works
|
Audio needs patching
|
| P5B-MX
|
Intel 946GZ + ICH7
|
- Install Method: Kalyway 10.5.2
- BIOS Version:; Revision:
- Audio: Audio works with AZALIA
- LAN: Not tested
- SATA & IDE: IDE works, SATA not tested
- Requires MBR
|
EFI & Vanilla Kernel
|
Audio needs patching
|
| P5GC-MX/1333
|
Intel 945GC + ICH7
|
- Upgraded from Kalyway 10.5.1 to 10.5.2 using /"kalyway_hack_10.5.2ComboUpdate/"
- Onboard LAN doesn't work
- PS2 mouse an Keyboard: works out of the box
- SATA: works out of the box
- IDE: works out of the box
- onboard USB works out of the box
- Power off, sleep: work
- Audio works with HDAPatcher ALC883.
|
YES
|
Audio needs patching
|
| P5LD2-VM DH
|
Intel 945G + ICH7
|
|
Netkas' PC EFI V8 required to use vanilla/stock kernels
|
99% working out of the box, besides audio (see left). Running very stable in the end!
|
| P5LD2-VM SE
|
Intel® 945G + ICH7
|
- Install Method: Retail DVD & web update to 10.5.2(Netkas Method)
- BIOS Version: 0602
- Audio ALC 882: Works with patch
- LAN: Works out of the box
- SATA & IDE: Works out of the box
|
PC-EFI-V8 + Vanilla Kernel work
|
Audio needs Patching, and couple of kext removed/replaced.
|
| P5AD2-E Premium
|
Intel 925XE
|
- Install Method: Kalway 10.5.1
- Audio: Onboard via Azalia Out
- LAN: Works, WiFi untested
- SATA & IDE: SATA works, IDE unknown
|
Kalyway 10.5.1+ 10.5.2 upgrade
|
|
| P5GPL-X SE
|
Intel 915PL + ICH6
|
- Install method: Kalyway 10.5.1, Kalyway 10.5.2 Combo Updater & Kernel Patch
- BIOS Version: 0301
- Audio: ADI1986A - use AppleAzaliaAudio.kext from JaS 10.4.8 DVD (Kalyway 10.5.1 version did not work)
- LAN: Marvell Yukon 88E8001 - use Marvell Yukon 88E8001 driver
- SATA & IDE - both work by default
|
PC EFI (MBR) works, Vanilla Kernel does not
|
No, LAN and Audio Output need patching
|
| Striker II Formula
|
NVIDIA nForce 780i SLI
|
- Install Method: Kalyway 10.5.2
- Bios Version: 1303 (2008/05/16)
- Audio: 2 Speaker,Digital Out and Mic Works (AD1988b_rev3_Installer)
- Lan: not working
- SATA & IDE: works
- FireWire: works
|
EFI v8 Works
|
No, overall system is too unstable
|
| Striker Extreme
|
NVIDIA nForce 680i SLI
|
- Install Method: Kalyway Update combo 10.5.2 + 10.5.2 SSE3 kernel update to fix boot delay and black screen, efi MBR
- BIOS Version:1401
- Audio: SoundMax AD 1988B, working stereo only, no input with AzaliaAudio.pkg installer
- LAN: Marvell Yukon 88E8039, working with nforcedeath, both nics, all CPUs enabled, unstable under load
- SATA & IDE: Does SATA work? Both working flawlessly out of the box (10.5.1 and 10.5.2)
- Optical Drive: Both IDE and SATA drives working. Both optical drives LiteOn models DVD burners
- Shutdown, reboot work flawlessly, sleep hangs computer after update to 10.5.2
- Video card GeForce 7600GT working Quartz Extreme with latest nvinject 0.2.1 had to edit NVDAResman.kext,NVDANV40.HAL,NVDANV30.HAL with device specific ID and remove all other device ID's
|
Not tested
|
LAN and Audio
|
| P5N32-E SLI Plus
|
NVidia nForce 680i SLI
|
- Install Method: Kalyway 10.5.2 and 10.5.3 Combo Update Package by Mysticus v1.3
- CPU: Core 2 Quad Q6600 had to edit about this mac strings file to show that in the about this mac window
- Audio: didn't test since I'm using sound blaster audigy 2 zs pci card and that didn't work either
- LAN: Onboard LAN requires installation of the forcedeth driver
- still doesn't work though, shows as always being unplugged
- used a D-Link DFE-530TX+ PCI Adapter and that worked fine
- SATA: SATA works alright out of the box (as long as you don't enable SATA RAID) but freezes sometimes
- suspects it's because the nforce drivers are still buggy
- IDE: works
- USB 1 and 2: works but not able to mount usb drives until after you install the 10.5.3 combo update, don't select PCUSBGen fix, not needed
- USB Booting: not sure
- Optical Drive: SATA and USB Optical Drives are supported after 10.5.3 combo update installed
- Graphics: Nvidia 8600GTS 256 MB with nvinject 256 option selected with full Quarts Extreme and Core Image support (QE/CI)
|
No: select nforce kernel 9.2.0 following guide posted with efi enabled and when using combo update of 10.5.3
|
No
|
| Crosshair AM2
|
NVIDIA nFocre 590 SLI MCP55
|
- Install Method: Zephroth AMD SSE3 9.2.0 Kernel
- BIOS Version: 0702; Revision: Unknown
- Audio: Works with AzailiaHD from install DVD
- LAN: Doesn't Work - OSX detects them with Forcedeth and they have MAC addresses however they will not detect Ethernet cables
- SATA & IDE: Both Work
- To avoid "Still Waiting for root device," have an IDE HD and optical drive plugged in and install on SATA
- Needs boot hang fix if using GUID - same as Asus A8N-E NFORCE4
|
EFI v8 Works
|
LAN doesn't work, Audio needs patching (reinstall AzailiaHD after 1st boot)
|
| M2N-E
|
NVIDIA nForce 570 Ultra MCP
|
- Install Method: LEO4ALL v3 10.5.2 AMD SSE3 9.2.2 Kernel .
- BIOS Version: 1202; Revision: Unknown.
- Audio: ADI 1988 HD Audio Device; works with Azalia driver installed from dvd.
- LAN: Not tested.
- SATA & IDE: SATA works with Nforce Test driver from dvd; IDE Not tested.
|
EFI Worked.
|
No, audio,sata needs patching,slow boot (aprox. 3-4 minutes) .
|
| M2N32-SLI Deluxe
|
Nforce 590 SLI MCP
|
- Install Method: Leo4All-10.5.2 PPFv1 Universal AMD/INTELSSE2/SSE3 9.2.0 Kernel
- BIOS Version: 1802; Revision: Unknown
- Audio: ADI AD1988B SoundMAX, Azaila Driver From DVD
- LAN: Realtek RTL8187 Wireless 802.11b/g 54Mbps USB 2.0e (Integrated), RTL8187 Driver From DVD
- SATA & IDE: It Will Install On IDE or SATA
- Optical Drive: SATA LG DVD Burner | Had to hook up IDE DVD-Rom to install (removed IDE Rom after install and everything works fine)
- AMD-Patch From DVD
|
EFI Worked
|
The integrated LAN does not work out of the box. (Did not try to fix this, because on board wireless worked with patches applied during install. No post-install patches applied.
|
| M2N-E SLI
|
NVIDIA nForce 500 SLI MCP
|
- Install Method: Zephyroth 10.5.2 AMD SSE3 9.2.0 Kernel
- BIOS Version: 0902; Revision: Unknown
- Audio: C-Media 6501 HD Audio Device; works out of the box, recognised as USB Audio Device
- LAN: Works with nForce 2/3/4/5 drivers selected in install options.
- SATA & IDE: SATA works (can do flat install to SATA HDD); IDE Works
|
EFI v8 Works
|
No, lan needs patching
|
| A8N-SLI
|
NVIDIA nForce4 SLI
|
- Install Method: Zephyroth 10.5.2
- BIOS Version: 1604; Revision: Beta
- Audio: Realtek ALC850 (Selected AC'97 from Customize list)
- LAN: nForce4 built-in Gbit MAC (Selected forcedeth from Customize list)
- SATA & IDE: Installed OS onto IDE drive without problems. Also have two SATA drives in Striped RAID configured through MediaShield ROM, but the RAID showed up as two individual drives in Mac's Disk Utility during installation. Cannot access RAID even after installation.
- Optical Drive: BenQ DW1625. During the 15 odd times I booted from the DVD to install, after the first 6 or 7 times, the installer started saying that it could not read from the disc. This was happening when it normally would check the media for errors. So, I re-burned a new disc using the same drive of the same ISO(which I had initially created from the original (now problematic) disk). The new disc worked. Maybe, just a very fragile disc. But, weird.
- Shutdown and reboot works. Sleep gives a blank (black), unresponsive screen. Have to hard reset.
- Had to run the installation, with the same options, multiple times for it to get it right. After a few installs, I was getting the gray screen asking me to restart the computer. I really don't know how I got around that problem. I just installed again without changing any options. Finally, when it worked, I had my ethernet cable unplugged. In the Customize list, I had chosen the nforce chipset 2/3/4/5 kext, AC '97, forcedeth, nvidia geforce 10.5.2 and nvinject 128 MB for my 6600GT graphics card. Name of volume: Leopard. I chose the EFI v8 plus MBR bootloader to make the "Leopard" volume bootable. I'm using grub to choose between my various OSes. SSE3 9.2.0 TOH Kernel chosen from the Customize list.
- Can only install from same IDE cable (CD and HDD)
|
EFI: Since I installed using Zephyroth's 10.5.2, I'm assuming it installs EFI by default?
|
Yes, everything works without patching. No flags needed while booting.
|
| A8N-E
|
nForce 4
|
- Install Method: Leopard 10.5.2 Zephyroth AMD
- BIOS Version: Unknown; Revision: Unknown
- Audio: Install AC97 package on the install menu
- LAN: Install Forcedeth from the install menu
- SATA & IDE: IDE works; SATA not tested
- Install Boot Hang Fix:
- Boot with the DVD
- Press F8, then type "-s"
- Type "cd /usr/standalone/i386"
- Type "dd if=./guid/boot1h of=/dev/rdiskXsY bs=512 count=1" (X is the disk number and Y is the partition number on which you installed Leo)
- Type "dd if=./guid/boot0 of=/dev/diskX bs=400 count=1"
- Type "./startupfiletool -v /dev/diskXsY ./boot_v8"
|
EFI v8 Works
|
Audio & LAN need patching
|
| A8N5X
|
NVIDIA nForce4
|
- Install Method: Kalway 10.5.2
- BIOS Version: 0902
- Nvidia 6600 PCIe working with NVinject
- Chose patches: SSE2_Jas1048_ACPI_APIC, AMD_1052_Patch_test_1, and -legacy flag
- Startup welcome movie played with sound on first boot
|
EFI working
|
Everything but LAN is working
|
| A8N-VM
|
NVIDIA nForce 410
|
- Install Method: Zephyroth Leopard 10.5.2 for AMD
- BIOS Version: 0902; Revision: Unknown
- Audio: ADI AD1986A works with ALC888 patch and no input
- LAN: Works with Zephyroth patch in installation
- SATA & IDE: Works with Zephyroth patch in installation
- partitioned as MBR
|
EFI works
|
Audio & LAN need patching
|
| M2NPV-VM
|
nForce430/GeForce 6150
|
- LEO4ALL V2 KALYWAY & ZEPHYROTH
- Disable usb legacy support in bios to work with ps/2 mouse & keyboard
- Graphics working but no qe/ci (install macvidia or remove nvdaresman.kext)
- Audio Working with 2 channel output but no input
- Lan Working
- SATA Working
- link installation guide for all osx86
|
|
Everything working fine but no qe/ci
|
| P5V-VM Ultra
|
VIA P4M890
|
- Install Method: Kalyway 10.5.1, Combo Updater, & Kernel Patch
- BIOS Version: Unknown; Revision: Unknown
- Audio: Realtek High Definition Audio, ADI AD1986A Soundmax Codec
- LAN: Realtek RTL8201CL
- SATA & IDE: Unknown
|
Unknown
|
Audio needs patching
|
| P5VD2-MX
|
VIA P4M890
|
- Install Method: Kalyway 10.5.1, Combo Updater, & Kernel Patch
- BIOS Version: 1017; Revision: Unknown
- Audio: ADI1986A; works with Azalia
- LAN: Realtek RTL8201CL; works with viarhine.kext
- SATA & IDE: IDE works; SATA needs patching to appleviaata.kext and add 0x53371106 0x2363197B to the device ID
- Shutdown & Restart fully working, Sleep not tested
|
Unknown
|
No, audio & lan need patching
|
| K8V-X
|
VIA K8T800 (VT8383)
|
- Install Method: Kalyway 10.5.2 AMD > SSE2
- BIOS Version: 1001.006
- Audio: ADI AD1980 SoundMAX (integrated) - seems to work but problem with stereo output
- LAN: Marvell Yukon 88E8001 (integrated) - works fine with skge.kext (on Kalyway DVD at installation)
|
Untested
|
No, Audio not working 100%
|
| K8V-XE
|
VIA K8T890
|
- Install Method: Zephyroth 10.5.2 AMD > SSE3 9.2.0 kernel after Uphuck 10.4.9 1.4a drivers install (USB, Azalia, VIA Rhine)
- BIOS Version: 0703
- Audio: Realtek ALC660 (integrated) - works with Uphuck Azalia patch (not Zephyroth patch)
- LAN: Realtek RTL8201CL-LF 10/100M (integrated) - works with Uphuck VIA Rhine driver
- IDE: VIA IDE controller (integrated) - works with Zephyroth VIA drivers
- SATA: JMicron JMB 363 SATA controller (integrated) - used as storage drive
- Video: NV 7300GT works with NVInstaller V41
- Install Boot Hang Fix:
- Boot with the DVD
- Press F8, then type "-s"
- Type "cd /usr/standalone/i386"
- Type "dd if=./guid/boot1h of=/dev/rdiskXsY bs=512 count=1" (X is the disk number and Y is the partition number on which you installed Leo)
- Type "dd if=./guid/boot0 of=/dev/diskX bs=400 count=1"
- Type "./startupfiletool -v /dev/diskXsY ./boot_v8"
|
EFI MBR works
|
Audio & LAN need patching
|
| M2A-VM
|
VIA SB600 / ATi 690g
|
- LEO4ALL V3, default kernel in DVD installer - - On AMD 4600+ x2 CPU
- Motherboard BIOS version 1501
- Audio, LAN, SATA 100% out of box
- SATA DVD install works out of box
- IDE DVD-RW (ATA) working with dcat's kext (search Insanelymac.com)
- nVidia Geforce 8600 GT 256mb (works fully with NVInject 0.2.0, using this method
- Had to switch SATA controller to AHCI in BIOS. Warning: Switch this back to IDE if you installed Windows XP on another drive.
- If you use PS/2 Keyboard and Mouse (instead of USB) disable USB legacy support in BIOS Setup.
|
N/A
|
Everything works 100%, the onboard ATi x1250 card works with Kalyway, probably with LEO4ALL as well.
|
| M2S-X
|
SiS 756 Northbridge + SiS 965L Southbridge
|
- Install Method: Kalyway 10.5.2 Intel/AMD
- BIOS Version: 0603
- Audio: Works OOB no patch needed since onboard C-Media CM6501 8 ch audio is a USB PnP Audio Device detected as PnP Audio Device by the OS [4]
- LAN: SiS 190 10/100 Ethernet does not work, installed a cheap Realtek 8139 PCI LAN Card works OOB.
- IDE: OOB Full UDMA Speed
- SATA: Not yet tested
- USB: Has Issues need to connect USB Devices before turning on the system and can't eject a USB Flash Storage Device. Need to Disabled Legacy USB Devices in BIOS.
- Installed using IDE Drive
|
EFI Works no Vanilla Kernel
|
No
|
| P5SD2-FM
|
SiS 649DX/SiS 966 chipset
|
- Install Method: Flat Image, ToH Kernel, Kalyway 10.5.2 Combo Update
- BIOS Version:; Revision:
- Audio: Works
- LAN: Works
- SATA & IDE: SATA unknown, IDE works
- Optical Drive: NEC DVD_RW ND-4551A works
- Shutdown & Reboot works, Sleep not tested
|
Unknown
|
Yes
|
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. .
. . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . .
. . . . . . . . .
| Hardware Name (alphabetical)
|
Chipset
|
Notes
|
EFI/Vanilla kernel working
|
Fully Working w/o Patch
|
| GA-EP45-DQ6
|
Intel P45 ICH10
|
- Install Method: You can use the same LS8_install_pack as for the P35-DS4
- Audio: ALC889A works (In/Out/Mic/SPDIF) with patch AppleHDA.kext
- LAN: all 4 LAN work w/ vanilla kext, need RTL1000.kext for AFP/Bonjour
- Purple SATA port (gigabyte SATA) Works w/ vanilla AppleAHCI.kext
- Orange SATA port (ICH10) will need a patch IOATAFamily.kext
- Raid on ICH10 working with ChameleonEFI
- IDE Works
- WORKS: Shutdown, Sleep and Reboot
|
ChameleonEFI + Vanilla kernel
|
No
|
| GA-X38-DS5
|
Intel X38
|
- Install Method: Retail DVD + Apple 10.5.2 Combo update (dsmos.kext only needed to boot it)
- BIOS Version: F6
- Audio: ALC889A works (In/Out/Mic/SPDIF) with patch AppleHDA.kext (will break shutdown), using AppleHDA.kext w/ fix shutdown breaks Mic input
- LAN: Works w/ vanilla kext
- Purple SATA port (gigabyte SATA) Works w/ vanilla AppleAHCI.kext
- Orange SATA port (ICH9) will need a patch IOATAFamily.kext
- IDE Works
- WORKS: Shutdown, Sleep and Reboot (Not working on Vanilla kernel)
|
EFI V8 GUID/MBR + Vanilla kernel
|
No
|
| X38-DQ6
|
Intel X38
|
- Install Method: Kalyway 10.5.1 & Kalyway Combo Update
- BIOS Version: 3.70; Revision: Unknown
- Audio: ALC889A works with patch
- LAN: Works OOB
- SATA & IDE: SATA & IDE work OOB
- Optical Drive: Samsung on SATA works
|
Unknown
|
No, audio needs patching
|
| EX38-DS4 (rev 1.1)
|
Intel x38
|
- Install "leoallv2 version" 10.5.2
- all ok (ethernet realtek works fine, audio works fine with alc 889)
|
|
|
| EX38-DS4
|
Intel x38 with ICH9R
|
- Install Method: Kalyway 10.5.1 & Kalyway Combo 10.5.2 Update using PCWIZ's Tutorial and Additional Installers
- Audio: ALC889A Works 100% with PCWIZ's patch (applied twice, first time didn't take.)
- Ethernet: Works 100%
- SATA: All 6 ports work @ 3.0 Gigabit
- USB: 2 ports reported as High-Speed 2.0; 6 ports reported as USB 1.0 (Have not pursued a fix at this time)
- Optical Drive: SATA LITE-ON DVDRW LH-20A1L Works 100%
- IDE: Not tested.
- Shutdown, Sleep and Reboot: Works
- Video Card: EVGA 8800GT 512 MB patched with Scott Dangel's NVinstaller v.41 Installed AFTER Kalyway Combo 10.5.2 Update. Works 100% (Core Image, Quartz Extreme and Rotation All supported)
- Ram: 8 Gigs of 4 x 2GB G.Skill DDR-1000 PC2-8000 F2-8000CL5D-4GBPQ All Recognized and Works 100% Yeah Baby!!!
- Processor: Intel Quad Core Q6700 @ 2.67GHz
|
Yes. Fully supported EFI v8 + Vanilla kernel
|
No. PCWIZ's Addtional installer needed and Scott Dangel's NVinstaller v.41 needed.
|
| GA-EP35-DS3R v2.1
|
Intel P35
|
- Install Method: Kalyway + Apple Update 10.5.2 + Adobe Graphic Update
- BIOS Version: F2
- Audio: Works with AppleHD patch (2.1 and digital)
- LAN: Works out of the box
- SATA works in AHCI mode (NCQ working)
|
Yes. Fully supported EFI v8 + Vanilla kernel
|
No. Audio need patch.
|
| GA-EP35-DS3 v2.1
|
Intel P35 (ICH9)
|
- Install Method: IATKOS 1.0r2 + Apple Update 10.5.2 but direct update from 10.5.1->10.5.3
- BIOS Version: F2
- Audio: Works with AppleHD patch
- LAN: Works out of the box
- SATA works, but detect only 2 drives, need patches to see all SATA drives.
|
Yes. Fully supported EFI v8 + Vanilla kernel
|
No. Audio need patch.
|
| GA-EP35-DS3R
|
Intel P35 & ICH8
|
- Install Method: iATKOS v1.0i, Brazilmac had problems with Rosetta apps
- BIOS Version: F12; Revision: 3.3
- Audio: Audio888 installer package from Skippyretard and AppleHDA patcher v1.20
- LAN: No, edit 8053 to 8056 and 62 to 64 in the Apple Yukon2 kext
- SATA & IDE: Only 2 SATA ports work
|
Unknown
|
No, Audio & LAN need patches
|
| GA-EP35-DS4 Rev. 2.1
|
Intel P35
|
- Install Method: Leo4All v2
- BIOS Version: F12<? conformation please
- Audio: OOB - Used 889 (says DS3R)
- LAN: OOB - Realtek
- SATA & IDE: OOB, ICH9 - AHCI, J - IDE (else no DVD boot)
- Firewire: OOB
- Bluetooth: USB dongle working
- Sleep: OOB
|
Yes (Vanilla 9.2.2)
|
Yes. I used MBR, and does dual-boot XP.
|
| GA-EP35-DS4 Rev. 2.1
|
Intel P35
|
|
Yes (9.2.2)
|
No. Audio patch needed.
|
| GA-EP35-DS4
|
Intel P35
|
- Install Method: Kalyway 10.5.2
- BIOS Version: F2
- Audio: OOB
- LAN: OOB
- SATA & IDE: normal SATA works OOB, but not with software RAID0/1 (may have been my disks however). IDE untested.
- Note: Thanks to all those with GA-P35 and EP35 boards who posted here! Bought board for compatibility - was not disappointed.
|
Yes (9.2.2)
|
Yes.
|
| EP35-DS4
|
Intel P35
|
- Install Method: Retail DVD (See Below) & Netkas to 10.5.2
- BIOS Version: F1; Revision: 1.0
- Audio: ALC885 works with AppleHDA Patcher
- LAN: Works OOB
- SATA & IDE: Both work OOB
- Install Guide by ls8
|
EFI v8 Works
|
No. Audio patch needed.
|
| GA-M57SLI-S4
|
nVIDIA® nForce 570-SLI
|
Metodo de instalaci�n LEO4ALLv3 opciones seleccionadas:
- Netkas 9.2.0 Sleep
- ACPIPlataform sin seleccionar ninguna
- SMBIOS - DDR800
- Audio - ALC 888
- NVInject - 256 MB v 0.2.1 (Trabaja lo basico con el NVidia Universal Installer.mpkg.zip funciona perfecto la tarjeta de video)
- ForceDeth no funciona la tarjeta de red solo la detecta y detecta un modem (no se de donde jj)
- Nforce Test.
Tiene 4 GB de RAM pero al instalar se congela a 3 minutos de acabar hay que remover 2 Gb e intalar si se agrega despues no causa problemas (hasta ahorita).
- DVD SATA
- Disco IDE 500Gb
- LAN Marvell 88E1116 phy (10/100/1000 Mbit)
- CPU AthlonTM 64 X2 4800 Dual-Core
- Audio: Onboard Realtek ALC888 CODEC chip
- Onboard T.I. TSB43AB23 chip
- Video Nvidia Geforce 8600GT
|
unknow
|
No, Video y LAN necesita parche
|
| GA-M61PM-S2 Rev. 2.0
|
NVidia nForce430
|
- Install Method: Zephyroth AMD Rev.1.4033109
- BIOS Version: F3 or F9c
- Audio: Works with patched AppleHDA.kext
- LAN: Not working
- Video: Not tested. Using GeForce 8600GT (PCI-e)
- SATA & IDE: SATA works OOB.
|
Unkown
|
Needs DVD to boot.
|
| GA-M61SME-S2
|
NVidia nForce 6100/415
|
- Install Method: kaly AMD
- BIOS Version: F9
- Audio: Works with patched AppleHDA.kext
- LAN: Not working
- Video: No QE/CI Using GeForce 8600GT (PCI-e)
- SATA & IDE: SATA works OOB.
|
|
|
| GA-M61P-S3 Rev. 1.0
|
NVidia nForce430
|
- Install Method: Leo4Allv3
- Audio: Works using ALC883.kext
- LAN: Not working
- Video: Integrated GeForce 6100 (No QE/CI)
- SATA & IDE: SATA works OOB.
|
Vanilla 9.2.0 kernel works great
|
Still working on LAN Drivers. nForce drivers don't work
|
| GA-P35-DS3
|
Intel P35
|
- Install Method: Kalyway 10.5.1 + Patched Kalyway Update 10.5.2 + Patched Kalyway Kernel 10.5.2 + Graphic Update
- BIOS Version: F12
- Audio: Works with AppleHD patch (2.1 and digital and input)
- LAN: Works out of the box
- SATA Support works without AHCI
- IDE Suppport works
|
Yes. Fully supported EFI v8 + without Vanilla kernel
|
No. Audio needs patch. Bonjour and UPNP services like Connect 360 do not work OOB. Shutdown does not work with vanilla kernel.
|
| GA-P35-DS3
|
Intel P35
|
- Install Method: Kalyway 10.5.1 & Kalyway Combo Updater
- BIOS Version: F12; Revision: 2.1
- Audio: Works with HDA ICH9 ALHC888 works & Apple HDA Patcher v1.20 (EDIT: actually is a ALC889a that patch works great)
- LAN: Works OOB
- SATA & IDE: SATA works with IOATAFamily.kext V1.1
- Optical Drive: LG GSA-H55L IDE (Fully Working with IDE to SATA Cable )
- Shutdown & Sleep don't work, restart unknown
|
EFI v8 & Vanilla Kernel
|
No, Audio needs patching
|
| GA-P35-DS3L
|
Intel P35
|
- Install Method: Kalyway + Apple Update 10.5.2 + Graphic Update
- BIOS Version: F8f
- Audio: Works with patched AppleHDA
- LAN: Works out of the box, Bonjour might need R1000 kext.
- SATA & IDE: SATA woks OOB, AHCI works with all ports with This
- Shutdown and Restart work, Sleep doesn't work
|
Yes. Fully supported EFI + Vanilla kernel
|
No. Audio doesn't work
|
| GA-P35-DS3P
|
Intel P35 + ICH9R
|
- Install Method: Kalyway 10.5.1, Kalyway 10.5.2 Combo Updater & Kalyway Kernel update
- BIOS Version: F8; Revision: 2.0
- Audio: works with ALCinject.kext and AppleHDA.kext
- LAN: LAN working out of the box
- SATA & IDE: SATA works out of the box, using AHCI
|
Yes. Fully supported EFI + Vanilla kernel
|
No; Audio need patching
|
| GA-P35-DS3P (REV 2.1)
|
Intel P35 + ICH9R
|
- Install Method: Leo4All V2
- BIOS Version:; Revision: 2
- Audio: Model, ALC889A - Used Taruga AppleHDA patcher; removed ALCInject.kext its not needed with EFI string
- LAN: Model, Realtek 8111B
- SATA works, in BIOS set all disk modes to ACHI (see patching note) IDE: not tested (yet)
- Samsung SH-203B - Sata interface
- Yes, all.
- Firewire, and USB ports all working
|
Yes; EFI & 9.2.2 vanilla
|
No, Audio needs patching (see above)
|
| GA-P35C-DS3R
|
Intel P35 + ICH9
|
- Install Method: Kalyway + Apple Update 10.5.2 + Graphics Update
- BIOS Version: F4
- Audio: Works with patched AppleHDA + ALCinject (mic works)
- LAN: Works out of the box, but sourceforge Realtek R1000 driver is better (fixes Bonjour)
- SATA: SATA works out of the box, using AHCI on ICH9 controller (JMicron disabled)
|
Yes. Fully supported EFI + Vanilla kernel
|
No. Audio needs patch
|
| GA-P35-DS3R
|
Intel P35 + ICH9R
|
- Install Method: Kalyway 10.5.1 + Kalyway Upd. 10.5.2 + Vanilla kernel 9.2.0 + Graphics Upd.
- BIOS: Sata native mode, 64 bits enabled, Vanderpool enabled, Sleep S0 (S3 doesn't work)
- Audio: works with patched AppleHDA + ALCinject
- LAN: works out of the box
- SATA: works out of the box, using ICH9R without AHCI (JMicron disabled)
|
Yes. Fully supported EFi + Vanilla kernel (kernel 9.2.2 ok)
|
No. Audio needs patch
|
| GA-P35-DS4 (rev.2)
|
Intel P35
|
- Install Method: Kalyway 10.5.1 & Kalyway Combo Updater & Leopard GA-P35-DS4 install pack (http://forum.insanelymac.com/index.php?showtopic=77165)
- BIOS Version: F11; Revision: 2
- Audio: Works with HDA ICH9 ALHC889A
- LAN: Works OOB
- SATA & IDE: SATA(ahci) works and IDE to
- Optical Drive: SAMSUNG SH-S182M IDE
- FW and USB working OOB
- Shutdown & Sleep work, restart unknown
|
EFI v8 & Vanilla Kernel
|
No, Audio needs patching
|
| GA-P35C-DSL
|
Intel P35
|
- Install Method: Kalyway 10.5.1 & Kalyway Combo Update
- BIOS Version: F6; Revision: 2.0
- Audio: ALHC888 and Apple HDA Patcher v1.20
- LAN: Doesn't always work
- SATA & IDE: Both fully working
- Optical Drive: LG GSA-H22N BK (Fully Working)
- Shutdown & Reboot fully working, Sleep not tested
|
EFI v8 + Vanilla Kernel
|
No. Audio needs patch
|
| GA-P31-DSL
|
Intel P31 + ICH7
|
- Install Method: BrazilMac Patched DVD & MBR Partition
- BIOS Version: F8; Revision: Unknown
- Audio: Realtek ALC888 works with AppleHDA Patcher
- LAN: RTL 8111B works OOB
- SATA & IDE: Works OOB
|
EFI v8 Works
|
Audio needs patching
|
| GA-G33M-DS2R
|
Intel G33
|
- Install Method: Kalyway 10.5.1 + manual Update to 10.5.2 + Graphic Update
- BIOS Version: F6
- Audio: Works with AppleHDA patch (stereo out, front panel, digital, mic, line in)
- LAN: Works out of the box
- SATA 6 ports works AHCI
- IDE works
- Thysm00 Guide
|
Yes. Fully supported EFI v8 + Vanilla kernel
|
No. Audio needs patch.
|
| GA-G31M-S2L
|
Intel G31
|
- Install Method: LEO4ALLv3 -selected:Vanilla Kernel 9.2.2, EFI, & ICHx Chipset drivers
- SM Bios 2.3, ACPI 1.0b, PnP 1.0a, DMI 2.0
- Audio: Realtek ALC662 works with AppleHDA patcher & alc662.txt or Use Azallia Audio on installer DVD
- LAN: Works out of the box, reccomended to set ip address manualy. *Bonjour doesn't work properly! Switched to Netgear GA311 for full compatibility.
- SATA & IDE: Work OOB using ICHx chipset patch on installer DVD
- Thysm00 Guide
|
Yes. Fully supported EFI v8 + Vanilla kernel
|
No. Audio needs patch.
|
| GA-K8NF-9
|
NVIDIA nForce4 (4X) MCPs
|
- Install Method: Zephyroth Leopard 10.5.2 AMD
- BIOS version: Unknown
- Audio: Realtek ALC850 Audio AC'97 Codec : Works with Kext but, may works out of the box.
- LAN: Works out of the box
- SATA: Works out of the box
- IDE: Not tested
|
Yes
|
Yes
|
| GA-K8N-SLI
|
NVIDIA nForce4
|
- Install Method: Leo4All v2
- BIOS version: F9
- Audio: Realtek ALC850 -marked 850 driver in Leo install.
- LAN: Works OOB
- SATA: Works OOB
- IDE: Works OOB
- Restart & Shutdown work, no Sleep
|
Yes
|
Yes
|
| GA-K8N51GMF-9
|
NVIDIA nForce 430
|
- Install Method: Zephyroth Leopard 10.5.2 for AMD
- BIOS Version: F7; Revision: Unknown
- Audio: Yes (Stereo) works with "beta4some860_880"
- LAN: Works with forcedeth-nockd.kext
- SATA & IDE: Does SATA work? Any options in BIOS or Patches? Same thing with IDE
- Restart & Shutdown,Sleep fully working
|
Unknown
|
LAN and Audio needs patch
|
| GA-P965-DQ6
|
Intel P965 + ICH8R
|
- Install Method: Kalway 10.5.1, Kalyway 10.5.2 Combo Updater & Kalyway Kernel update
- BIOS Version: F11; Revision: 1.0
- Audio: Realtek ALC888DD; Not Tested
- LAN: Marvell 8053, works OOB
- SATA & IDE: Both work OOB
- Computer wakes from sleep, keyboard doesn't work after that
|
Unknown
|
Yes, audio not tested
|
| GA-P965-DS3
|
Intel P965
|
- Install Method: Kalway 10.5.1 & 10.5.2 Combo Updater
- BIOS Version: F10; Revision: Unknown
- Audio: Works
- LAN: Works
- SATA & IDE: Works
|
Unknown
|
Yes
|
| GA-965P-S3
|
Intel P965 + ICH8
|
- Install Method: Kalway 10.5.1, Kalyway 10.5.2 Combo Updater & Kalyway Kernel update (vanilla) or iATKOS and patch (see below)
- Kalyway: (kernel panics with memory > 3GB)
- Options: EFI_guid, Natit, ALC883, Vanilla kernel +fix
- BIOS Version: F12; Revision: 1.0
- Audio: ALC883; Headphones work (only front panel jack), Line out not working, Digital out not tested
- LAN: Marvell 8056 Gigabit; Works OOB
- SATA & IDE: (both set to AHCI) Only Orange connectors (not purple); Works OOB
- iATKOS: (kernel panics with memory > 3GB)
- Audio: Works OOB
- LAN: Need to repatch after update, save AppleYukon2.kext before upgrade and replace this file after upgrade, reboot twice
- Install iATKOS 1.0i and then upgrade to 10.5.2 with guide here
|
Yes
|
Yes, Audio: only headphone, lineout and digital showing in preferences: not fully tested
|
| GA-965P-S3 rev1.1
|
Intel P965 + ICH8
|
- Installed with PC_EFIv8 using Retail 10.5 Install DVD + 10.5.2 Combo Update (installed from separate Kalyway partition used for system maintenance)
- BIOS Version: F13e; Revision: 1.1
- Audio: ALC883 using SkippyRetard ALC8xx installer enables the use of all Analog Ports (5.1/7.1) as well as Line-In and Mic Jack.
- LAN: Marvell 8056 Gigabit - Needs plist configuration (change 8053 to 8056 IDs) of IONetworkingFamily.kext (vanilla)
- SATA & IDE: JMicron IDE not useable under AHCI, JMicron SATA AHCI useable with plist configuration of AppleAHCIPort.kext (generic), ICH8 last 2 ports (of 4 total) not working with 10.5.2 IOAHCIFamily.kext - 10.5.3 kexts fixes this.
- No 3072MB/4096MB (3GB/4GB) memory limit as compared to other Custom Installations (Kalyway/iATKOS/Loe4ALL) due to the absence of JMicronATA.kext and AppleVIAATA.kext - Tested on 6144MB (6GB) and 8192MB (8GB) equipped systems.
|
Yes
|
Yes; Audio needs patching for 5.1/7.1 output, LAN needs plist configuration, AHCI needs plist configuration, EFI Strings for GFX and Audio (if not using NVInject/NVKush/NATIT and ALCInject)
|
| GA-945GCM-S2C
|
Intel 945G + ICH7 Chipset
|
- Install method: Kalyway 10.5.1 Install DVD
- Update to v10.5.2: Netkas method
- kernel 9.2.2 ok
- BIOS version F4, Rev. 1.0
- Audio requires AppleAzaliaAudio.kext
- LAN working out of the box
- SATA and IDE working out of the box
- Certain applications (i.e. FireFox) cause Intel GMA950 glitches
|
EFI + Vanilla kernel 9.2.2 working
|
No; Audio needs patching
|
| GA-945GCM-S2L
|
Intel 945G + ICH7 Chipset
|
- Install method: Kalyway 10.5.1 Install DVD
- Update to v10.5.2: Kalyway 10.5.2 Combo update + Apple update + Kalyway 10.5.2 Kernel update
- Audio requires Azalia_Out.kext on Kalyway
- LAN not working out of the box need to use RTGMac_v1.1.6.zip
- SATA and IDE working out of the box
|
EFI + Vanilla kernel working
|
No; Audio/LAN needs patching
|
| GA-945GCM-S2L
|
Intel 945G + ICH7 Chipset
|
- Install Method: Kalyway 10.5.2 Install DVD then Kalyway 10.5.3 Upgrade then Apple update to 10.5.4
- Audio: Working with Azalia_Out.kext or this driver [[6]]
- LAN: Works OOB with default settings on Kalyway 10.5.2 Disk, however after computer wakes from sleep it has no LAN connectivity
- SATA & IDE: Both Working (on all 10.5.2 , 5.3 and 5.4)
- Optical Drive: LG super-multi - works fine
- Shutdown and sleep work but LAN connectivity is lost after waking from sleep
|
EFI + Vanilla kernel working
|
Everything seems to work OOB. Audio can be improved by using this guys driver[[7]]
|
| GA-945GCMX-S2
|
Intel 945GC + ICH7
|
- BIOS version: F4, Rev. 6.6
- (1) Installation (v10.5.0) method: Onetrack method with EFI v8.0 on GPT using iGuru guide
- Update to v10.5.2: Netkas method
- Audio (ALC 888): Works with skippyretard patch
- Video (GMA 950): Works with modified AppleIntelIntegratedFramebuffer.kext from BrazilMAC guide
- LAN: Works out of the box
- IDE and SATA: Works out of the box
- Sleep/Wake, Restart, Shutdown work
- ----
- (2) Installation method: iATKOS
- Audio: Works OOB
- LAN: Works OOB
- SATA & IDE: Works OOB
|
Yes
|
No. Audio and video need patches
|
| GA-945GCMX-S2
|
Intel 945GC + ICH7
|
Am using onboard GMA950 video and Celeron D 630.
With Leo4all v3, everything works fine - Patched 9.2.2 Kernel, ALC888, Realtek LAN, GMA950 older version (Resolution Change version), ICHx support
|
EFI bootloader untested, due to usage of Celeron D CPU. Minor graphics glitches, mainly related to mouse cursor.
|
Yes
|
| GA-945GZM-S2
|
Intel 945 Chipset
|
- Install method: Kalyway 10.5.1 + Kalyway 10.5.2 ComboUpdate
- BIOS version unknown, Rev. unknown (1/29/07)
- Audio needs skippyretard's driver
- LAN works out of the box
- SATA and IDE working
|
Unknown
|
No; Audio needs patching
|
| GA-945P-S3
|
Intel 945P + ICH7
|
- Install Method: iATKOS V1.0i & Kalyway 10.5.2 Updater
- BIOS Version: Unknown; Revision: 3.3
- Audio: Realtek ALC888 8 Channel Audio works
- LAN: Realtek 8111B Gigabit Ethernet works
- SATA & IDE: Both work
|
Unknown
|
Yes
|
| GA-8I865GVMK F9 (Socket 478)
|
Intel® 865G GMCH & ICH5
|
- Install Method: Kalyway
- Audio: Realtek ALC655 works
- LAN: Intel PRO/100 VE Ethernet Controller works
- SATA & IDE: Unknown
- Optical Drive: Unknown
|
Unknown
|
Unknown
|
| GA-G31M-S2L
|
IntelG31 + ICH7
|
- Install Method: Kalyway 10.5.2 + Kalyway ComboUpdate10.5.3 + OnlineUpdate10.5.4 (all Vanilla)
- BIOS Version: unknown
- Audio: ALC662, works with Taruga's HDA-patcher 1.20 & ALC662.txt from his page
- LAN: not tested (seems to be working OOTB though)
- SATA & IDE: no issues
- Optical Drive: SATA & PATA work
- Shutdown, reboot, sleep work fine
- Onboard-GFX: not tested
- HIGHLY RECOMMENDED!
|
YES (EFI_v8 & Vanilla, MBR)
|
Sound needs patching
|
| GA-MA69G-S3H (Socket AM2)
|
AMD 69G & SB600
|
- Install Method: Kalyway 10.5.2, AMD patch
- Bios F6
- Audio: Realtek ALC889A (not tested)
- LAN: Realtek RTL8110 GE Ethernet Controller works
- SATA: works
- IDE: Unknown
- Optical Drive: works with SATA
- Onboard video does not work
|
No
|
Unknown
|
| GA-M61SME-S2 (Socket AM2)
|
nForce 405 / nVidia Geforce 6100
|
- Install Method: Kalyway 10.5.2, AMD patch
- BIOS Version:; Revision:
- Audio: nForce AC97, worked out of box
- LAN: nForce onboard 10/100, Failed
- VIDEO: not tested, Geforce 8500GT used instead.
- SATA: Installer fails to load, but once OSX is installed runs fine.
- Optical Drive: works with SATA
- Yes
- No
|
Yes
|
No, Lan needs patching.
|
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
| Hardware Name
|
Chipset
|
Notes
|
EFI/Vanilla kernel working
|
Fully Working w/o Patch
|
| Intel D201GLY2(A)
|
Silicon Integrated Systems® SiS964 Chipset
|
- Install Method: Leo4All
- Audio (ADI, AD1881), not working
- Video (SIS Mirage 1), working in VESA mode (no acceleration)
- LAN (SIS900) not working
- USB working
- IDE working, SATA controller not working
Notes: Soldered CPU, 1x PCI slot, 1x DDR2 RAM slot.
So it's impossible to have LAN and Audio working.
Unfortunately, no cheap Hackintosh with this one.
|
EFI is working Vanilla not tested
|
|
| Intel D5400XS(Skulltrail)
|
Intel® 5400 Express Chipset
|
- Install Method: Kalyway 10.5.2 DVD
- Audio Sigmatel STAC9274D Working with Apple HDA Patcher 1.16 and STAC9274D codec dump available at HERE
- LAN Intel Gigabit Ethernet working out of box
- USB working with Printers, and Microsoft WIreless Desktop 7000 Transceiver. External USB storage either not recognized or EXTREMELY slow transfer speeds
- IDE working, SATA controller working in AHCI mode with kexts from HERE No RAID support yet
- Optical Drive LG GSA-H55LI IDE drive works out of the box
|
EFI is working Vanilla not tested
|
Audio and SATA controller require patching
|
| DP35DP
|
Intel P35 + ICH9
|
- Install method: Kaliway's 10.5.1 DVD + 10.5.2 Combo Update following this tutorial
- BIOS Version: DPP3510J.86A.0413
- Audio: Works with Kext Helper & STAC9271D_0x83847627_testing codec downloadable here
- Onboard LAN does not work (buy a cheap realtek)
- USB, Firewire work out of the box
- IDE/ATA does not work
- SATA works in IDE Mode
- Optical Drive must be SATA or ATA to perform install
- To make restart fully work, install 10.5.3 combo update from Kalyway
|
EFI v8 + Vanilla Kernel Working, Restart and Sleep work
|
Audio requires patching
|
| DG33FB
|
Intel G33
|
- Install method: Kaliway's 10.5.1 DVD + Kalyway's hacked Combo update 10.5.2 and Vanilla Kernel 9.2
- BIOS Version: DPP3510J.86A.0326
- Audio: Works with AppleHDA & ALC888 codec dump (Including BIOS Update herefrom Intel)
- Onboard LAN does not work
- USB, Firewire work out of the box
- IDE works with Patching
- SATA works in AHCI Mode
|
EFI v8 + Vanilla Kernel Working
|
Audio and IDE require patching
|
| DG33FB
|
Intel G33
|
- Install method: Kalyway 10.5.2 DVD_Intel_AMD and Vanilla Kernel 9.2
- BIOS Version: DPP3510J.86A.0413
- Audio: Works with ALC888
- Onboard LAN does not work (Realtek 8139 PCI card native OOB)
- USB (6+2) & Firewire work out of the box
- Onboard USB & Firewire work for front panel
- IDE works, no Patching
- SATA works in AHCI & IDE Mode
- IDE & SATA Optical works, fully iTunes & DVD Player functional
- Onboard Intel GMA3100 graphics works, 1024x768 fixed resolution, not further tested
- EVGA Nvidia 7600GT KO - all resolutions, NVinject-256 via Kalyway disc
|
EFI v8 + Vanilla Kernel Working
|
Audio requires patching. Full sleep/shutdown/restart.
|
| DG33TL
|
Intel G33
|
- Install method: Kaliway's 10.5.2 DVD
- BIOS Version:
- Audio: Works with Patching
- Onboard LAN does not work
- Onboard Video does not work
- USB, Firewire work out of the box
- IDE (not tested)
- SATA works in AHCI Mode
|
EFI v8 + Vanilla Kernel Working
|
Audio requires patching; For more information, see Intel DG33TL Motherboard on the wiki, or this forum post on insanelymac.org.
|
| D975XBX2 (BADAXE2)
|
Intel 975X Express ( ICH7 Southbridge)
|
- Install Method: Leo4allv3 vanilla 9.2.2
- BIOS Version: 2813
- Audio: Onboard Unknown,I'm using external Rme Fireface 400 (Firewire)
- LAN: Intel® 82573E/82573L Gigabit Ethernet Controller, no patch, works!
- SATA & IDE: Both work! no patch
- Optical Drive: Samsung RW. Works fine
- Do shutdown,Yes with ACPIPI old 1.1.0
|
Yes both working
|
Need only contained dvd patch and driver. Install ichx, acpipi 1.1.0 otherwise no shutdown
|
| D975XBX2KR (BadAxe2)
|
Intel 975X Express
|
- Install Method: BrazilMac 10.5 + EFI v8 MBR, Vanilla kernel
- BIOS Version: 2813 [BX97520J.86A]; Revision: Unknown
- Audio: Need to patch with AppleHDAPatcher_v1.16 (STAC9274D)
- LAN: Need to replace IONetworkingFamily.kext from 10.4.9 + EFI strings to fix various UUID errors and TimeMachine
- SATA & IDE: Work OOB
|
Yes, both work
|
|
| D975XBX2
|
Intel 975X & ICH7DH
|
- Install Method: iATKOS_v1.0i vanila + 10.5.2 direct update (Netkas)
- SATA AHCI (GUID Partitions), IDE, USB, FireWire and Lan fully working.
- GF7600GT as EFI (string added): no injectors
- Sigmatel STAC9274D audio working with Taruga's AppleHDAPatcher 1.16
- Onboard Marvel88SE61XX not working
|
Yes (pc_efi_v8 + pc_efi_v7.4)
|
Sigmatel Audio requires patch
|
| Intel D945GCLF
|
Intel® 945GC and ICH7
|
- Install Method: Kalyway 10.5.2 (kernel 9.2.0 + usb patch because System.kext is by default 9.2.2 and should be 9.2.0)
- Integrated Intel® Atom 1.6ghz (HT) processor working (system think it's a Core Solo 1.6ghz)
- Realtek ALC662 audio working (Mic Not working yet)
- Intel Graphics Media Accelerator 950 (QE/CI fully supported. It works like a charm!)
- LAN (i don't know... disabled in bios because in my dual boot, Linux gave kernel panic with this netcard) - LAN do work but after sleep lost IP connection, so suggest to fix with Fix IP.
- Six USB 2.0 ports working
- Two SATA ports and One PATA IDE working
- Sleep works
This is a perfect system! And really cheaper (54€)
Note: On-board LAN chipset does not work, most linux distributions also suffer from the same problem. Some distributions might not support video resolution over 1280x1024 out of the box. After patching with a different version of IntegratedFrameBuffer kext, 1680x1050x32 works fine but no 3D support.
|
Efi working, Vanilla working
|
No patch needed! Everything works out of box
|
| Intel D945GNT
|
Intel® 945G Express Chipset
|
- Install Method: All
- Audio (Sigmatel 9220) works with patch 9200.pkg
- LAN works with ASUSP4800vm.pkg {for tiger add product ID to AppleIntel8255x.kext}{for leopard need IONetworking family.kext}
- SATA & IDE works
|
Efi is working Vanilla not tested
|
- Sigmatel Audio require patch
- Intel® Pro/100ve requires driver
|
| 945GNTKLR
|
Intel 945G
|
- Install Method: Kalyway 10.5.1 & Combo Updater
- BIOS Version: Unknown; Revision: Unknown
- Audio: HDA Intel 9221 & Apple HDA Patcher v1.20
- LAN: Works OOB
- SATA & IDE: SATA & IDE work
- Video: GMA950 works by replacing current appleIntelIntegratedFramebuffer.kext with version 1.4.20
- Optical Drive: Pioneer 111D fully working
|
EFI works, Vanilla doesn't
|
Audio needs patching
|
| D945GTP
|
Intel 945G
|
- Install Method: iATKOS or Kalyway 10.5.1 with Kalyway 10.5.2 update
- BIOS Version: Unknown; Revision: Unknown
- Audio: Sigmatel 9220 needs patch
- LAN: Intel PRO 10/100 needs patch
- SATA & IDE: SATA works, IDE not tested
|
Unknown
|
No
|
| D945GCL
|
Intel 945
|
- Install Method: Kalyway 10.5.2 DVD Intel_Amd
- MBR, disk name Leopard
- had to patch network and audio
- SATA and PATA work OOB
- details here
|
EFI v8 and Vanilla 9.2.2 working
|
needs audio and network
|
| D915GAV
|
Intel 915G
|
- Install Method: Kalyway 10.5.1 and modified 10.5.2 Combo Update. See gizmoarena for more info
- BIOS Version: Unknown; Revision: Unknown
- Audio: Realtek ALC882 HD works with Azaila patch
- LAN: SURECOM EP320X-R (Realtek chipset) works OOB
- SATA & IDE: Works OOB
|
PC-EFI
|
Audio Needs Patching
|
| D915GAG
|
Intel 915G
|
- install Method: Kalyway 10.5.2 DVD Intel_Amd
- MBR
- kernel kabyl 9.2.2
- stock options for sound and network OOB
- AppleOnboardPCATA and AppleGenericPCATA
- netkassmbios
- see here for details
|
no, P4 Prescott 630
|
yes
|
| D865GLC
|
Intel 865
|
- Install Method: Brazilamc Patched DVD with Kalyway 10.5.2 Updater & Brazilmac Post-Patch
- BIOS Version: Unknown; Revision: Unknown
- Audio: Works OOB
- LAN: Works OOB
- SATA & IDE: IDE works, SATA not tested
|
No
|
Yes
|
| D915GAV
|
Intel 915G
|
- Install Method: Kalyway 10.5.1 and modified 10.5.2 Combo Update. See gizmoarena for more info
- BIOS Version: Unknown; Revision: Unknown
- Audio: Realtek ALC882 HD works with Azaila patch
- LAN: SURECOM EP320X-R (Realtek chipset) works OOB
- SATA & IDE: Works OOB
|
PC-EFI
|
Audio Needs Patching
|
| Intel DG31PR
|
Intel G31- no qc/qe
|
- Install Method: LEO4ALL V2 picked the options for Vanilla 9.2.2, sound, net
- BIOS Version: 0047; Revision: BIOS Update 0047 PRG3110H.86A
- Audio: Model, RealTek* ALC888, used alc888 patch included on DVD
- LAN: Model, RealTek* RTL 8111, used realtek patch included on DVD
- SATA & IDE: 3 sata drives all working no problems, including a ATA usb backup drive
- Optical Drive: LG IDE lightscribe works perfect with lightscribe software and toast 9
- Do shutdown, reboot and sleep work? perfect
|
Yes, Yes
|
Audio requires patching. Kalaway/iatkos req. the gparted method and wouldn't work with a partitioned disk but leo4all will.
|
| DG31PR
|
Intel® G31
|
- Install Method: Kalyway 10.5.2
- BIOS Version: 0047 [PRG3110H.86A ]
- Audio: Realtec ALC888, use this patch: AppleHDA patcher.
- Lan: Realtek* RTL8111-GR Gigabit Ethernet Controller, working OOB.
- SATA & IDE: Both are working fine OOB.
- Shutdown, sleep and reboot: Working fine.
|
EFI v8 and Vanilla kernell working.
|
Audio needs tweaking, use the AppleHDA patcher v1.20, with this file.
|
| Intel® Desktop Board DQ35JO
|
Intel® Q35 Express Chipset
|
- Install Method: Kalyway 10.5.2 DVD
- BIOS Version: JOQ3510J.86A.0559.2007.0726.0425
- Audio: Realtec ALC268, use/select AppleAzalia audio driver in the installer.
- Lan: Intel® 82566DM Gigabit Ethernet Controller, currently NOT working.
- SATA & IDE: Both are working fine OOB.
- Shutdown, sleep and reboot: Working fine except sleep. But this (sleep) may depend on what you attached to your motherboard.
|
EFI v8 and Vanilla kernell working.
|
Audio needs tweaking, use ALC268 driver from AppleHDA Solution.
|
| D865PERL (no LAN)
|
Chipset (865PE and ICH5)
|
- Install Method: Kalyway 10.5.2
- Audio: SoundMax Integrated Audio (included in DVD)
- LAN: D-Link DFE-530TX+ (works OOB)
- SATA & IDE: SATA and IDE work. IDE recognized as ATA Bus
- Optical Drive: LiteOn DVD Reader: Works OOB...BenQ Dual Layer DVD Burner: Works OOB...burns DL and DVDs
- GeForce 6600 AGP work using NVkush or NVinject 0.2.1
- Shutdown, Restart and Sleep work
- Other Details:
|
PC-EFI work, Vanilla doesnt
|
. . . . . . . . . .
. .
| Mainbord
|
Chipset
|
Notes
|
EFI/Vanilla kernel working
|
Fully Working w/o Patch
|
| P35 Neo-F
|
Intel® P35 Chipset/Intel® ICH9 Chipset
|
- This Board Does not work with Standard BIOS from MSI!!!
- I was lucky to find someone who did the trick and now have it running with a moded BIOS
- You can find the moded BIOS here: [8]
- Install Method: Kalyway 10.5.2 no patches
- Onboard Works(Except Input)
- Ehternet: Works (sometimes doesn't, still trying to figure out the problem)
- USB: Works (sometimes doesn't, still trying to figure out the problem)
- SATA: Works
- IDE: doesn't work
|
EFI+Vanilla Working with E8200
|
No patches needed
|
| MSI 915PL Neo-V
|
Intel 915PL Chipset
|
* Install Method: Kalyway 10.5.2 DVD
- BIOS Version: latest;
- Revision: Unknown
- LAN: works without problem
- Audio: Works with kalyway out-of-box
- USB: works perfectly
- SATA: Works
- IDE: Works
|
| K9N Platinum
|
Nvidia nForce 570 Chipset
|
* Install Method: Kalyway 10.5.2 With AMD Patches, Realtech Audio Drivers, USB-Ehci fix on insanelymac forum.
- Install Method: Kalyway 10.5.1 & Combo Update.
- Installed using Vanilla Kernel, and EFI Complete Install and Reboot Use -x on first boot Setup First boot in safemode.
- BIOS Version: Unknown;
- Revision: Unknown
- LAN: unknown
- Audio: Works with kalyway included drivers
- USB: Works with USB-Ehci kext replacement (you can find it on: insanelymac forum.)
- SATA: Works
- IDE: Works
|
EFI+Vanilla Works
|
Kalyways included AMD Patches, Realtech audio drivers & USB-EHCI Fix on insanelymac forum.
|
|
MSI P35 NEO 3-F
|
Intel P35 / ICH9
|
Install method: Kalyway 10.5.2
* BIOS AMI version 1.12
* works only with SEE2-Patch
* Audio ALC888 does not work
* Ethernet RTL8111 works with RTL1000-Patch
* USB works
* SATA works
* Grafik ATI Radeon HD2600 PCIE works with ATI-Patch
* IDE not tested
|
EFI+Vanilla working with E6750
|
Patches for Audio, SEE2 support, ATI and Ethernet needed
|
| P965 Neo2 -FI
|
Intel® P965 Chipset/Intel® ICH8 Chipset
|
- Install Method: Leo4All 10.5.2 vanilla, EFI MBR
- Onboard audio disabled (b/c of USB external sound here)
- BIOS 3.8 WORK! (Only when DOT is CPU ONLY and set to 1%)
- LAN, SATA work(tested with 1 HDD,1 DVD-RW), IDE not tested
|
EFI+Vanilla working with E8200
|
Onboard audio need patch
|
| P965 Neo2(-FI)
|
Intel 965/ICH8 Chipset
|
- Install Method: Kalyway 10.5.1 EFI Guid (updated to vanilla 10.5.2
- Audio needs ALC888+Azalia Driver from here
- BIOS Ver: 3.7 (3.8 DOES NOT WORK!)
- The rest all works out of the box except IDE and the 5th SATA port because its on the same chip as IDE (Marvell ® 88SE6111)
- link to motherboard overview
|
EFI+vanilla working on my Core 2 Quad Q6600
|
No, Everything works, except IDE and audio needs ALC888+Azalia patch
|
| P965 Neo
|
Intel 965 Chipset with ICH8 Southbridge
|
- Install Method: Kalyway 10.5.1 Efi Guid or MBR
- Audio needs ALC883 Driver from install DVD
- BIOS Ver: Latest
- LAN (Realtek 8110SC) Works out of the box
- No IDE support (Because of JMicron Chip) All drives should be sata, All IDE should be empty. IDE DVD in USB external Box return /com.apple.Boot error.
- Disable Lan Option ROM from BIOS settings
|
EFI working, Vanilla unknown
|
No, Everything works, except audio needs ALC883 driver from Kalyway DVD
|
| 975X Platinum Power Up
|
Intel® i975 Chipset/Intel® ICH8 Chipset
|
- Install Method: iatkos v1.0i + Kallyway 10.5.2 Update - vanilla, EFI MBR
- Onboard audio working
- LAN, SATA, IDE work
|
| 945GM3-F
|
Intel 945 & ICH7
|
- Install Method: Kalyway & vanila_acpi_fix
- BIOS Version:; Revision:
- Audio: Realtek Audio works with Azalia
- LAN: Realtek LAN works OOB
- SATA & IDE: SATA works
|
Unknown
|
Audio needs patching
|
| P965 Platinum(-FI)
|
Intel 965/ICH8 Chipset
|
- Install Method: Kalyway 10.5.1 EFI Guid (updated to vanilla 10.5.2
- Audio needs ALC888+Azalia Driver from here
- BIOS Ver: 1.6 (1.8 DOES NOT WORK!)
|
EFI+netkas 10.5.2 kernel or toh
|
No, Everything works, except IDE and audio needs ALC888+Azalia patch
|
| MSI-7223/915GVM3-V
|
Intel 915GV / ICH6
|
Install method: Kalyway 10.5.2
- Everything except onboard video works. Out/In put's on audio work fine.
- Onboard (GMA900) doesn't work due to being too old for leopard.
|
Unknown
|
Yes, except for onboard video (Not supported).
|
| K9N SLI-2F
|
NVIDIA nForce 570 SLI MCP Chipset
|
- Install Method: Zephyroth 10.5.2 Install DVD
- BIOS Version: 3.70; Revision: Unknown
- Audio: Works after patching using AppleHDA Patcher 1.17 with ALC883 linux codec dump from here
- LAN: Doesn't work
- SATA & IDE: SATA works with nForce Chipset Drivers, IDE works OOB
- Optical Drive: LITE-ON LH-18A1H works
|
Unknown
|
No, LAN doesn't work, Audio needs patch
|
| K9N6SGM-V
|
NVIDIA MCP61 (nForce 4 & 6100 video)
|
- Install Method: Zephyroth 10.5.2 for AMD
- BIOS Version: 052207; Revision: Unknown
- Audio: ALC883, patch on DVD does not work, Taruga ALC883 works for output (input not tested, but recognized)
- LAN: Doesn't work
- SATA & IDE: Both work OOB
- Using 9.2 on Zephyroth enables USB
- Not selecting a kernel during install allows Apple updates, but no USB
|
No
|
Audio needs patch, LAN doesn't work
|
| MSI K8N NEO4 FI
|
NVDIA NFORCE4
|
- Install method Leo4Allv2 Kernel during installation
- BIOS unknown
|
NETKAS
|
Need no Patches everything works
|
| MSI P6N Diamond
|
nVidia 680i
|
- Install Method: Kalyway 10.5.2 Intel DVD (TPB)
- BIOS Version: v1.3; Revision: Unknown
- Audio: On-board Creative X-Fi xtreme audio DOES NOT WORK WHAT-SO-EVER. USB Audio, like a headset, will work though.
- LAN: On-board LAN, works with driver "forcedeth". Has some issues when dual-booting with Windows Vista.
- SATA & IDE: Everything works perfectly. Just make sure if you dual/triple-boot to shutdown your other OS's completely or OSX cannot read. I use Ext2FS for my Linux partition and NTFS-3g for my Vista partition. All work fine.
- Optical Drive: SONY DVD-RW DRU-540A. Works fine.
- Do shutdown, reboot and sleep work? Yes, have not tested sleep.
- Sleep, Speedstep, nForce, and Modbin kernels all work. Vanilla and kabyl kernels do not work.
|
PC-EFI works. Vanilla Kernel does not.
|
No patching required.
|
| MSI P6N SLI
|
nVidia 650i
|
- Install Method: Kalyway 10.5.2 Intel/AMD DVD
- BIOS Version: v2.2; Revision: 06/18/2007
- Audio: On-board nForce Audio ALC888 Codec works like a charm OTB
- LAN: On-board LAN cannot receive data, not working. Tried with up-to-date "forcedeth".
- SATA & IDE: Everything works perfectly. Installed to IDE just to make sure. Couldn't install from SATA DVD drive but maybe that was because I used a DVD+RW
- Optical Drive: SATA works fine
- Do shutdown, reboot and sleep work? Yes, have not tested sleep.
- I use the nforce kernel, haven't tried the others.
|
PC-EFI works. Vanilla Kernel does not.
|
No patching required. You _have_to use BIOS version 2.2 though. 2.1 will force you to use cpus=1, 2.5 (the latest) would hang the kernel at the memory prompt.
|
| Neo2-Digital K9AG
|
AMD RS690G
|
- Install Method: Zephyroth 10.5.2 V1 for AMD & 9.2.0 Kernel during installation
- BIOS Version: 1.14
- Audio: Realtek ALC888 works with ALC888Audio.mpkg
- LAN: Realtek RTL8111B
- SATA & IDE: Work
- Optical Drive: TSSTcorpCD/DVDW SH-S183A works fine
- Shutdown & Reboot work, Sleep not tested
|
Unknown
|
Audio needs patching
|
| G31M2
|
Intel IG31 ICH7
|
- Install Method: Leopard Retail + Updated to 10.5.3
- Bios Version: 7383v52 here
- Audio: Realtek ALC888 Works with AppleAzaliaAudio
- LAN: Realtek RTL8111B Works OOB
- STATA & IDE: Works OOB
- Optical Drive: Pioneer DVR-213NP SATA
- VGA: Used nVidia GeForce 7600GT PCIe (gfxutil efi mode)
- Shutdown & Reboot work, Sleep not working
|
PCEFI & Vanilla Kernel
|
Audio needs AppleAzaliaAudio
|
| MS-7058
|
Intel i915P/i915G
|
- Install Method: Kalyway 10.5.2 Intel DVD
- Bios Version: 1.9B0
- Audio: CMedia 9880
- LAN: Marvell Yukon 88E053 PCI-E Gigabit Ethernet Controler
- STATA & IDE: Works.
- VGA: Used nVidia GeForce 6600 PCIe
|
Sleep Kernel
|
Audio: Works with default drivers (Azalia High Definition)
|
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Please specify if your card is AGP, Integrated, PCI or PCI-E.
Also, place chip and board manufacturer in their respective column.
. . . . . .
. . . . . . .
| Hardware Name
|
Board-Manufacturer
|
Notes
|
QE / CI
|
Resolution
|
Fully Working w/o Patch
|
| Radeon X1300 Pro 256MB
|
ATI
|
Works with the NatitX1300 r1v1 Installer Download
|
Both
|
All Resolutions
|
No, not fully. You can just use DVI - but there's no prob to adapt it.
|
| ASUS EAX1600 Pro 256MB
|
ASUS
|
Works with manual modify the video kext with your id]
|
Both
|
All Resolutions
|
fully working.
|
| Radeon X1600P 256MB
|
ATI
|
Used Maclovin's patch from here and added the deviceID 71C2 in ATIRadeonX1000.kext after intstall
|
Both
|
All Resolutions
|
Yes with patch
|
| Radeon X800GT 256MB
|
Sapphire
|
Works with Zephyroth AMD 10.5.2 Rev.1
|
Unknown
|
1280x1024
|
Yes
|
| Radeon x1650 Pro 256MB PCIE
|
Sapphire
|
No DVI
|
Yes
|
All
|
Working with with Modbin's Driver patch. Install the Apple Graphics Update first (here is the installation file).
Added: In my case, somehow installation of Modbin's package did not does the job. However, I extracted the kexts from the installation package matching with my device ID (using Pacifist) and drag those kexts to /System/Library/Extension, authenticate and replace, then I got QE/CI/Rotation and resolutions (though missing 1680x1050).
|
| Radeon EAX1650 256DDR3 Gamer Edition
|
ASUS
|
Fully working
|
Both
|
All
|
Working with with MacLovin's Driver patch (here is the installation guid).
Recognized as X1600.
|
| Radeon X1800XT 512MB
|
ATI
|
Diabolik's X1800 Natit, enter Dev ID in ATIRadeonX1000.kext
|
QE Works, CI Works
|
All Resolutions
|
Yes with patch
|
| Radeon X1900XT 512MB
|
Connect3D
|
No Patches
|
QE Works, CI unknown
|
All Resolutions
|
Yes
|
| Radeon X1900XT 512MB
|
Saphire
|
Used X1900_XT_EFI_VGA_Installer_0.1.pkg
|
Both work
|
All Resolutions
|
Yes
|
| Radeon X1900XTX 512MB
|
ATI
|
No Patches
|
Yes
|
All Resolutions
|
Yes
|
| Radeon X1950 Pro 256MB
|
Sapphire
|
Bronya's 10.5.2(9c16) patch here (Note: c16 works QE/CI and RC, c32 only RC)
|
Yes
|
Yes
|
Needs Bronya's patch.
|
| Radeon X1950 Pro 512MB
|
Powercolor
|
Bronya's 10.5.2 patch here
|
Yes
|
Yes
|
Needs Bronya's patch as described.
|
| Radeon X1950 XTX 512MB
|
Sapphire
|
Used this kext to enable full support
|
Yes
|
All Resolutions
|
Fully working with patch
|
| Mobility Radeon X2300 128MB
|
ATI
|
Read [9]
|
Yes
|
1280x800x32 (not always work, depends on laptop model)
|
Working with patch (some mouse tearing, some video glitches)
|
| ATI Radeon HD 2400 PRO 256MB
|
ATI
|
Used Netkas Newest Natit -->here from Feb. 26 along with editing ATIRadeonX2000.kext with Dev ID 94c3
|
Yes
|
All Resolutions
|
No... Need Natit Feb 26 plus you MUST use the DVI port w/ a DVI to VGA adapter to get things working with this card!
|
| ATI Radeon HD 2600XT 256MB
|
Sapphire
|
Used Natit; DeviceID: 0x9588
|
Yes
|
All Resolutions
|
Yes with Natit
|
| ATI Radeon HD 2600XT
|
Sapphire
|
New natit.kext from Netkas as of 2/26 here
|
Yes
|
All Resolutions
|
No, need natit.kext from netkas (new 2/26). w00h00, sleep now works.
|
| ATI Radeon HD 2600XT
|
Sapphire
|
New Natit.kext from Netkas required (feb/26/2008) same as Installation-Hints
|
Yes
|
All Resolutions, Dual Head, Pivot
|
No OOTB, needs Netkas' NATIT. Here NO sleep with Asus P5LD2 VM / edit: sleep now works for me aswell, was mobo config issue...
|
| ATI Radeon HD 2600XT 256MB
|
Gigabyte
|
New Natit.kext from Netkas required (feb/26/2008) same as Installation-Hints and Kext Installation-Hints
|
Yes
|
All Resolutions, Dual Head, Pivot
|
No, needs Netkas' NATIT (26.02.2008)
|
| ATI Radeon HD 2600pro
|
ONDA
|
New ATIRadeonX2000_Leopard.pkg from here (only one package with netkas's natit 2/26/08 and white menu fix)
|
Yes
|
All Resolutions
|
Fully working with patch.
|
| ATI Radeon HD 2600pro 512MB
|
Visiontek
|
Yes With ATIRadeonX2000_Leopard.pkg
|
Yes
|
All Resolutions
|
Works with patch.
|
| ATI RADEON HD 2600 PRO 512
|
SAPPHIRE
|
TRIAKIS AND WHITE MENU
|
YES
|
ALL RESOLUTIONS
|
YES
|
| ATI Radeon HD 2600Pro 512Mb
|
ASUS
|
White Menu Fix from and adding device id to ATIRadeonX2000.kext
|
Yes
|
All Resolutions
|
Yes without Natit patch
|
| ATI Radeon HD 2600 Pro 512MB
|
Gigabyte
|
Used ATIRadeonX2000 Leopard.pkg
|
Both
|
All Resolutions
|
No, needs patch
|
| ATI Radeon X2900XT
|
ATI
|
Unknown patches used
|
Yes
|
All Resolutions
|
Yes - Not known if patch used
|
| Radeon HD 3650 512MB DDR2
|
Sapphire
|
Used the installer from this post, on iATKOS 2.0i. No need for aditional patching, kexts editing etc. Connected to a VGA monitor, using a dvi2vga adapter.
|
Both
|
All Resolutions
|
Works, with the mentioned installer.
|
| Radeon HD 3650pro 256MB DDR2
|
HIS
|
Used the installer from this post, Dont use Kalyway Combo Update 10.5.3, or you'll get white menu bugs. Install the package, then install Jas Combo Update 10.5.3 No need for aditional patching, kexts editing etc. Connected to a VGA monitor, using a dvi2vga adapter.
|
Both
|
All Resolutions
|
Works, use ATI Radeon HD.pkg for 3650 version.
|
| ATI Radeon HD 3850
|
Gigabyte
|
Latest Natit.kext and White_menus_fix
|
Yes
|
All Resolutions (Monitor Max @ 1680x1050 on both heads)
|
Doesn't work without patches. Also only cards with BIOS version 102 or earlier work. BIOS version 103 is not yet compatible.
|
| ATI Radeon HD 3850
|
HiS
|
Installer found from irc.osx86.hu channel #radeonhd then White menu fix also from IRC Channel
|
Fully working
|
Yes Up to 1080p 1920x1080
|
No
|
| ATI Radeon HD 3870
|
Sapphire
|
Triakis and latest 38x0 drivers from Leopard-10.5.2-AMD-EFI DVD (netkas's originals work too.)
|
Yes
|
All Resolutions (Monitor Max @ 1680x1050 on both heads)
|
Patches incorporated in Leopard-10.5.2-AMD-EFI DVD or elsewhere obtained netkas/triakis kexts required.
|
| ATI Radeon HD 3870
|
Sapphire
|
Used Natit.kext
|
Both Work
|
All Resolutions
|
Fully working with patch
|
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
| Hardware Name
|
Board-Manufacturer
|
Notes
|
QE / CI
|
Resolution
|
Fully Working w/o Patch
|
| GeForce 6200
|
MSI
|
Works with Natit, NVinject and NVidia kexts bundled with Zephyroth 10.5.2
|
Not Supported
|
Default: 1024x768 Unable to change resolution from System Preferences, changed resolution from boot
|
Partially working with patch (Since QE is not supported)
|
| GeForce 6200TC 512MB
|
XFX
|
Unknown Patch
|
Unknown
|
Unknown
|
Unknown
|
| GeForce 6800GS 256MB
|
PNY
|
Used kexts only from Zephyroth Universal Nvidia Installer,then must manually add device IDs to Geforce.kext, NVDARESMAN, and NVDAR40HAL finall NVinject .21 with instructions in forums. google "nvidia card working in leopard" for more help.
|
QE/CI both work
|
All resolutions work
|
Dual monitor with extended desktop but no mirroring.
|
| GeForce 6800GT 256MB
|
Leadtek
|
No acceleration :( -- too slow and choppy to be useful.
|
No
|
1920x1200 working
|
No
|
| GeForce 6800GT 256MB
|
Leadtek
|
NVinject 0.2.1, manually add device IDs to kexts (Geforce, NVDARE~, NVDAR4~)
|
QE/CI both work
|
1680 x 1050 working fine
|
Fully working with patch. Dual monitor (extended desktop) works using VGA + DVI-to-VGA adapter
|
| GeForce 7100GS 256MB
|
XFX
|
Used NVInject
|
Both
|
Only 1680 x 1050 tested, works great.
|
Fully working with patch
|
| GeForce 7200GS 128MB
|
Asus
|
Nvinkjet bundled in Kalyway 10.5.1
|
Both
|
All resolutions work
|
Fully working with patch
|
| GeForce 7200GS 256MB
|
ASUS
|
NVInject on Kalyway 10.5.2
|
Both
|
Yes
|
Working with patch
|
| GeForce 7200GS 256MB
|
XFX
|
NVInstaller v.4.1
|
QE/CI both work
|
All resolutions work
|
Single display working with patch (10.5.3 works with vanilla NVinstaller v0.52); TV-out does not work at all
|
| GeForce 7200GS 256MB Passive Cooling
|
PNY
|
NVInject
|
Both work
|
All resolutions work
|
Fully working with patch
|
| GeForce 7300 LE (64 MB RAM, 256 MB shared)
|
Asus (OEM'd by HP)
|
NVInject, added to GeForce.kext, and booted with "Graphics Mode"="[email protected]"
|
No Hardware accelleration
|
All resolutions work
|
No QE/CI with patch
|
| GeForce 7300LE 128MB
|
Digital Alliance
|
NVinject 0.2.1 used
|
Yes
|
All resolutions
|
With NVInject
|
| GeForce 7300LE 256MB
|
Leadteck
|
NVInject work fine
|
Yes
|
All resolutions work
|
Fully working with patch (EFI strings recommended)
|
| GeForce 7300GS 256MB
|
Gigabyte
|
NVInject/Natit both work fine
|
QE/CI both work
|
All resolutions work
|
Fully working with patch
|
| GeForce 7300GS 256MB
|
Club3D
|
NVInject on Kalyway
|
Unknown
|
All
|
Fully working with patch
|
| GeForce 7300GS 256MB
|
ASUS
|
NVinject
|
QE/CI both work
|
All resolutions work
|
Fully working with patch
|
| GeForce 7300GS 256MB
|
XFX
|
NVinject
|
QE/CI both work
|
All resolutions work
|
Fully working with patch
|
| GeForce 7300GS 256MB
|
MSI
|
NVinject/NVinstaller 5.2
|
QE/CI both work
|
All resolutions work in both DVI and HDMI ports
|
Fully working with patch
|
GeForce 7300GS 256MB
| Chaintech
|
NVinject 0.2.1
|
QE/CI both work
|
All resolutions work
|
Yes
|
| GeForce 7300GS 256MB
|
Chaintech
|
Kalyway Patch
|
Both
|
All resolutions work
|
Yes
|
| GeForce 7300GT 256MB
|
BIG
|
NVInject
|
QE/CI both work
|
All resolutions work
|
Yes with NVInject
|
| GeForce 7300GT 256MB
|
GIGABYTE
|
NVInject
|
QE/CI both work
|
All resolutions work
|
Yes with NVInject
|
| GeForce 7300GT 256MB Silent Edition
|
NVIDIA
|
NVInject 0.2.0
|
Both
|
All resolutions
|
Yes with NVInject
|
| GeForce 7300GT 256MB
|
eVGA
|
NVInject
|
Both
|
All resolutions
|
Yes with NVInject
|
| GeForce 7300GT 256MB
|
Zotac
|
NVInject
|
Both
|
All resolutions
|
Yes with NVInject
|
| GeForce EN7300GT 256MB
|
ASUS
|
Works with NVinject
|
Both
|
All
|
|
| GeForce 7300GT 512MB
|
Pixelview
|
Card needs to be reflashed first
|
Both
|
All
|
yes, with NVinject 512mb
|
| GeForce 7300 GT 512 Mb (No TurboCache)
|
XFX
|
Used NVInject 512 Mb 0.2.0 (Kalyway OS X86 version, EFI v8), I had to flash my card by following not so simple steps. Visit NVInject Project Website for more information.
|
Both
|
Yes
|
No, I had to flash my card so that Darwin recognizes it as a 512 Mb video card.
|
| GeForce 7500LT 256MB
|
ASUS
|
NVKush, works with NVKush Istaller. VGA and DVI both work.
|
QE/CI work
|
1280 x 1024 works great
|
Fully working with NVKush.
|
| GeForce 7600GS 256MB
|
Point of View
|
Used Titan
|
QE/CI both work
|
All resolutions work
|
Fully working with Titan
|
| GeForce 7600GS 256MB
|
PowerColor
|
NVinject
|
QE/CI both work
|
All resolutions work
|
Fully working
|
| GeForce 7600GT 256MB
|
BIOSTAR
|
- Works with NVinject or EFI string
- (Model: V7603GT21) The stock fan noise is not detectable all the time. One may need to move his hand close enough to the fan to see if it is running.
|
QE/CI both work
|
All resolutions work
|
Fully working
|
| GeForce 7600GT 256MB
|
eVGA
|
- Works with NVinject or EFI string
- (Model: 256P2N553DX) The stock fan gets really noisy during booting (post) and then becomes really quiet. It becomes noisy right before Sleep, and keeps running like so after Wake.
|
QE/CI both work
|
All resolutions work
|
Fully working
|
| GeForce 7600GT 256MB
|
Gigabyte
|
NVinject or Natit
|
QE/CI both work
|
All resolutions work
|
Fully working
|
| GeForce 7600GT 256MB
|
NVIDIA
|
None
|
QE/CI both work
|
All resolutions work
|
Yes
|
| GeForce 7600GT 256MB
|
Winfast
|
NVInject 0.20
|
Both
|
All resolutions work
|
Yes
|
| GeForce 7600GT 256MB
|
Eagle
|
NVinject or Natit
|
QE/CI both work
|
All resolutions work
|
Yes
|
| GeForce 7600GT 256MB GDDR3
|
Zotac
|
NVinject
|
QE/CI both work
|
All resolutions work
|
Yes
|
| GeForce 7600GT-OC VIVO 256MB
|
MSI
|
NVinject or Natit
|
QE/CI both work
|
All resolutions work
|
VIVO doesn't work otherwise fully functional
|
| GeForce 7600GT Silent 256MB
|
MSI
|
NVinject (ASUS P5B-MX), EFI-string using EFIStudio (Gigabyte GA-G31M-S2L)
|
QE/CI both work
|
All resolutions work
|
Needs patch for resolutions and memory detection
|
| GeForce 7600GT 256MB
|
XFX
|
NVinject, Natit or GFX-String
|
QE/CI both work
|
All resolutions work
|
Yes, with NVinject, Natit or GFX-String
|
| GeForce 7600GT 256MB
|
eVGA
|
NNInject 0.1.5
|
QE/CI both work
|
All resolutions work
|
Yes with NVInject
|
| GeForce 7800GT 256MB
|
NVIDIA
|
Kalyway NVIDIA patch
|
Unknown
|
Not all
|
Need patch from Kalyway
|
| GeForce 7800GT OC 256MB
|
BFG
|
NVInject v0.41
|
Unkown
|
All resolutions work
|
Yes with patch
|
| GeForce 7800GTX 256MB
|
ASUS
|
NVInject v0.33
|
Both
|
All
|
Yes with Patch
|
| GeForce 7900GS 256MB
|
NVIDIA
|
Kalyway NVIDIA patch
|
Unknown
|
Not all
|
Need patch from Kalyway
|
| GeForce 7900GT 256MB
|
ASUS
|
Kalyway NVIDIA patch
|
Unknown
|
Not all
|
Need patch from Kalyway
|
| GeForce 7900GT CO 256MB
|
eVGA
|
NVInject
|
QE/CI both work
|
All resolutions work
|
Need to use NVInject
|
| GeForce 7900GTO 512MB
|
MSI
|
NVInject, Needs Bios Flash, Check here for rom.
|
QE/CI both work
|
All resolutions work, TV Out untested
|
Need to use NVInject, BIOS flash
|
| GeForce 7950 512MB
|
eVGA
|
NVInject
|
Unknown
|
All resolutions work
|
Need to use NVInject
|
| GeForce 7950GT 512MB
|
NVIDIA
|
Needs 4 bytes of bios changed and reflashed. Used this guide and windows nvflash.
|
QE/CI both work
|
All resolutions work (only 60hz working though)
|
Used NVinject 2.0 and followed guide here for kext setup.
|
| GeForce 7950GTOC 512MB
|
BFG
|
Needs Bios Flash, Check here for rom.
|
QE/CI both work
|
All resolutions work
|
Can use Nvinject or without if you have efi installed by following guide to create gfx string here
|
| GeForce 8400GS 256MB
|
Gigabyte
|
Works with NVinject 0.2.1, NVCAP string with 04000000 00000300 04000000 00000007 00000000 for DVI.
|
QE / CI , yes all
|
Resolution , yes all
|
Fully Working with Patch
|
| GeForce 8400GS 256MB
|
MSI
|
NVinject 0.2.1 here. EFI GFX Strings work following this guide.
|
QE/CI both work
|
All resolutions work
|
No QE/CI without patch
|
| GeForce 8400GS 256MB
|
XFX
|
NVinject 0.2.0 during Kalyway 10.5.2 install (choose Nvidia 256MB)
|
QE/CI both work
|
All resolutions work
|
No QE/CI without patch (NVinject 0.2.0 during Kalyway 10.5.2 install)
DVI output needs NVCAP edit:
- Right Click /System/Library/Extensions/NVInject.kext choose "Show Package Contents"
- Copy Info.plist to ~/Desktop
- Open Info.plist copy with Plist Editor
- Replace NVCAP string with 04000000 00000300 04000000 00000007 00000000
- Save copy of info.plist and copy back to NVInject.kext contents
|
| GeForce 8400GS 256MB
|
XFX
|
NVinject 0.2.1 here
|
QE/CI both work
|
All resolutions work
|
No QE/CI without patch
|
| GeForce 8400GS 512MB
|
XFX
|
NVinject 0.2.0 during Kalyway 10.5.2 install
|
QE/CI both work
|
All resolutions work
|
No. DVI output needs NVCAP edit. 04000000 00000300 04000000 00000007 00000000 worked.
|
| GeForce 8400GS 256MB
|
Club3D
|
NVinject 0.2.0 after Kalyway 10.5.2 install (don't use 0.2.1)
|
QE/CI both work
|
All resolutions work
|
DVI not tested
|
| GeForce 8400GT 512MB
|
eVGA
|
Works with NvInject
|
Unknown
|
All resolutions work
|
Yes
|
| GeForce 8500GT 256MB
|
GIGABYTE
|
NvInject 0.2.1
|
QE/CI both work
|
Yes, correct widescreen res for analog only with VGA-DVI converter.
|
Yes, with patch
|
| NX8500GT MTD256EH
|
MSI
|
Leo4Allv2, NvInject 0.2.1 (256MB)
|
QE/CI both work
|
All resolutions. Dual DVI with HDMI-DVI cable + DVI
|
Yes
|
| GeForce 8500GT 512MB
|
GALAXY
|
NvInject 0.2.1 with 512MB patch
|
QE/CI both work
|
All resolutions work.
|
Yes, with patch
|
| GeForce 8500GT 512MB (SILENT)
|
Sparkle
|
NvInject 0.2.0 (256MB Recognized)
|
QE/CI both work
|
All resolutions + DVI-I
|
Yes, with patch
|
| Nvidia GeForce 8600M GS 512MB
|
NVidia
|
Display requires driver installation and modification of info.plist to work at full resolution and with VGA-out. Mirror function still doesn't work properly, but forces main display to VGA-out.
- Install Universal NVidia Driver (http://zack.phatoproductions.com/downloads/mac/NVidia-Universal-Installer.mpkg.rar)
- Right Click /System/Library/Extensions/NVInject.kext choose "Show Package Contents"
- Copy Info.plist to ~/Desktop
- Open Info.plist copy with Plist Editor
- Replace NVCAP string with 04000000 00000100 02000000 00000007 00000000
- Save copy of info.plist and copy back to NVInject.kext contents
- Change permissions of NVInject:
"sudo chown -R root:wheel /System/Library/Extensions/NVinject.kext"
"sudo chmod -R 755 /System/Library/Extensions/NVinject.kext"
- Run Disk Utility and repair permissions on disk.
- Delete Extension Caches and Kernel Caches before rebooting
"sudo rm -R /System/Library/Extensions.mkext /System/Library/Extensions/Caches/"
- Reboot with -f just in case.
|
Yes with Driver
|
No: 1024x768 w/out driver
All Resolutions and VGA-out with Driver
|
Partial at 1024x768
|
| GeForce 8600GT 256MB FATAL1TY
|
XFX
|
NvInject 0.2.1 (256MB)
|
QE/CI both work
|
All resolutions work
|
Yes With Patch
|
| GeForce 8600GT 256MB Zalman
|
XFX
|
NVinstaller v.41. It works perfectly on PCIe 16x mobo (but doesn't work on PCIe 4x mobo like asrock 4coredual-sata2 for instance)
|
QE/CI both work
|
All resolutions work + dual screen
|
Yes with NVinstaller v.41
|
| GeForce 8600GT 256MB
|
EVGA
|
Used bf2loser's guide from here
|
QE/CI/GL both work, sleep (standby) works, Dual Monitor works, no mirroring
|
All resolutions work
|
Yes With Patch (Punk92) + guide (bf2loser)
|
| GeForce 8600GT 256MB
|
Elsa Gladiac
|
Used 10.5.2 patch
|
Unknown
|
All resolutions work
|
Unknown
|
| GeForce 8800GS 384MB
|
eVGA
|
NVInstaller .41
|
QE/CI work
|
All Resolutions work
|
Just edit the DeviceIDs in kexts.
|
| GeForce 8600GT 1024MB
|
Gainward
|
NVInstaller v.41
|
QE/CI work
|
All resolutions work
|
Yes, with patch but only 768MB and not 1024MB
|
| Nvidia GeForce 8800GT 512MB (G92)
|
XpertVision
|
NVInstaller v.33 (NVinject v0.2.1)
|
QE/CI both work
|
All resolutions work
|
Yes
|
| GeForce 8800GT 256MB
|
XFX
|
NVinstaller0.33
|
QE/CI both work
|
All resolutions work
|
Yes, with patch
|
| GeForce 8800GT 256MB
|
ASUS
|
NvInstaller 3.1 Used
|
QE/CI both work
|
All resolutions work
|
Yes, with patch
|
| GeForce 8600GT 512MB
|
MSI
|
Used johnniecarcinogen's NVInstall 0.33 to enable full features
|
QE/CI both work
|
All resolutions work
|
Patch needed
|
| GeForce 8600GT 512MB
|
XFX
|
Working OOB, install NVinject V41 AFTER INSTALL to enable all resolutions and other features.
|
QE/CI both work
|
All resolutions work
|
Patch needed
|
| GeForce 8600GT 256MB XXX
|
XFX
|
NVinject
|
QE/CI both work
|
All resolutions work
|
Yes
|
| GeForce 8600GTS 256MB / 512MB
|
NVIDIA
|
Install in order, and clear kextcache / repair permissions after each step:
Leopard Graphics Update 1.0 -> NVInstaller v.41 -> Erase and change Device IDs (GeForce.kext, NVDANV##Hal.kext, NVDAResman.ext, NVinject.kext) to "040010de".
|
QE/CI both work
|
All resolutions work
|
Yes
|
| GeForce NX8800GT 512MB
|
MSI
|
NVInstaller V.34 here
|
Both
|
All
|
Just great!
|
| GeForce 8800GT 512MB
|
Asus
|
Apple graphics update 10.5.2+NV 41.
|
Both
|
All
|
Just great!
|
| GeForce NX8800GT 512M OC
|
MSI
|
NVinject
|
QE/CI both work
|
All resolutions work
|
Flawless
|
| GeForce 8800GT 512MB Turbo
|
Gigabyte
|
NVinject
|
QE/CI both work
|
All resolutions
|
Yes
|
| GeForce 8800GT 512MB (G92)
|
Gigabyte
|
EFI Strings & EFI v8 used. Works after Leopard Graphics Update
|
QE/CI both work
|
All resolutions work
|
| eGeForce 8800GT KO 512MB (G92)
|
eVGA
|
NVInstaller v.33 (NVinject v0.2.1)
|
QE/CI both work
|
All resolutions work
|
Yes, needs NVinject v0.2.1, works post applegfx update
|
| GeForce 8800GTS 256MB
|
NVIDIA
|
Works with BrazilMac
|
QE/CI both work
|
All resolutions work
|
Yes
|
| GeForce 8800GTS 320MB
|
MSI
|
NVinject here
|
QE/CI both work
|
All resolutions work
|
Needs patch for resolutions and memory detection
|
| GeForce 8800GTS 320MB
|
PNY
|
NVinject here
|
QE/CI both work
|
All resolutions work
|
Needs patch for resolutions and memory detection
|
| GeForce 8800GTS 320MB
|
EVGA
|
NVinject here
|
QE/CI both work
|
All resolutions work
|
Needs patch for resolutions and memory detection
|
| GeForce 8800GTS 320MB XXX Edition
|
XFX
|
NVinject-320
|
QE/CI both work
|
All resolutions work
|
Yes, I used Kalyway 10.5.2 DVD with NVinject-320
|
| GeForce 8800GTS 512MB
|
XFX
|
NVinject installer v.33
|
QE/CI both work
|
All resolutions work
|
No
|
| GeForce 8800GTS 512MB (G92)
|
ASUS
|
NVinject.0.2.1 here
|
QE/CI both work
|
All resolutions work
|
Yes, needs NVinject v0.2.1 and VRAM,totalsize has to be set manually in "info.plist" to <00000020> - 512Mb
|
| GeForce 8800GTS 512MB (G92)
|
eVGA
|
NVinstaller v4.1
|
QE/CI both work
|
All resolutions work
|
Had to add 0x0600 (Device ID) to GeForce NVDANV50Hal, NVDAResman, NVinject kexts.
|
| GeForce 8800GTS 512MB (G92)
|
Point of View
|
NVinstaller v0.33
|
QE/CI both work
|
All resolutions work (using 1920x1200)
|
Yes, just used NVInstaller v0.33, download here: http://scottdangel.com/blog/?page_id=20
|
| GeForce 8800GTX 756MB
|
ASUS
|
NVInject 768MB on Zerpyroths 10.5.2 release
|
Both
|
All
|
Yes w/ NVinject
|
| GeForce 8800GTX 756MB (G80)
|
ASUS
|
NVinject 0.2.0
|
Both
|
All
|
Yes w/ NVinject
|
| GeForce 9800GTX 512MB (G92)
|
Evga
|
GFX Strings
|
Both
|
All resolutions work (using 1920x1200)
|
Installation instruction here
|
| GeForce 9800GTX 512MB (G92)
|
Leadtek
|
GFX Strings & EFI v.8
|
Both
|
All showing in System Preferences>Display; but only 1680x1050 tested (my LCD native)
|
Best results with GFX Strings method described by aquamac here
|
| nVidia Quadro FX 1400 (128Mb)
|
HP
|
Kalyway Release 10.5.2 & NVinject 0.2.0 &
|
Both
|
All resolution work include Dual View Display
|
Patch needed in insanelymac forum (change deviceID in GeForoce.kext, NVIDANV40HAL.kext, NVinject.kext)
|
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .
| Interface
|
Standard
|
Device
|
Manufacturer
|
Notes
|
Fully Working w/o Patch
|
| PCI Card
|
802.11bg
|
ALL0281
|
Allnet
|
Atheros Chipset, Working using this post (kexts from 10.4.8) Manufacturer ID: 168c Device ID: 0013; connect on startup with a small script
|
No
|
| Mini PCI Express Card
|
802.11abg
|
AR5BXB6
|
Atheros
|
Working
|
Working on Kalyway's 10.5.1 with 10.5.2 update
|
| PCI Card
|
802.11b/g
|
F5D7000
|
Belkin
|
Working with Broadcom 43xx Patch included on Zephyroth DVD. Regular dropouts, cause unconfirmed.
|
With patch
|
| PCI Card
|
802.11b/g
|
DX-BGDTC
|
Dynex
|
Working with Broadcom 43xx Patch.
|
With patch
|
| PCI Card
|
802.11b/g
|
DWL-G510 (rev. A)
|
D-Link
|
For Atheros chip, use this guide: http://forum.insanelymac.com/index.php?showtopic=100551&st=0&p=717143&#entry717143
|
No
|
| PCI Card
|
802.11b/g
|
DWL-G520 rev.b
|
D-Link
|
AR5213 Chipset. working using guide from http://forum.insanelymac.com/index.php?s=&showtopic=40317&view=findpost&p=780131. remember to first type sudo -s in terminal before entering code and repair disk permissions afterwards. WPA not working? - please confirm. used Leo4all v3
|
No
|
| PCI Card
|
802.11b/g
|
HWP-54G
|
Hawking
|
Used RT2500 "STA_CardbusPCI" Driver & Utility from Ralink Website - the Tiger version (dated 11-23-2006). Does not show up in System Profiler at all, but works if you disable ("Make Service Inactive") the wired ethernet port (en0). Also this was on an unmolested Kalyway 10.5.2 DVD Install.
|
No. Requires Driver, Utility, Settings tweaks.
|
| PCI Card
|
802.11b/g/n
|
EW7728In
|
Edimax
|
Works beautifully using the Ralink 10.5 drivers at: http://www.ralinktech.com.tw/data/drivers/STA_RT2860%20D-1.0.0.0a%20UI-1.4.8.0_2007_11_26.dmg
Doesn't connect as Airport, and must be configured using the Ralink Utility; configured as ethernet. Occasional dropouts, but cause unconfirmed. As a side note, this card works perfectly in Vista x64 as well, n-mode all the way!
|
No, see notes
|
| PCI Card
|
802.11b/g/n
|
ENLWI-N
|
Encore
|
Works using Ralink 10.5 drivers http://www.ralinktech.com.tw/data/drivers/STA_RT2860%20D-1.0.0.0a%20UI-1.4.8.0_2007_11_26.dmg
|
Yes
|
| PCI Card
|
802.11b/g
|
WMC300N
|
Linksys
|
Working OOB
|
Yes
|
| PCI Card
|
802.11b/g/n
|
TEW-623PI 1.0R
|
Trendnet
|
Working OOB
|
Yes
|
| PCI Card
|
802.11b/g/n
|
TEW-623PI 2.0R
|
Trendnet
|
Apparently Trendnet changed their wireless chipset in the 2.0 version of the card to Ralink RT2860. Card works if you use the drivers here Note: if you are going to buy this card off newegg you will get the 2.0 version as of 7/25/08. Also of note the ralink software is a bit clunky compared to apple's airport setup in the system prefs.
|
No, see note.
|
| PCI Card
|
802.11n/g/b
|
WMP300N
|
Linksys
|
Works OOB with Kalyway 10.5.1, requires 10.5.1 kexts (IO80211Family, IONetworkingFamily, IOPCIFamily) to work with Kalyway 10.5.2. Won't run in Vista x64. Uses an Atheros 5008 chipset.
|
No
|
| PCI Card
|
802.11 a/b/g/n
|
WMP300N rev.2
|
Linksys
|
Working OOB, recognized as an Apple Wireless Network Adapter. WiFi n Works fine and fast. Works also With Vista 64Bits.
|
Out of the Box
|
| PCI Card
|
802.11g
|
WMP54GS v1.0
|
Linksys
|
Working out of the box both Kalyway 10.5.1 & iAtkos v1.0i; detected as Third Party Wireless Card
|
Yes
|
| PCI Card
|
802.11g
|
WMP54GS v1.1
|
Linksys
|
Working OOB, detected as Airport
|
Yes
|
| PCI Card
|
802.11b/g
|
WMP54G v4.0
|
Linksys
|
Working with Ralink rt2500 drivers & utillity
|
Yes
|
| PCI Card
|
802.11b/g
|
WMP54G v4.1
|
Linksys
|
Not Working
|
No
|
| PCI Card
|
802.11g
|
WG311T
|
Netgear
|
Working after adding device ID "pci168c,13" in original AirPortAtheros.kext
|
No
|
| PCI Card
|
802.11g
|
WG311v3
|
Netgear
|
Not working. Card has a marvell 8335 chipset.
|
No
|
| PCI Card
|
802.11bg
|
WG311T
|
Atheros
|
Working using this post (kexts from 10.4.8) Manufacturer ID: 168c Device ID: 0013
|
Working on Kalyway's 10.5.1 with 10.5.2 update
|
| USB Adapter
|
802.11g
|
WG111v3 (Realtek's RTL8187 Chipset)
|
NETGEAR
|
Detected as an Ethernet Controller with RTL8187B Drivers from http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=1&PFid=1&Level=6&Conn=5&DownTypeID=3&GetDown=false&Downloads=true, and working perfectly!
|
Working with driver
|
| USB Adapter
|
802.11g
|
WG111v2 (Realtek's RTL8187 Chipset)
|
NETGEAR
|
Detected as an Ethernet Controller with RTL8187L Drivers from HERE, and working perfectly!
|
Working with driver
|
| USB Adapter
|
802.11g
|
Wireless G USB (v4001 Zydas Chipset)
|
BELKIN
|
Working perfectly with drivers from http://mac.softpedia.com/get/Drivers/Zydas-WLAN-USB-driver.shtml on Leo4Allv2
|
Yes working with drivers
|
| USB Adapter
|
802.11bgn
|
F5D8053
|
BELKIN
|
Working perfectly with drivers you can get from Totallybonkers here : http://www.mac-forums.com/forums/showthread.php?p=685772#post685772 . Only tested with a 802.11g network with WEP.
|
Yes working with drivers
|
| USB Adapter
|
802.11b/g
|
WL-167g
|
ASUS
|
First install Realtek Drivers from http://www.ralinktech.com/ralink/Home/Support/Macintosh.html (USB RT2870) Restart with -f and -v look for a ralink driver being loaded. Then go to Network in System Preferences, hopefully it will appear. Start USBWirelessUtility and check for the device status. If it doesn't work, check that the RT73USBWireless.kext is really loaded. In terminal kextstat, and look for com.Ralink.driver.RT73 (1.1.7). If it isn't there try sudo kextload RT73USBWireless.kext in terminal. You might also have to add your ip settings manually in Network Preferences by clicking the plus sign above the lock and adding an ethernet device.
|
It works ok now but i get some CRC errors and dropped frames, according to USBWirelessUtility. But i did download 4 gb torrents just fine...
|
| PCI Card
|
802.11g
|
F5D7000
|
Belkin
|
Working with Zephyroth 10.5.2, select Broadcom 43xx series drivers when customising the install
|
Patches are on Zephyroth Install DVD
|
| PCI Card
|
802.11a/b/g
|
AWLH4030
|
Airlink
|
Working with 10.5.2 using AirportAtheros5424.kext. Had to remove all device/manufacturer id's except the one for the specific card. [168c:0013]
|
No
|
| PCI Card
|
802.11n
|
AWLH6080
|
Airlink
|
Working with 10.5.2 using Ralink driver. Connection utility kept hanging Shutdown until I cleared system caches. Cheap $45 Draft N card.
|
Yes
|
| PCI-Express Card
|
802.11n
|
DWA-556
|
D-Link
|
Working with Kalyway 10.5.1 and 10.5.2 out of box, detected as Airport Extreme. Note: sometimes drops connections, could be due to other OSX issues. Sleep function now also works out of the box, without the modified kernel - I have previously used the WG311T, and it didn't work.
|
Yes. Keep in mind, you must not use the modified IO80211Family.kext.
|
| USB Adapter
|
802.11 b/g
|
DWL-G122 Version C1
|
D-Link
|
Working. Known issue: after each reeboot of OSX you need to re-insert the USB adapter in order to be correctly detected by the OS.
|
Working on Kalyway's 10.5.1 with drivers supplied in Dlink's CD.
|
| USB Adapter
|
802.11 b/g
|
WUSB54GC
|
Linksys
|
Working on Kalyway's 10.5.2 DVD installation using the following steps: a. Install Prasys drivers on Kalyway 10.5.1 with WUSB54GC working. b. Use Kext Helper b7 to install 10.5.1 IO80211Familykext and 3 RT* kext. c. Install Prasys 1.2 utility.
|
Yes, with replug
|
| USB Adapter
|
802.11 b/g
|
TEW-424UB V3.0R & V3.1R
|
TrendNet
|
Working with Kalyway 10.5.2 DVD and driver from Realtek. Device Versions V3.0R and V3.1R use RTL8187B chipset, Versions V2 and V2.1R use SIS163. The original version A used the Zydas chipset.
|
Yes, but with extra driver
|
| USB Adapter
|
802.11g
|
US54SE II (Realtek's RTL8187 Chipset)
|
MSI
|
Detected as an Ethernet Controller with RTL8187L Drivers from HERE, and working perfectly!
|
Working with driver
|
| USB Adapter
|
802.11g
|
Wi-Fire
|
hField Technologies
|
Uses their own wi-fi management utility. They have updated drivers at their website. This adapter is available retail at Microcenter and online at Amazon, Newegg, etc. As of June 08, runs ~$70. Works fine with manufacturer supplied drivers, good network pickup on directional receiver.
|
Working with manufacture supplied OSX 10.4/10.5 driver!
|
| PCI Card
|
802.11b/g
|
USR5417
|
U.S. Robotics
|
Works Out of Box, detected as Airport.
|
Yes
|
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
