HCL 10.9.3

Latest revision as of 01:43, 8 November 2014

macOS 10.9.3
Hardware Compatibility

Portable Computers
Desktop Computers
Hardware Components

This is a component level hardware compatibility list. We want to keep it as accurate as possible, but please, do not entirely rely on this list when buying hardware. Add which parts you have working in the categories listed below, or create a new category. Please keep alphabetical order inside the categories. The categories themselves are ordered by popularity. Please list any caveats or problems as well.

ONLY add hardware that you have TESTED. Don't add hardware just because you think it might work.
Please add hardware into tables.
This is for 10.9.3 builds only.

For how to edit the Wiki, please see this thread. Thank you!

You're looking for an Installation guide? see here

Note: For suggestions about table headings, please join the discussion here.

[edit] Motherboards

[edit] Abit

Hardware Name	Chipset	Notes	Patches Used	Compatible 64bit

[edit] Alienware

Hardware Name	Chipset	Notes	Patches Used	Compatible 64bit

[edit] Asrock

Hardware Name	Chipset	Notes	Patches Used
B85M-Pro4	Intel B85	System Configuration: CPU: Core i3 4130 GPU: Saphire HD5450 512MB Bios settings Version: 1.90 Virtualization disabled primary graphics: pci-e legacy mode Installation: AppStore Mavericks app (10.9.3) SMBios: iMac14,2 USB created myHack 3.3.1 (no MBR patch) patched mach_kernel System Status: AMD Graphics: QE, full 3D acceleration Intel IGP Graphics - not tested! Audio Ethernet USB 3.0 Sleep, Shutdown, Restart	Post-installation: Kernel -> directly after installation replace mach_kernel (HDD) with patched kernel (MyHack USB) through Terminal.app Audio -> ALC892 Network -> Intel I217v - AppleIntelE1000e.kext patch Device ID (0x68f91002) in AMD5000Controller and ATIRadeonX3000. Chameleon Boot Flags: GraphicsEnabler=No Extra / Extensions: AppleIntelE1000e.kext FakeSMC.kext lspcidrv.kext Patched_10.7_AppleRTC.kext
Z77 Pro-4	Intel Z77	System Configuration: CPU: Intel Core i5 3550 Ivy bridge with oc @ 4100 Mhz (3300 mhz stock freq.) RAM: 1x4GB Kingston 1333 MHz overklocked @ 1800 mhz VGA: ASUS GeForce® 210 EN210 SILENT/DI/1GD3/V2(LP) ETH: 1x Realtek RTL8111E gigabit lan WIFI: Icidu 150N pci-e card, with atheros ar9285 chip SND: Onboard ALC892 System Status: All of the above components: Reboot, Shutdown: Sleep: Works:	Installation method: Pendrive with Mavericks downloaded from App Store and Niresh.co extra's Boot flags: ncpi=0x3000 GraphicsEnabler=Yes UseKernelCache=Yes VT-d disabled, Sata on AHCI mode Graphics - Worked OOB Network - Worked OOB WIFI - Works when using this kext USB - Worked OOB USB 3.0 - Worked OOB SATA - Worked OOB App Store - Worked OOB Sound - Works when using VoodooHDA kext Kernel - Vanilla Mach_kernel
Z87 Fatal1ty Professional	Intel Z87	System Configuration: CPU: Intel Core i7 (Haswell) 4770K @3.5GHz RAM: 16GB (4x4GB) Kingston 1333MHz VGA: Gigabyte GeForce GTX760 WindForce 2GB ETH: 1 x Intel I217-V, 1 x Intel I211 SND: Creative Sound Core3D BIOS: 1.90 System Status: All of the above components: * (See Notes) Reboot, Shutdown: (OOB) Sleep/Wake: (OOB)	Installation method: USB 10.9.3 from App Store prepared on existing Macbook Pro Notes Boot flags: npci=0x1000 Virtualization, CPU powers states all enabled in BIOS Graphics - (OOB) Ethernet (I217-V) - (OOB) Ethernet (I211-V) - Not Detected USB - (OOB) USB 3.0 - (OOB) SATA - (OOB) App Store - (OOB) Sound - (With latest VoodooHDA) Kernel - (OOB)

[edit] Asus

[edit] Biostar

Hardware Name	Chipset	Notes	Patches Used
M5A78L-M LX3	AMD 760(780L)/SB710	System Configuration: CPU: AMD FX-6100 @3.3 Ghz GPU: Nvidia GeForce G210 RAM: 2x4GB 1600Mhz HDD: Seagate Barracuda 1Tb Bios settings: AHCI Suspend Mode S3 Installation: AppStore Mavericks app (10.9.3) update from 10.9.2 System Status: Graphics: QE, full 3D acceleration DVI VGA Audio -> USB Hercules Djconsole 4-MxEthernet TimeMachine, App Store Sleep, Wakeup, Poweroff	Post-installation: Kernel and kexts -> AMD Kernel Mavericks 10.9.3 Network -> Qualcomm Atheros 8161Gb LAN Kext
P9X79 LE	X79	System Configuration: CPU: Intel i7 3820 @ 3.6GHz GPU: Asus 650 Ti 1024Mb RAM: 32Gb Corsair XMS3 HDD: SSD 64Gb Installation: AppStore Mavericks app (10.9.3) update from 10.9.2 System Status: Graphics: Native, works fine Audio: ALC892 (patched) TimeMachine, App Store, iMessage, Facetime Sleep, Wakeup, Poweroff USB 3.0	Post-installation: Realtek kext ALC892 + HDAEnabler1 + Applications/Utilities/Audio Midi Setup - change the Frequency from 44100hz to 48000hz
P5W DH Deluxe	Intel 975X	System Configuration: CPU: Intel® Pentium® Processor E5300 (2M Cache, 2.60 GHz, 800 MHz FSB) (Overclock 3.48 GHz BUS 266x13 1066 MHz FSB) GPU: SAPPHIRE HD 5770 1024MB DDR5 PCIE http://www.sapphiretech.com/presentation/product/product_index.aspx?pid=341&lid=1 (I'm using it with Dual Displays Full HD) RAM: Slot 2x1GB DDR2 OCZ Platinum rev2 800Mhz 4-4-4-12 2,1v Dual Gigabit LAN Marvell Yukon 88E8053 Gigabit Ethernet Adapter Enabled Natively Keyboard: Apple Wired aluminum keyboard USB Mouse: Logitech MX™ Revolution Cordless Laser Mouse System Status: All Works, Sleep, Wakeup, Shutdown, Restart, Updates and app Through MacAppStore SAPPHIRE HD 5770 1024 MB (Install kext PIEROF81Inject.kext Edited by me) Full Works + Dual DVI_HDMI_Display Port Yes	Patches: Chameleon-2.2svn-r2246.pkg Kexts (FakeSMC,NullCPUPowerManagement,HDAEnabler+AppleHDA for Realtek ALC full sound of 882m, ICH7_Jmicron363 (Edited by me) for the correct information on System Profiler) DSDT For HDMI/DisplayPort Sound Sapphire HD 5770 and AppleHPET Fix to Firewire 400, USB 2.0 Original Bios v.3001

Hardware Name	Chipset	Notes	Patches Used	Compatible 64bit

[edit] EVGA

Hardware Name	Chipset	Notes	Patches Used	Compatible 64bit

[edit] Foxconn

Hardware Name	Chipset	Notes	Patches Used	Compatible 64bit

[edit] Gigabyte

Hardware Name	Chipset	Notes	Patches Used
GA-Z97X-Gaming GT	Intel® Z97 Chipset	System Configuration: CPU: Intel Core i7 4770k @3.9 GHz GPU: internal Intel HD4600 + Nvidia EVGA GTX760 ACX 4GB GDDR5 RAM: Kingston Hyper RAM 2x8GB 2400 Mhz Component Status: Graphics: Nvidia EVGA GTX760 QE, full 3D acceleration DVI HDMI Dual Monitors Ethernet: Qualcomm® Atheros Killer E2201 LAN chip (10/100/1000 Mbit) Audio: Realtek® ALC1150 codec USB 3.0 Bluetooth TimeMachine, App Store, iMessage, Facetime Sleep, Wakeup, Poweroff	BIOS changes: Sata mode is AHCI Vt-D is disabled Installation Method: tonymacx86 DSDT Free GraphicsEnabler "No" GeneratePStates "Yes" GenerateCStates "Yes" HDAEnabler "Yes" IGPEnabler "Yes" HDEFLayoutID "01000000" Post-Installation: Audio: Realtek® ALC1150 codec
GA-Z97M-D3H	Intel® Z97 Chipset	System Configuration: CPU: Intel Core i5 4570 @3.4 GHz GPU: internal Intel HD4600 + Nvidia EVGA GTX760 ACX 2GB GDDR5 RAM: 4x4GB 1600Mhz HDD: Samsung 840 EVO 120GB SSD + 2 x Western Digital Caviar 2Tb Component Status: Graphics: Nvidia EVGA GTX760 QE, full 3D acceleration DVI HDMI Dual Monitors Ethernet Audio: ALC892 USB 3.0 TimeMachine, App Store, iMessage, Facetime Sleep, Wakeup, Poweroff	BIOS changes: Sata mode is AHCI Vt-D is disabled Installation Method: tonymacx86 Post-Installation: DSDT Free + TRIM
GA-Z97M-D3H	Intel® Z97 Chipset	System Configuration: CPU: Intel Xeon 1231v3 GPU: HIS Radeon R9 270X RAM: 2x4GB 2000Mhz HDD: Samsung 840 EVO 120GB SSD Component Status: Graphics: HIS Radeon R9 270X (OOB) QE, full 3D acceleration DVI HDMI Dual Monitors Ethernet Audio: ALC892 USB 3.0 TimeMachine, App Store, iMessage, Facetime Sleep, Wakeup, Poweroff	BIOS changes: Sata mode is AHCI Vt-D is disabled Installation Method: tonymacx86 Post-Installation: DSDT Free + TRIM + Sound Patch
GA-Z87N-WIFI (rev. 2.0)	Intel® Z87 Chipset	System Configuration: CPU: Intel Core i7 4770K @ 3.5 GHz GPU: Integrated Intel HD4600 + nVidia EVGA GTX750 Ti SSC 1GB GDDR5 RAM: 2 x 8GB Crucial 1.35V DDR3 1600MHz (BLS8G3D1609ES2LX0) HDD: Samsung 830 256GB SSD + Western Digital Green 3TB Component Status: Graphics: Intel HD4600: Disabled, untested. nVidia GTX 650 Ti: 3 monitors (2560x1440 via DVI-DL, 1920x1200 via DVI, 1920x1200 via mini-HDMI). Ethernet: Intel I217-V GbE (LAN1) Works. Atheros GbE (LAN2): Disabled, untested. Audio: ALC892: Disabled, untested. Fiio E17 USB DAC working. USB 3.0: Working. Time Machine: Working. App Store: Working. iMessage / Facetime: Untested.	BIOS changes: SATA mode: AHCI VT-x: Enabled - VT-d is not supported on i7 4770K. XHCI: Auto XHCI / EHCI Handoff: Enabled Installation Method: Clover using FakeSMC.kext, AppleIntelE1000e.kext, GenericUSBXHCI.kext, and config.plist with following main parameters: ACPI: SSDT, CpuPm, DropOem false. Boot: Arguments "npci=0x3000 darkwake=0", Secure false, XMPDetection false. Devices: Audio Inject false. KernelAndKextPatches: AppleAHCIPort (external drives), IOAHCIBlockSTorage (TRIM), AppleTyMCEDriver (MacPro5,1 w/o ECC RAM). SMBIOS: ProductName "MacPro5,1" + associated fields (BiosReleaseDate, BiosVersion, BoardSerialNumber, SerialNumber, SmUUID with MAC as last segment). SystemParameters: InjectKexts true (, InjectSystemID true. Post-Installation: Install Clover to EFI partition on SSD and copy over config.plist and kexts. Install nVidia drivers for 10.9.3 (334.01.01f01).
GA-H87M-D3H	Intel® H87 Chipset	System Configuration: CPU: Intel Core i5 4570 @3.4 GHz GPU: internal Intel HD4600 RAM: 1x4GB 1600Mhz HDD: Kingston 120 GB SSD Component Status: Graphics including HDMI ok Ethernet ok USB 3.0 ok App Store&imessage ok Sleep, Wakeup, Poweroff ok	BIOS changes: xHCI mode is auto xHCI and EHCI Hand-off is enabled Vt-D is disenabled Installation Method: Myhack Method; bootflag; -v -x Post-Installation: ALC892, RealtekRTL81xx v0.0.90 ,TRIM, NullCPU
GA-EP45-UD3P	North Bridge: Intel® P45 Express Chipset South Bridge: Intel® ICH10R	System Configuration: CPU: Intel Core 2 Quad Q8400 @2.66 GHz GPU: ATI Radeon HD 6770 RAM: 4x2GB 800 MHz HDD: Samsung 840 EVO 250GB + 1TB Western Digital Caviar Blue in Fusion Drive Component Status: Graphics including HDMI ok Ethernet ok USB ok App Store ok iMessage Not working yet Sleep displays go off but PC keeps running Wakeup, Poweroff ok Sound Will break after App Store upgrade from 10.9.2 AppleTyMCEDriver.kext removed after upgrade trough the recovery partition due to kernel panic	BIOS changes: Sata mode is AHCI Vt-X is enabled Installation Method: Myhack Method; manually install Chamelon bootloader to the boot partitions of BOTH disks Post-Installation: ALC889, RealtekRTL81xx v0.0.90 ,TRIM, silent boot, custom DSDT, restart fix, ati config set to Bulrushes

[edit] Intel

Hardware Name	Chipset	Notes	Patches Used	Compatible 64bit

[edit] MSI

Hardware Name	Chipset	Notes	Patches Used	Compatible 64bit
B75MA-E33	Intel® B75	System configuration: CPU: Intel Celeron G1610 (2.6 GHz) GPU: Palit NV GT640 1Gb RAM: Corsair 8Gb CMV8GX3M1A1333C9 DDR3 HDA: Realtek ALC887 NIC: Realtek RTL8169 HDD: OCZ Vertex 4 128Gb BIOS Settings: Load Optimized settings Patched Bios Installation method: App Store 10.9.0 InstallESD.dmg USB Installation NVIDIA kexts from 10.9.2 taken here to avoid no signal NV issue System Status: Graphics: QE, full 3D acceleration, native resolution, DVI monitor detected correctly Audio Ethernet USB 2.0 USB 3.0 TimeMachine, App Store Sleep, Wakeup, Poweroff	Post-installation: DSDT-Free Audio -> Realtek ALCxxx -> Without DSDT -> ALC 887/888b -> Current + HDAEnabler Network -> Lnx2Mac's RealtekRTL81xxx System definitions -> MacPro3,1 (default) Chameleon Bootloader FakeSMC NVIDIA Web driver installed
MSI P-31/W8	Intel® H61 B3	System configuration: CPU: Intel Core i3 - 3220 (3.3GHZ Ivy Bridge) GPU: Asus Geforce GT630 2GB Silent RAM: Kingston 4GB HDA: Realtek ALC887 NIC: Realtek 811x HDD: Western Digital 500GB Caviar Blue BIOS Settings: Just change SATA mode to AHCI Installation method: App Store 10.9.0 InstallESD.dmg USB Installation NVIDIA Card works OOB but just in case install this here System Status: Graphics: QE, full 3D acceleration, native resolution, DVI/HDMI monitor detected correctly Audio Ethernet USB 2.0 USB 3.0 TimeMachine, App Store Poweroff	Post-installation: DSDT-Free Audio -> Realtek ALCxxx -> Without DSDT -> Universal -> (Any versions of VoodooHDA after v.2.72)Reason: HDAEnabler version doesn't detect front panel jacks Network -> Lnx2Mac's RealtekRTL81xxx System definitions -> MacPro5,1 Clover Bootloader (Be sure to check "Install Clover on UEFI motherboards) FakeSMC "Info" Sleep works a bit properly cous it can wakeup but mouse will freeze after that.

[edit] PCWARE

Hardware Name	Chipset	Notes	Patches Used	Compatible 64bit

[edit] QUO

Hardware Name	Chipset	Notes	Patches Used	Compatible 64bit

[edit] Supermicro

Hardware Name	Chipset	Notes	Patches Used	Compatible 64bit
X9SRA	C602	System configuration: Motherboard: Supermicro X9SRA motherboard CPU: Intel Xeon E5-2620 RAM: 64GB of RAM GPU: NVIDIA Quadro NVS 315 HDD: Intel SSDs	FakeSMC, Chameleon and TRIMEnabler installed. Kernel flags in /Extra/org.chameleon.Boot.plist set to "dart=0 ncpi=0x2000." (In particular, it will not boot at all unless ncpi=0x2000 is set, and it will not boot with VT-d enabled unless dart=0 is set). GenericUSBXHCI.kext for USB 3.0 Got the CPU fan to stop oscilliating (BIOS update to 3.0c solved it) For audio, install VoodooHDA 2.8.4. Remove AppleHDA. Replace /System/Library/Extensions/VoodooHDA.kext/Contents/Info.plist with http://pastebin.com/raw.php?i=2fgRNRYq Integrated microphone jacks not working yet, 5.1 surround sound is working. Surround sound requires making an aggregate device in Audio MIDI Setup. Line-Out Green Rear is the front. Line-Out Orange Rear is the back. Line-Out Black Rear is the center and subwoofer. Useful documentation was here: http://olarila.com/forum/viewtopic.php?f=18&t=604 http://www.insanelymac.com/forum/topic/149128-how-to-pinconfig-for-linux-users-%EF%BF%BD-realtek-alc883-example/

[edit] Graphics Cards

Please specify if your card is PCI-E or Integrated.
Also, place chip and board manufacturer in their respective column.

[edit] PCI-E

[edit] AMD/ATI

Model	Board-Manufacturer	Notes	Output	Dual display
Radeon™ HD 4350	Asus	Clover r2565 Bootloader with FakeID 0x94901002 GraphicsEnabler => No and no DefaultFramebuffer Workis still good as Office Card but nothing more	DVI / HDMI	Not tested
Radeon™ HD 4830	Sapphire	Using QE_CI Exotic patch Chameleon 2.0 RC5 (or the most recent) or PCEFI 10.6 Lion + Snow GraphicsEnabler=Yes	DVI / DVI	Not tested
Radeon™ HD 5450	Sapphire	Patched ID 0x68f91002 in AMD5000Controller and ATIRadeonX3000. GraphicsEnabler = No	DVI / HDMI / VGA	DVI+VGA
Radeon™ HD 5770	Sapphire	Install kext PIEROF81Inject.kext Edited by me	Dual DVI / HDMI / DisplayPort
Radeon™ HD 6770	Sapphire	Using those methods Chameleon 2.0 RC5 (or the most recent) or PCEFI 10.6 Lion + Snow GraphicsEnabler => No more need!!!	DVI / HDMI / VGA	Not tested
Radeon™ HD 7790	XFX	Works out of box! Apple includes the brand new AMD8000Controller.kext with 10.10 seeds!	HDMI / VGA Tested, DisplayPort and DVI Not tested	Not tesded
Radeon™ R9 270	Asus	Clover r2671/2747 ATI FakeID: 0x68101002 Inject ATI: True (pretty reporting in profiler, no HDMI) or False (don't care, wants HDMI) FB Name: (not set) Clover Kext Patch (inspired by Vlada's patch): ATIConnectorsController: 7000 ATIConnectorsData: 000400000403000000010101120404010004000004030000000102012205050204000000140200000001030000000606000800000402000000 ATIConnectorsPatch: 040000001402000000010000110205050008000004020000000100002205020200040000040300000001000012040101000200000402000000	DVI / HDMI	Not tested

[edit] NVIDIA

Model	Board-Manufacturer	Notes	Output	Dual display
GeForce GT610 2GB	Twintech	Works OOB	DVI/HDMI/VGA
GTX 660 3072MB SuperClocked Sig2	EVGA	Using default system drivers Chameleon/Clover GraphicsEnabler=No	DVIx2/HDMI/DisplayPort	Not tested
GTX 760 2GB Windforce	Gigabyte	Works out of box with default drivers / also works with nVidia Web Driver No GraphicsEnabler needed Three monitors detected and auto-configured	2xDVI/HDMI/DisplayPort
GeForce 9800GT 512Mo	Twintech	GraphicsEnabler=Yes On AMD kernels, needs reverting to IOPCIFamily + AppleACPIPlatform kexts from 10.9.1 and eventual DSDT patch (for PCI root and/or card details injection)	DVI / DVI

[edit] Integrated

[edit] INTEL

Model	Board-Manufacturer	Notes	QE/CI	Output	Dual display	Compatible 64bit

[edit] Network Cards

[edit] Wireless

Interface	Standard	Device	Manufacturer	Chipset	Notes	Compatible 64bit
USB 2.0	802.11 n / g / b	00062778 WLAN USB 2.0 150Mbps	Hama	Not confirmed (Ralink)	Working with UI 4.0.9.6 Drv: 4.2.9.2 https://www.hama.com/webresources/drivers/00062/00062778_macosx107_108_109_dv4_2_9_2_uiv4_0_9_6.dmg Tested and working properly. Thx to kaefpe.me

[edit] Wired (Ethernet)

Interface	Standard	Device	Manufacturer	Notes	Compatible 64bit

[edit] Sound Cards

Interface	Hardware Name	Manufacturer	Notes	Compatible 64bit

[edit] Webcams

Interface	Item Description	Manufacturer	Notes	Compatible 64bit

[edit] Bluetooth

Interface	Item Description	Manufacturer	Chipset	Notes	Compatible 64bit
USB	Delock 61889 Bluetooth V4.0 dual mode USB adapter	Delock	Broadcom	Works OOB including wake from sleep by Bluetooth device

[edit] USB 3.0 Cards / Adapters

Type of Accessory	Item Description	Manufacturer	Notes	Compatible 64bit

[edit] Keyboard & Mouse

[edit] Wireless

Interface	Item Description	Manufacturer	Model No	Notes	Compatible 64bit

@@ Line 1: / Line 1: @@
 {{Hardware_Components|10.9.3}}
 {{Note|For suggestions about table headings, please join the [http://wiki.osx86project.org/wiki/index.php/Help_talk:Contents discussion here].}}
-{{Note|Keep in mind that OSx86/InsanelyMac does NOT and will NOT support any tools from Tonymacx86 such as MultiBeast or any other -Beast utilities, as per this thread: http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/
-Any mention of Multibeast, Kextbeast or any other Beast tools will be removed at our discretion.}}
 ==Motherboards==
 === Abit ===
@@ Line 76: / Line 73: @@
 |{{Y}}
 |-
+|-
+|[http://www.asrock.com/mb/Intel/Z77%20Pro4/ Z77 Pro-4]
+|Intel Z77
+|'''System Configuration:'''
+*CPU: Intel Core i5 3550 Ivy bridge with oc @ 4100 Mhz (3300 mhz stock freq.)
+*RAM: 1x4GB Kingston 1333 MHz overklocked @ 1800 mhz
+*VGA: ASUS GeForce® 210 EN210 SILENT/DI/1GD3/V2(LP)
+*ETH: 1x Realtek RTL8111E gigabit lan
+*WIFI: Icidu 150N pci-e card, with atheros ar9285 chip
+*SND: Onboard ALC892
+'''System Status:'''
+*All of the above components: {{Y}}
+*Reboot, Shutdown: {{Y}}
+* Sleep: Works: {{Y}}
+|'''Installation method: Pendrive with Mavericks downloaded from App Store and Niresh.co extra's'''
+* Boot flags: ncpi=0x3000 GraphicsEnabler=Yes UseKernelCache=Yes
+* VT-d disabled, Sata on AHCI mode
+* Graphics - Worked OOB {{Y}}
+* Network - Worked OOB {{Y}}
+* WIFI - Works when using [http://forum.osxlatitude.com/index.php?/topic/5690-atheros-ar9285-for-os-x-mavericks/ this kext] {{Y}}
+*USB - Worked OOB {{Y}}
+*USB 3.0 - Worked OOB {{Y}}
+*SATA - Worked OOB {{Y}}
+*App Store - Worked OOB {{Y}}
+*Sound - Works when using VoodooHDA kext {{Y}}
+*Kernel - Vanilla Mach_kernel {{Y}}
+|{{Y}}
+|-
+|[http://www.asrock.com/mb/Intel/Fatal1ty%20Z87%20Professional/ Z87 Fatal1ty Professional]
+|Intel Z87
+|'''System Configuration:'''
+*CPU: Intel Core i7 (Haswell) 4770K @3.5GHz
+*RAM: 16GB (4x4GB) Kingston 1333MHz
+*VGA: Gigabyte GeForce GTX760 WindForce 2GB
+*ETH: 1 x Intel I217-V, 1 x Intel I211
+*SND: Creative Sound Core3D
+*BIOS: 1.90
+'''System Status:'''
+*All of the above components: {{Y}}* (See Notes)
+*Reboot, Shutdown: {{Y}} (OOB)
+* Sleep/Wake: {{Y}} (OOB)
+|'''Installation method:''' USB 10.9.3 from App Store prepared on existing Macbook Pro
+'''Notes'''
+* Boot flags: '''npci=0x1000'''
+* Virtualization, CPU powers states all enabled in BIOS
+* Graphics - {{Y}} (OOB)
+* Ethernet (I217-V) - {{Y}} (OOB)
+* Ethernet (I211-V) - {{N}} Not Detected
+*USB - {{Y}} (OOB)
+*USB 3.0 - {{Y}} (OOB)
+*SATA - {{Y}} (OOB)
+*App Store - {{Y}} (OOB)
+*Sound - {{Y}} (With [http://sourceforge.net/projects/voodoohda/files/VoodooHDA_V286_MAV.pkg.zip/download latest VoodooHDA])
+*Kernel - {{Y}} (OOB)
+|{{Y}}
 |}
@@ Line 239: / Line 293: @@
 *Graphics: Nvidia EVGA GTX760 QE, full 3D acceleration DVI HDMI Dual Monitors{{Y}}
 *Ethernet {{Y}}
-*Audio: ALC892 {{N}}
+*Audio: ALC892 {{Y}}
 *USB 3.0 {{Y}}
 * TimeMachine, App Store, iMessage, Facetime {{Y}}
@@ Line 509: / Line 563: @@
 * HDD: Intel SSDs
 |
-* FakeSMC, Chimera and TRIMEnabler installed.
+* FakeSMC, Chameleon and TRIMEnabler installed.
 * Kernel flags in /Extra/org.chameleon.Boot.plist set to "dart=0 ncpi=0x2000." (In particular, it will not boot at all unless ncpi=0x2000 is set, and it will not boot with VT-d enabled unless dart=0 is set).
 * GenericUSBXHCI.kext for USB 3.0
@@ Line 598: / Line 652: @@
 |Asus
 |
-* Clover r2671
+* Clover r2671/2747
 * ATI FakeID: 0x68101002
 * Inject ATI: True (pretty reporting in profiler, no HDMI) or False (don't care, wants HDMI)
 * FB Name: (not set)
 * Clover Kext Patch ([http://www.osx86.net/files/file/3711-amd-radeon-r9-270-series/ inspired by Vlada's patch]):<br />
-<small><small><pre><dict>
+<small><small>
-	<key>Name</key>
+::ATIConnectorsController: 7000
-	<string>AMD7000Controller</string>
+::ATIConnectorsData: 000400000403000000010101120404010004000004030000000102012205050204000000140200000001030000000606000800000402000000
-	<key>Find</key>
+::ATIConnectorsPatch: 040000001402000000010000110205050008000004020000000100002205020200040000040300000001000012040101000200000402000000
-	<data>AAQAAAQDAAAAAQEBEgQEAQAEAAAEAwAAAAECASIFBQIEAAAAFAIAAAABAwAAAAYGAAgAAAQCAAAA</data>
+</small></small>
-	<key>Replace</key>
-	<data>BAAAABQCAAAAAQAAEQIFBQAIAAAEAgAAAAEAACIFAgMABAAABAMAAAABAAASBAEBAAIAAAQCAAAA</data>
-</dict>
-</pre></small></small>
 |{{Y}}
 |DVI / HDMI
@@ Line 628: / Line 678: @@
 !Dual display
 !colspan="2"| Compatible 64bit
+|-
+|[http://www.twintech3d.com/en/products_features.asp?num=322 GeForce GT610 2GB]
+| Twintech
+|
+* Works OOB
+|{{Y}}
+|DVI/HDMI/VGA
+|{{Y}}
+|{{Y}}
 |-
 |[http://www.evga.com/Products/Product.aspx?pn=03G-P4-2665-KR GTX 660 3072MB SuperClocked Sig2]
@@ Line 633: / Line 692: @@
 |
 * Using default system drivers
-* Chameleon/Chimera/Clover
+* Chameleon/Clover
 * GraphicsEnabler=No
 |{{Y}}
-|DVI x2 / HDMI / DisplayPort
+|DVIx2/HDMI/DisplayPort
 |Not tested
+|{{Y}}
+|-
+|[http://www.gigabyte.com.au/products/product-page.aspx?pid=4657 GTX 760 2GB Windforce]
+|Gigabyte
+|
+*Works out of box with default drivers / also works with nVidia Web Driver
+*No GraphicsEnabler needed
+*Three monitors detected and auto-configured
+|{{Y}}
+|2xDVI/HDMI/DisplayPort
+|{{Y}}
+|{{Y}}
+|-
+|[http://www.twintech3d.com/en/products_features.asp?num=229 GeForce 9800GT 512Mo]
+|Twintech
+|
+*GraphicsEnabler=Yes
+*On AMD kernels, needs reverting to IOPCIFamily + AppleACPIPlatform kexts from 10.9.1 and eventual DSDT patch (for PCI root and/or card details injection)
+|{{Y}}
+|DVI / DVI
+|{{Y}}
 |{{Y}}
 |-

Tools

3.238.250.105

HCL 10.9.3

Latest revision as of 01:43, 8 November 2014

Contents

[edit] Motherboards

[edit] Abit

[edit] Alienware

[edit] Asrock

[edit] Asus

[edit] Biostar

[edit] EVGA

[edit] Foxconn

[edit] Gigabyte

[edit] Intel

[edit] MSI

[edit] PCWARE

[edit] QUO

[edit] Supermicro

[edit] Graphics Cards

[edit] PCI-E

[edit] AMD/ATI

[edit] NVIDIA

[edit] Integrated

[edit] INTEL

[edit] Network Cards

[edit] Wireless

[edit] Wired (Ethernet)

[edit] Sound Cards

[edit] Webcams

[edit] Bluetooth

[edit] USB 3.0 Cards / Adapters

[edit] Keyboard & Mouse

[edit] Wireless