OSx86:HCL 10.6.8

• Asus P5KPL-AM EPU
• Asus EN8400GS
• Intel E6700 DualCore 3.2GHz
• Corsair DDR2 800MHz 4GB Kit

Install:

1. iBoot with retail 10.6.0 (on USB HD)
2. Boot system with iBoot
3. update with 10.6.8 combo updater (don't reboot)
4. Multi Beast -> EasyBeast Install, UserDST Install, 64-bit Apple Boot Screen
5. kexts: AttansicL1eEthernet, VT1705 (works fine with VT1708), SleepEnabler for 10.6.8

• Ethernet: works
• Audio: works
• Video: works
• Sleep: works

VT1705 SleepEnabler 10.6.8

System: ASUS P5Q SE2, NVIDIA Geforce 8800GT 512mb, Intel Core 2 Quad Q8300, 6GB RAM, 500GB WDC

1. Install retail Mac OS X 10.6 with IBoot
2. download & Install MultiBeast
3. download OSX Combo update
4. Install Mac OSX combo update 10.6.8

• Ethernet: Works
• Audio: Works with VoodooHDA

Video: Works

System: ASUS P5-VM, AMD Sapphire 5670 1GB, Intel Core 2 Quad Q6600, 8GB RAM, 320GB Seagate w/2 more SATA drives

1. iAtkos s3 10.6.3 disk
2. Boot in safe mode w/verbose just to see what's going on (-x -v)
3. download OSX Combo update
4. Install Mac OSX combo update 10.6.8 to enable 5670 without injectors/hacks/etc.

• Ethernet: patched from DVD with 8168 kext.
• Audio: Requires AppleHDA_ALC1200_HDEF.zip patch [from Forum].

• Intel Core 2 Quad Q6600
• IDE DRIVE & IDE DVD-RW
• 6GB RAM
• Nvidia GeForce 9400 GT

Follow this guide

System: ASUS P6T Deluxe V2, Intel Core i7-920, 2.66 GHz, 6gb Kingston HyperX

• SATA - Works with AHCI set in BIOS
• USB - Works
• Ethernet: Works
• Audio works after you run 10.6.x audio patch by Fabio and aschar
• Video Palit Gtx 285 (1024MB) DDR3 - Works

Installation: iBoot (3.1.0) + Multibeast (3.7.3). Installed from the original Snow Leopard 10.6.3 DVD and then upgraded (via ComboUpdate) to 10.6.7. then update 10.6.8 by Software Update

• Multibeast: used UserDSDT build by DSDT Auto-Patcher.
• Monitor : connected via DVI.
• Video: Multibeast (NVEnable)
• Audio: AppleAzaliaAudio.kext
• Ethernet: AtherosL1Ethernet.kext
• USB: OOB
• SATA/IDE: OOB

NVEnable

Installation: iBoot (3.1.0) + Multibeast (3.7.3). Installed from the original Snow Leopard 10.6.0 DVD and then upgraded (via ComboUpdate) to 10.6.7. Multibeast: used the EasyBeast Install and applied the patches. No custom DSDT used. Monitor connected via DVI. Video: Out of the box Audio: VoodooHDA 0.2.72 (microphone not working) Ethernet: Lnx2Mac's RealtekRTL81xx USB: Out of the box SATA/IDE: Out of the box

VoodooHDA 0.2.72 Lnx2Mac's RealtekRTL81xx

• Intel Core i5-750 2.66 Ghz
• SATA HD 1 TB (switched on AHCI configuration from IDE) and SATA SONY DVD-RW DL
• 2x2GB (4GB) RAM Corsair Dominator XMS3 1600 Mhz
• Sapphire Ati Radeon HD 5770 1 GB Vapor-x

Install Mac with iAtkos S3 v2 with this configuration:

Important: If the iAtkos installer crashes on start, start the pc using the iAtkos DVD and press F8, write this "-v cpus=1 busratio=20", it will work.

• 1) Chameleon RC4 bootloader
• 2) Boot with 32-bit mode
• 3) DON'T USE Graphic Enabler for now.
• 4) In Bootloader options --> USB check all.
• 5) In the same menu check Ethernet too and, if you want, check Legacy Logo (you will have the original Apple Logo when booting)
• 6) In "Patches" menu don't touch anything. Don't use modified kernels or USB fixes.
• 7) In "Drivers" menu check only "Main Hardware" --> "Sound" --> Both drivers (Vodoo and Apple). If you use PS/2 keyboard or mouse, check PS/2 too.
• 8) Don't touch VGA for now.
• 9) In network choose Wired (if you're connecting with Ethernet) and select Realtek --> RTL8168.
• 10) In Language Translations choose your language.
• 11) Install all.
• 12) Reboot and log on the OS. If MacOS come up with an error and you need to restart the computer, still use "-v cpus=1 busratio=20" for every boot.
• 13) To install VGA drivers, download Kext Helper v0.7 (this is the last version for now) and download ATI 5000 Series drivers 32-bit from www.kext.com. Use Kext Helper to install all the content from the ATI 5000 Series driver directory.
• 14) Install Apple Combo Update to get 1.6.8 version.
• 15) Enjoy your system.

With this configuration all works: VGA, USB and internet connection.

• full installation proccess is here [2]

• Used Multibeast 3.8 with lnx2mac Realtek 81xx drivers, USB fix, PCI fix and com.apple.boot.plist's PCIRootUID=1 key
• HD 5750 graphics don't work with 10.6.8 drivers, reinstalled 10.6.7 ATI kexts back.

• Using iBoot and 10.6.3 Retail DVD, install 10.6.3. No other patch required.
• Apply UpdateHelper by tonymac, Reboot, Install Combo Update 10.6.8, DO NOT REBOOT
• Apply Multibeast 3.8, select easybeast, lnx2mac, system utilites, ALC8xxHDA + AppleHDA Rollback + EnableHDA

Sound, LAN, Graphics (fully), USB, restart/shutdown, timemachine everything is working (Sleep not tested)

• CPU i7 2600K
• MEMORY G.Skill 2x2G 1600Mhz
• GPU Gigabyte GTS250 VGAxDVIxHDMI
• Asus ML 24 (HD) - works with VGA connector only (no native HD so far with my card)
• DVD WR Samsung

Start with Simple installation without iBoot (used the DVD own bootloader). Do Not use the DSTD instructions when installer loads. just run the default installation.
After installation, used the iBoot to load into the OSX.
Run MultiBeast and pick:
EasyBeast.
intel 1000 network.
To Enable Sound: AppleHDA Rollback, ALC8xxHDA, Under Non-DSTD HDAEnabler - pick "ALC892"

[pre-requisite for sandy bridge & 10.6.8 combo update] Run "UpdateHelper" (from tonymacx86 site).
Reboot

When OS loads it might not be responsive in the first few minutes, just wait ~2minutes.
Install Snow 10.6.8 Combo Update
[optional, if you have issues with bootloader] Use iBoot to load OSX and then run MultiBeast and re-install the Bootloader + SystemUtils (should fix the bootloader issues if any)
Reboot

• Asus Sabertooth X58
• MSI R5770 Hawk
• Intel Core i7-960 Bloomfield 3.2GHz
• G.SKILL Sniper Low Voltage Series 8GB (2 x 4GB)

Install:

1. iBoot with retail 10.6.3 (Retail CD)
2. Boot system with iBoot
3. update with 10.6.8 combo updater (don't reboot)
4. Multi Beast -> UserDST Install, System Utilities, 64-bit Apple Boot Screen
5. kexts: USB 3.0-NEC/Renesas

• Ethernet: works
• Audio: works
• Video: works
• Sleep: works

• Asus E35M1-M
• Gigabyte Nvidia 240 GT
• AMD Fusion APU E-350 (Dual Core overclocked to 1.76 GZ)
• Kingston DDR3 1333 4GB Kit (overclocked at 1433)

Install:

1. Installed retail 10.6.0 on another mac (show invisible files then installed from Installation/Packages/OSInstall.mpkg)
2. updated to 10.6.8 combo updater
3. Multi Beast -> VoodooHDA 0.2.61 (audio for HDMI works) / Lnx2Mac's eraltek network driver
4. Legacy kernel from nawcom (patched with Maxxus AMD patcher) in com.apple.Boot.plist "arch=i386 -force64 busratio=20"

• Ethernet: works
• Audio: works
• Video: works
• Sleep: not tested

Iatkos options default just add video, ahci sata and jimicron, evospeedstep,quick boot,legacy logo, leguage as well and uncheck sound. dont need dsdl usb work out of the box. sleep doesn´t work

Iatkos options default, efi string, ahci sata and jimicron, evospeedstep,quick boot,legacy logo, leguage as well and uncheck sound. dont need dsdl usb work out of the box. sleep doesn´t work.

• CPU Xeon E5620 2.4ghz
• MEMORY ADATA 12 ghz 1333mhz non ECC in 3 slots
• GPU GTS250 dual dvi (works as first class)
• DVD WR Lg Generic Sata
• HDD 3 X 1TB seagate sata II
• nedd help with sleep????

• Intel Core 2 Duo E4500 2.2GHz, 4GB DDR2
• NVIDIA GTX275 896MB DDR3
• Both processors working with proper fix applied in DSDT.aml file (which is already done in my DSDT) or 6B3F1P40 modified BIOS by OriginalMACNUT, otherwise Cpus=1 fix must be enabled.

... Install ...

• 10.6.3 Retail DVD
• Install method - Installed Retail DVD from 8GB thumb drive

... Post-Install ...

• Bootloader - Chameleon-2.0-RC5-r1091
• Audio - patched AppleHDA or VoodooHDA
• Video - using DSDT patch, but also all other methods are working
• Ethernet - Works OoB
• SMC - FakeSMC rev.474
• 10.6.8. updated w/o single problem
• Sleep/Wakeup works properly with my DSDT
• Shutdown/restart working properly

• Foxconn G41MXE-V LGA 775 Intel G41 Micro ATX Intel Motherboard
• Intel Celeron E3400 Wolfdale 2.6GHz 1MB L2 Cache
• 4GB ram
• EVGA GeForce 8600 GTS 512MB
• All defaults in configuration except I selected realtek ethernet drivers, nvenabler
• Sleep not working OOB, it seems. Don't care to try to fix it
• Shutdown/restart working
• Audio working
• Graphics acceleration confirmed (dashboard add item - waves)
• Good picture over DVI on my 1080p monitor
• Running synergy client so I can use my keyboard/mouse from my main windows box. Highly recommended - just move mouse across to mac screen
• Edit: Updated using software update to 10.6.8 with no issues.

• Intel Core 2 Duo E7200 Wolfdale 2.5GHz 3MB L2 Cache
• 4GB DDR2 800 (2x2GB) ram
• Ati Radeon HD 5670 1GB DDR5 / Onboard GMA950 working with Leohazard drivers and full QE/CL with [4]
• All defaults in configuration except + ATY_init enabler (to have UI at first boot)
• Shutdown/restart working
• Audio working with Legacy HDA
• FULL QE/CL
• Dual display VGA+DVI, HDMI not tested but shows up in System Profiler under Graphics
• USB/PS2 working both OOB

• BIOS updated : September, 06 2010
• Intel Core 2 Duo 2.7 Ghz
• Memory : 2GB of Ram (DDR3)
• VGA : nVidia Geforce 8400 GS 512 MB
• Audio : Full working
• Network Full working
• Graphic Full working with QE/CI
• Monitor : Hp w1707 with connect by DVI Cable
• Hard Disk : Seagate 1TB

• Installed 10.6 Retail by EmpriseEFI CD + Combo update to 10.6.8
• Use Multibeast to Restore USB functions, installed fakesms.kext, and installed Chameleon RC5 R699, you can choice some different files if you need )
• Bootloader - Chameleon RC5 or Chimera 1.1 (Tested on May 6, 2011)
• DSDT created by DSDT autopacher and it's so amazing :)
• Audio - Voodoo HDA 0.2.1 Modded to link from Speaker to PCM with Volume Control worked perfectly.
• Video - nVidia Geforce 8400 GS 512 MB (just only add GraphicsEnabler=y to com.apple.Boot file or you can using nVEnabler.kext)
• SATA - AHCI in BIOS (Set up default on BIOS)
• Note : You must saving ACPI + PCI 10.6.7 for 10.6.8 from 10.6.7 install in here to boot without error PCI Config, just on 10.6.8
• Ethernet - AtherosL1Ethernet.kext (the below link it's lastest version to fix any random kernel Panic).
• Sleep & Wakeup : Works no need to SleepEnable.kext !
• Here all my file with GA-G41M-Combo: [5] (Found on 3 days to take full files)

• CPU Intel E6600 @ 2,40 GHz
• Install with original DVD + iBoot + update to 10.6.7 from Apple + update 10.6.8 : flawless

• Geforce 8400GS
• Sound: ALC888
• Ethernet: working
• Install BIOS cartri,

Combo Update to 10.6.8 from 10.6.7 need 3 new patched kexts for sound, from www.kext.com

• For Install use: Kakewalk[6]
• Mic (green Line) works fine.
• Sleep and Wake up works perfect.
• Shutdown/Restard works fine.
• LAN (DHCP) works fine.
• If you dont want use Cartri BIOS, check following DSDT: [7]

• Zipped Extra Folder: [8]
• FakeSMC.kext - Multibeast 3.8.0
• AppleHDA.kext
• IOAHCIBlockStorageInjector.kext - Multibeast 3.8.0
• No DSDT File needed -> Cartri 0.8 BIOS [9]

• Video: GTX260 - NVenable + GT200driver.pkg+CUDA Driver for CUDA suport "adobe and more"
• Sound: Voodoo HDA works OK mic in line in
• Ethernet: working
• Reboot work / sleep not work
• Install Original DVD Snow Leopard 10,6,3 and iBoot+Multibeast Easy Instal + Vodoo HDA + NVENABLE

Combo Update to 10,6,8

• Video - eVga 8400GS 1GB DDR3 64-bit - Works with editing NVDANV50Hal.kext and PCIRootUID=1
• Sound - MultiBeast AppleHDA Rollback and ALC889
• Ethernet - MultiBeast Realtek drivers
• Reboot / Sleep - Works
• iBoot + Multibeast install guide used with DSDT: Fresh 10.6.0 -> Mac OS X 10.6.8 Helper -> 10.6.8 Combo Update -> Mac OS X 10.6.8 Helper -> MB -> Reboot -> Edit NVDANV50Hal.kext -> Reboot

• Video: ATI-5770 (Powercolor)
• Sound: Realtek ALC892 - need AppleDHA Rollback after update from 10.6.7 to 10.6.8
• Ethernet: working
• Reboot / sleep works with spleasesleep
• iBoot + Multibeast install guide used with DSDT

• Video: ATI-5770, Needs unplug replug after restart, or wait until screensaver kicks in
• Sound: Realtek ALC889 - works
• Ethernet: working
• Reboot / sleep works
• iBoot + Multibeast install guide used with DSDT

• Video: ATI Sapphire 5850HD Vapor X, work OOB
• Sound: Realtek ALC889a after the update you have to reinstall AppleHDA with multibeast (appleHDa rollback)
• Ethernet: working. I installed the Lnx2Mac Realtek RTL81xx Driver. (Look it up online) So far it works well. Make sure to select the debug install option.
• Reboot / sleep works
• update from 10.6.6 (boot 132 + multibeast)

• CPU: Intel Pentium Dual Core E5800 @ 3.20 GHz
• RAM: 4 GB (2x2GB) Patriot DDR2 800 MHz
• Graphics: Gigabyte GeForce GT 220 1 GB DDR3 (Use NVEnabler, 64-bit preferred)
• Audio: RTL888b (Actual Kext, but you need to find this package "10.6.2-AppleHDAInstaller.pkg" for it to work)
• Ethernet: RTL81xx
• Wireless: Edimax EW-7811UN USB 2.0 Wireless Adapter: Installer package can be downloaded from vendor website. Plug in before installation starts
• Bluetooth AZiO BTD211 USB 2.0 Bluetooth Adapter: Plug in before installation starts
• Webcam: HP Webcam 3100: Plug in before installation starts
• Reboot, Sleep, 64-Bit Kernel Completely Work
• Installation Guide:
• iBoot 2.0.4 + Multibeast 3.7.2 + OSX 10.6.3 Retail DVD
• Download Before Install: OSX 10.6.8 Combo Update + DSDT Auto-Patcher + HDEF Gigabyte DSDT Auto-Patcher + AudioKext Package
• After install has completed and you reboot with iBoot, run combo update, but before you restart to finish the update run the packages in this order:
• 10.6.2-AppleHDAInstaller, DSDT Auto-Patcher, then HDEF Gigabyte DSDT Auto-Patcher (it will overwrite original DSDT), run Multibeast (select UserDSDT, NullCPU.....kext, EvoReboot.kext, Repair Permissions, Repair Caches, NVEnabler.kext, and any SMBIOS or 64-bit plist you prefer).
• When you are done, you will be booting into Chimera (no need for -v or -x, but do it if you choose) with a complete installation.

• CPU Intel Core i3 540 @ 3,06 GHz
• Video: 9800GT PNY recertified dual DVI, work OOB with graphic enabler=yes
• Sound: Realtek ALC889a after the update you have to reinstall AppleHDA with multibeast (rollback, legacy and enabler)
• Ethernet: install with multibeast
• Reboot / sleep works with sleepenabler 10.6.8 kext.
• install method iboot and multibeast, install mac os x 10.6.3 retail dvd (use -v if boot issues), boot with iboot cd, install mac os 10.6.7 update, select in multibeast dsdl install with all kexts you need and utilities,except audio and sleepenabler (if you cant use usb reboot with usb put in cpu), use everything from multibeast except fakesmc (dont show cpu temperature)need to use a older one an put it in extra files after multibeast finish,now use kextutilities an reboot,now install 10.6.8 update dont reboot use multibeast and install audio and sleepenabler, reboot and thats all, LegacyIOAHCIBlockStorage.kext to avoid yellow hard disk.
• and please dont use 240GT dont work at 100% check in nvidia section i posted.

• fakesmc.kext (old one)
• NullCPUPowerManagement.kext*sleepenabler 10.6.8
• LegacyIOAHCIBlockStorage.kext
• nec usb 3 patch
• and ethernet from multibeast the first one
• dsdt F11 from tonymacx86 in dsdt section

• works like a charm, Graphics working (Sapphire Radeon HD 5850), Sound working, Ethernet working even Sleep Mode working (turn's off all fans, consums only 16W in sleep), USB 3 ports are working with full speed, SATA 3 works with full speed
• iBoot + Multibeast 3.8.0
• check tonymac DSDT database
• read further instructions here: [10] will write a better tutorial soon
• see posts by username "Seim" for Multibeast settings

• Install 10.6.3 using iAKTOS s2 v3
• Install 10.6.8 combo update, DO NOT RESTART
• Install multibeast 3.8 with easybeast install option
• Restart system
• Enjoy (Not sometime it stuck on boot screen, try with -v and boot a couple of times)
• I have dual boot windows and SL 10.6.8, windows7 was already installed.

• Install Method: Retail Disk Image install on Hackintosh or Mac - Apple Software Combo Update to 10.6.8 - Chameleon 2.0 RC4 R684 - /Extra/Extensions
• GMA950 - Works
• Audio - works Voodoo
• Ethernet - works
• 10.4 - 10.6 compatible

• DSDT.aml
• AppleACPIPS2Nub.kext
• ApplePS2Controller.kext
• fakesmc.kext
• IOATAFamily.kext
• IOUSBFamily.kext
• NullCPUPowerManagement.kext
• OpenHaltRestart.kext
• PlatformUUID.kext
• RealtekR1000.kext
• SleepEnabler.kext
• VoodooHDA.kext

• Install Method: Retail Disk Image install on Hackintosh or Mac - Apple Software Combo Update to 10.6.8 - Chameleon 2.0 RC4 R684 - /Extra/Extensions
• GMA950 - Works
• Audio - works Voodoo
• Ethernet - works
• 10.4 - 10.6 compatible

• DSDT.aml
• AppleACPIPS2Nub.kext
• ApplePS2Controller.kext
• fakesmc.kext
• IOATAFamily.kext
• IOUSBFamily.kext
• IONetworkingFamily.kext
• NullCPUPowerManagement.kext
• OpenHaltRestart.kext
• PlatformUUID.kext
• SleepEnabler.kext
• VoodooHDA.kext

• Works to EVOenabler and ID 0x71001002 -> (ATIRadeonX1000.Kext)
• Dual DVI works
• Fully Works
• By PieroF81

• Works with these kexts [11] replace kexts in /System/Library/Extensions. Also included a boot file, which needs to be replaced in the root folder.
• Add GraphicsEnabler=Yes in com.apple.boot.plist, then repair permissions with kext utility.

• ATI48xxInjector.kext[12] from MultiBeast[13] 3.7.3 placed in E/E
• Chameleon 2 RC5 r1155[14] with GraphicsEnabler=Yes in org.chameleon.Boot.plist.

After updating to 10.6.8 [combo update] works OOB.

• Works almost OOB after a clean install with Leohazard 10.6.2 + combo 10.6.8 update using latest Chimera or latest bootloader from kabyl.
• GraphicsEnabler=Yes, UseATIRom=Yes and place your rom in /Extra.
• Use following rom: [15] Rename to "1002_68D8_03561043.rom".

• Worked OOB after 10.6.8 update from iATKOS S3 v2 10.6.3 clean install.
• GraphicsEnabler=Yes.

• Worked OOB after 10.6.8 update from iAtkos 10.6.3 clean install.

• works OOB with Chimera Bootloader (included in Multibeast) and GraphicsEnabler=yes
• DisplayPort is NOT working, just a black screen but it recognize that something was plugged in
• DVI works just up to FullHD resolution (1920x1080) if you have a resolution above this you have to plug out the cable and plug it back in to have a picture (everytime after booting)

• With GraphicsEnabler in Chameleon as supplied with Blackosx's boot loader and supporting files.
• Is working with the Apple LED Cinema 27" display via Atlona Dual-Link to mini-DisplayPort adapter.
• Works via both direct connection of above monitor to mini-DisplayPort and via Atlona adapter to DVI port (both connection methods working in both Windows 7 and OSX 10.6.8).

• Works with NVenabler.kext (during Multibeast) or graphics enabler=yes (chimera efi)
• Important i already use this 2 cards in hackintosh and dont work 100% right you can see this in photoshop open a picture press f 2 times,them h, now move picture with mouse and see that the picture blink or movements are not syncro with mouse but if you use a real mac or use other cards like 9800gt, 250gts or 8600gts you dont have those kind of problems really is a problem if you use photoshop or photo edit software take care. and with enabler gpu is unknow in graphics info and dont use nvidia rom from card. i dont understand why tonys recomend this card i already try everything and dont work at 100%

VGA/VGA With Adapter